Home Records and Reports Contractor Records Owner Records Permit Records Permit Reports Business Reports Property Records Business Tax My Account Code Enforcement Contact Us Log In/Out Print Plan Review Stops For Permit 06101156 Review Stop B BUILDING (STRUCTURAL) Rev No 8 Status P Date 2010-09-13 Cont ID   Sent By dwise Date 2010-09-13 Time 15:40 Rev Time 0.00 Received By dwise Date 2010-09-13 Time 15:40 Sent To   Notes 2010-09-13 15:41:36 APPROVED WITH PROVISO BY R. MCDOUGAL ON 12/15/2009 Review Stop B BUILDING (STRUCTURAL) Rev No 7 Status F Date 2009-12-15 Cont ID   Sent By rmcdouga Date 2009-12-15 Time 12:07 Rev Time 0.00 Received By rmcdouga Date 2009-12-15 Time 07:50 Sent To   Notes 2009-12-15 16:08:00 REVISION REQUIRED THE FOLLOWING ITEMS HAVE BEEN DEEMED   DEFICIENT OR WERE NOTED TO BE MISSING UPON REVIEW:       1) TRUSS DRAWINGS AND LAYOUT SIGNED SEALED AND DATED BY   THE TRUSS ENGINEER AND REVIEWED BY THE DESIGNER OF   RECORD OF THE STRUCTURE. MUST BE REVIEWED AND APPROVED   PRIOR TO INSTALLATION. FBC 106.3.5       2) TWO COPIES OF A KEY PLAN AND INSTALLATION SCHEDULE   FOR THE ACCORDION SHUTTERS. SPECIFY THE OPENING   LOCATIONS OF THE SHUTTERS, THE MOUNT TYPE, SPANS,   FASTENERS, FASTENER SPACING, ETC. FBC 1609.1.2 NOTE: IF   ALL OF THE REQUIRED INFORMATION IS SUBMITTED WITH THIS   PERMIT THE SHUTTERS WILL BE INCLUDED WITH THIS PERMIT.   IF NOT, A SEPARATE PERMIT AND FEES WILL BE REQUIRED AND   THE C.O. WILL NOT BE ISSUED UNTIL THEY HAVE BEEN   INSTALLED AND APPROVED.       3) TWO COPIES OF PRODUCT APPROVALS FOR THE BULLET   RESISTANT WINDOWS AND PAYMENT DRAWER ASSEMBLIES, THE   ROOFING MATERIALS AND THE WALL MOUNTED LOUVER VENTS FOR   ATTIC VENTILATION. DCA RULE 9B-72