City of West Palm Beach eGovPlus

Plan Review Details - Permit 07051152

Plan Review Stops For Permit 07051152

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2007-07-08			Cont ID
Sent By	amorse			Date	2007-07-08	Time	19:18	Rev Time	0.00
Received By	amorse			Date	2007-07-08	Time	19:18	Sent To	PC

Notes

2007-07-08 19:55:15

	DENIED

	1)PROVIDE DESIGN PARAMETERS ON DRAWINGS THIS INCLUDES
	THE CODE CYCLE (2004 FBC W/ 2006 AMENDMENTS) AND THE
	TYPE OF CONSTRUCTION

	2)BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
	FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
	PERMIT SETS OF PLANS MUST BE STAMPED BY THAT OFFICE,
	AND A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
	APPLICATION. PLEASE CALL (561) 233-5025 FOR MORE
	INFORMATION.

	3)THE STATE OF FLORIDA REQUIRES COLLECTION OF A RADON
	SURCHARGE ON ALL NEW CONSTRUCTION COMPUTED ON UNDER
	ROOF FLOOR SPACE PER 10D-91 FAC. THESE FEES WILL BE
	ADDED TO THE PERMIT APPLICATION FEES

	4)THE PERMIT APPLICATION SHALL INCLUDE TWO COPIES OF
	EACH PRODUCT APPROVAL THAT IS RELEVANT PER 9B-72. THESE
	SHOULD INCLUDE THE FLORIDA STATE APPROVAL COVER PAGES,
	AND THE PRODUCT NOA THAT LISTS THE SYSTEM COMPONENTS/
	FASTENER LIST PAGES, THE PAGES WITH THE CHOSEN
	ASSEMBLY/ SYSTEM TO BE USED AND THE GENERAL LIMITATIONS
	PAGE. ALL CAN BE FOUND ON WWW.FLORIDABUILDING.ORG

	5)THOSE PRODUCTS WHICH ARE REGULATED BY DCA RULE
	9B-72 SHALL BE REVIEWED AND APPROVED IN WRITING BY THE
	DESIGNER OF RECORD PRIOR TO SUBMITTAL FOR
	JURISDICTIONAL APPROVAL PER 106.3.3 FBC*

	6)THE CITY OF WEST PALM BEACH REQUIRES THE FLORIDA
	STATE PRODUCT APPROVAL COVER SHEETS WHEN AVAILABLE.
	THEY CAN BE SEARCHED FOR ON WWW.FLORIDABUILDING.ORG.
	WHEN AVAILABLE AND NOT SUBMITTED APPLICATIONS WILL BE
	DENIED

	7)PROVIDE 2 COPIES OF RECENT SURVEY THAT SHOWS ALL
	EXISTING AND PROPOSED WORK, COMPLETE WITH ALL FRONT,
	SIDE AND REAR SETBACKS FROM BUILDINGS AND EQUIPMENT.

	8)IN AREAS OF QUESTIONABLE SOILS AS SHOWN IN THE
	OFFICIAL ZONING MAP OF THE CITY OF WEST PALM BEACH, 2
	COPIES OF A SOIL TEST REPORT SHALL BE SUBMITTED PER
	R401.4

	9)PROVIDE A SITE PLAN THAT SHOWS DRAINAGE IN
	COMPLIANCE WITH THE REQUIREMENTS OF R403.1

	10)SUBMIT ENGINEERED TRUSS DRAWINGS THAT
	COMPLY WITH R802.10.1 FBC WITH PERMIT
	APPLICATION OR BEFORE INSTALLATION THAT
	HAVE BEEN REVIEWED AND APPROVED BY THE
	DESIGNER OF RECORD

	11)PROVIDE THEVALUATION ON THE PERMIT APPLICATION.
	FOR PERMITTING PURPOSES, VALUATION OF BUILDINGS AND
	SYSTEMS SHALL BE THE TOTAL REPLACEMENT COST EXCLUDING
	LAND VALUE. OUR VALUATION REFERENCE IS ICC (BVD),
	MARSHALL-SWIFT AND MEANS COST ANALYSIS SERVICES PER
	108.3 FBC*. IF VALUE IS FOUND TO BE LOW ADJUSTMENTS
	WILL BE MADE AND FEES DUE.

	12)SUBMIT ENERGY CALC'S PER 13-101.2.2 FBC. BE SURE
	THAT THEY ARE SIGNED AND DATED BY PREPARER AND
	OWNER/AGENT PRIOR TO SUBMITTAL

	13)FOUNDATION PLAN SHALL CONTAIN NOTES FOR VAPOR
	BARRIER AND TERMITE SOIL TREATMENT PER R506.2.3 & R320
	FBC RES.

	14)PROVIDE NOTE AT ALL SHOWER DOORS TO MEET SAFETY
	GLAZING IN HAZARDOUS LOCATIONS PER R308.4 ALSO DOOR
	SCHEDULE ON A/3 SHOWS SHOWER DOORS AS 1 1/2" THICK AND
	THE WALK IN CLOSET AS 3/8" THICK

	15)PROVIDE SMOKE ALARMS AT EACH LEVEL PER R313.1 FBC
	RES.

	16)STAIR HANDRAIL/GUARDS SHALL NOT ALLOW THE PASSAGE
	OF A 4" SPHERE PER R312.2 FBC RES.

	17)SECOND FLOOR LINTEL MARKS ARE NOT ASSIGNED IN
	BUILDINGS 1 & 2 ON SHEET A/10

	18)LINTEL SCHEDULE SHOWS ALL SIZES AS 8F24 YET
	SECTIONS SHOW A 8F16 PLEASE CLARIFY

	19)SECOND FLOOR FRAMING PLAN ON A/10 DOES NOT
	DESIGNATE A BEAM SIZE

	20)PROVIDECOMPLETE CONNECTOR SCHEDULE WITH THE
	FLORIDA STATEWIDE APPROVAL NUMBERS (THIS SAVES PRINTING
	OF ALL PRODUCT APPROVALS FOR EACH CONNECTOR)

	21)A RECORDED COPY OF THE NOTICE OF
	COMMENCEMENT IS REQUIRED PRIOR TO A PERMIT BEING
	ISSUED

	BLDG PLAN REVIEW
	ADRIAN MORSE
	561-805-6716

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2007-06-15			Cont ID
Sent By	btrobaug			Date	2007-06-15	Time	16:51	Rev Time	0.00
Received By	btrobaug			Date	2007-06-15	Time	15:49	Sent To	M

Notes

2007-06-15 16:51:22

	NONCOMPLIANT

	PLEASE MAKE THE FOLLOWING CORRECTIONS FOR CODE
	COMPLIANCE AND RESUBMIT FOR REVIEW.

	1} PROVIDE A RISER DIAGRAM WITH CONDUCTOR AND CONDUIT
	SIZE AND TYPE, GROUNDING DETAILS, LOAD CALCULATIONS,
	PANEL SCHEDULES, SERVICE EQUIPMENT AND PANEL LOCATIONS
	PER 106.3.5.4 FBC. AND AIC RATING FOR EACH SERVICE.

	2} FOR THE PANEL SCHEDULE/LOAD CALCULATION THAT IS
	SUBMITTED WITH THIS SET.
	A) TWO SMALL APPLIANCE CIRCUITS ARE REQUIRED PER
	210.11(C)(1), 220.52(A).

	B) BATH CIRCUIT REQUIRED TO HAVE A 20 AMP RECEPTACLE
	PER 210.11(C) (3),

	C) LAUNDRY CIRCUIT PER 220.52(B), @ 1500 WATTS.

	D) DRYER MUST BE CALCULATED PER 220.54 @ 5000 WATTS.
	ALSO SEE THIS IS ON A 40 AMP BREAKER WITH A 900 WATT
	LOAD.

	F) 408.4 CIRCUIT DIRECTORY OR CIRCUIT IDENTIFICATION
	EVERY CIRCUIT AND CIRCUIT MODIFICATION SHALL BE LEGIBLY
	IDENTIFIED AS TO ITS CLEAR, EVIDENT, AND SPECIFIC
	PURPOSE OR USE. THE IDENTIFICATION SHALL INCLUDE
	SUFFICIENT DETAIL TO ALLOW EACH CIRCUIT TO BE
	DISTINGUISHED FROM ALL OTHERS.

	3} 210.52(E) OUTDOOR OUTLETS FOR A ONE-FAMILY DWELLING
	AND EACH UNIT OF A TWO-FAMILY DWELLING THAT IS AT GRADE
	LEVEL, AT LEAST ONE RECEPTACLE OUTLET ACCESSIBLE AT
	GRADE LEVEL AND NOT MORE THAN 2.0 M (6 1/ 2 FT) ABOVE
	GRADE SHALL BE INSTALLED AT THE FRONT AND BACK OF THE
	DWELLING.

	4} WATER HEATERS ARE REQUIRED TO HAVE
	DISCONNECTS.422.16.THERE IS A RECEPTACLE SYMBOL SHOWN.

	5} KITCHEN RECEPTACLE SPACING MUST COMPLY WITH
	210.52(A), 210.52(C), AND 210.8(A)(6) GFI. ALL UNITS IN
	SPACING VIOLATION.

	6} SMOKE ALARMS AND SMOKE DETECTORS SHALL NOT BE
	INSTALLED WITHIN A 914-MM (36-IN.) HORIZONTAL PATH FROM
	A DOOR TO A KITCHEN OR A BATHROOM CONTAINING A SHOWER
	OR TUB. 11.8.3.5(5) NFPA-72, 2002. PER 313.1 WILL BE
	REQUIRED ON THE SECOND FLOOR.

	7} THE PERSON TAKING RESPONSIBILITY FOR THE DESIGN MUST
	PRINT AND SIGN THEIR NAME TO SAME PER 106.3.4.3. FBC.
	IF AN ARCHITECT OR ENGINEER, COMPLY WITH 418 AND 417
	FS, RESPECTIVELY.

	NOTE: REFERENCING SHEET A1 "WALL LEGEND"PER 2704.1,
	2004 FBC, METAL FRAMING MEMBERS SHALL BE BONDED TO THE
	EQUIPMENT GROUNDING CONDUCTOR FOR THE CIRCUIT THAT MAY
	ENERGIZE THE FRAMING. PLEASE SEE ARTICLE.

	IF THERE ARE ANY QUESTIONS PLEASE CALL.

	BILL TROBAUGH
	ELECTRICAL PLANS EXAMINER
	CITY OF WEST PALM BEACH
	561/805-6718
	[email protected]

Review Stop	ENG			ENGINEERING CSD
Rev No	1	Status	N	Date		Cont ID
Sent By				Date	Time	Rev Time
Received By				Date	Time	Sent To

Notes

***NONE***

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	N	Date		Cont ID
Sent By				Date	Time	Rev Time
Received By				Date	Time	Sent To

Notes

***NONE***

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date				Cont ID
Sent By				Date	2007-07-08	Time		Rev Time	0.00
Received By	adarroug			Date	2007-06-04	Time	11:16	Sent To

Notes

2007-06-04 11:16:41

TO "SFR" "Z"

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2007-06-18			Cont ID
Sent By	tgordon			Date	2007-06-18	Time	15:54	Rev Time	0.35
Received By	tgordon			Date	2007-06-18	Time	15:54	Sent To	P

Notes

2007-06-18 16:09:55	PLAN REVIEW ONLY NOT FOR PERMIT.
	* DENIED *
	1) PLEASE SUBMIT ENERGY CALCULATIONS, SEE 2004 FBC
	13-101.2.1.

	2) PLEASE SUBMITCOOLING LOAD CALCULATIONS (MANUAL J
	CALCULATIONS), SEE 2004 FBC 13-607.1.ABC.1 .

	3) PLEASE SHOW ON MECHANICAL PLANS AN EQUIPMENT LISTING
	WITH ALL PERTINENT INFORMATION.

	4) PLEASE SHOW CLOTHES DRYER VENT TERMINATION ON
	MECHANICAL PLANS (ALL UNITS), SEE 2004 FBC/R M1501.

	5) SHOW ON MECHANICAL PLANS ALL BATHROOM EXHAUST FANS
	AND THE CFM'S.

	6) PLEASE PROVIDE RETURN AIR TO THE FIRST FLOOR OFFICE
	(ALL UNITS),SEE 2004 FBC/R M1602.4.

	7) SHOW HOW THE SECOND FLOOR RETURN AIR IS GETTING BACK
	TO THE SECOND FLOOR AIR HANDLER UNIT (IF LOUVERED DOOR
	PLEASE SHOW ON MECHANICAL PLANS.

	MECHANICAL PLAN REVIEW BY;
	TOM GORDON (561) 805-6729.

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2007-06-22			Cont ID
Sent By	mperson			Date	2007-06-22	Time	14:05	Rev Time	0.45
Received By	mperson			Date	2007-06-22	Time	14:05	Sent To	B

Notes

2007-06-22 14:27:06	DENIED
	REFERENCE:
	** FBC-2004 PLUMBING.
	** FBC-2004 CHAPTER 1, THE CITY OF
	WEST PALM BEACH AMENDMENTS.
	** FLORIDA ADMINISTRATIVE CODE.
	** FLORIDA STATUTES.

	PLAN REVIEW ONLY NOT FOR PERMIT
	THE FOLLOWING CORRECTIONS/INFORMATION ARE REQUIRED FOR
	PLUMBING PLAN REVIEW TO MEET CODE COMPLIANCE:

	1. SHEET M3 PLUMBING RISER: THE SANITARY ISOMETRIC
	RISER DIAGRAM INDICATED ON THIS SHEET DOES NOT REFLECT
	ANY OF THE THREE TOWNHOUSES. PLEASE COMPLY WITH THE
	FOLLOWING. PER FBC-2004 CHAPTER 1, SECTION 106.1.1
	INFORMATION ON CONSTRUCTION DOCUMENTS. CONSTRUCTION
	DOCUMENTS SHALL BE OF SUFFICIENT CLARITY TO INDICATE
	THE LOCATION, NATURE AND EXTENT OF THE WORK PROPOSED
	AND SHOW IN DETAIL THAT IT WILL CONFORM TO THE
	PROVISIONS OF THIS CODE AND RELAVENT LAWS, ORDINANCES,
	RULES AND REGULATIONS, AS DETERMINED BY THE BUILDING
	OFFICIAL.

	2. PER FBC-2004 CHAPTER 1, SECTION 106.3.5.4
	RESIDENTIAL (ONE AND TWO-FAMILY) PLEASE SUBMIT A
	PLUMBING SANITARY ISOMETRIC RISER DIAGRAM THAT REFLECTS
	THE FLOOR PLAN INDICATING ALL WASTE, VENTS, TRAPS AND
	SIZES WITH CLEANOUT LOCATIONS.
	NOTE: EACH THREE STORY TOWNHOUSE WILL REQUIRE ITS OWN
	SANITARY ISOMETRIC RISER DIAGRAM.

	END OF COMMENTS:

	REVIEW BY MIKE PERSON
	(561) 805-6730
	FAX (561) 805-6731
	E-MAIL [email protected]
	UNDER SUPERVISION OF K.STEVENS
	(561) 805-6721

Review Stop	Z			ZONING
Rev No	1	Status	F	Date	2007-06-04			Cont ID
Sent By	choops			Date	2007-06-04	Time	14:47	Rev Time	0.00
Received By	choops			Date	2007-06-04	Time	14:47	Sent To	E

Notes

2007-06-04 15:04:00	*FAILED*


	1)PLEASE PROVIDE 2 COPIES OF AN UPDATED SURVEY
	(WITHIN THE LAST YEAR) , SHOWING THE SCOPE OF WORK,
	DIMENSIONS, AND SETBACK DIMENSIONS TO PROPERTY LINES.

	2)LOT AREA MUST BE AT LEAST 9,000 SQUARE FEET FOR 3
	UNITS.

	3)REQUIRED SIDE SETBACKS ARE 5 FT. MINIMUM WITH A
	TOTAL OF 15 FT..PROPOSED SIDE SETBACKS ONLY TOTAL 10
	FT.

	4)OVERALL BUILDING ELEVATION TO BE MEASURED FROM
	GRADE TO THE MIDPOINT OF THE ROOF'S PITCH.ALL OTHER
	ELEVATIONS TO BE MEASURED FROM GRADE AS WELL.

	5)PLEASE PROVIDE OVERHANG DIMENSIONS FROM WALL TO
	ROOF'S OUTERMOST POINT.

	6)POOLS REQUIRE A SEPERATE PERMIT, AND MUST BE FULLY
	ENCLOSED BY A FENCE.

	7)PLEASE SHOW ANY PROPOSED MECHANICAL AND/OR A/C
	EQUIPMENT ON SURVEYS AND SITE PLANS WITH SETBACK
	DIMENSIONS TO PROPERTY LINES.

	8)SHOW DRIVEWAY DIMENSIONS IF TO BE INCLUDED WITH
	THIS PERMIT.IF NOT DRIVEWAYS TO BE UNDER SEPERATE
	PERMIT.

	9)PLEASE PROVIDE A LANDSCAPE PLAN SHOWING COMPLIANCE
	WITH SECTION 94-442 OF THE ZONING AND LAND DEVELOPMENT
	REGULATIONS FOR THE CITY OF WEST PALM BEACH.


	CHRIS HOOPS
	ZONING TECHNICIAN
	561-805-6720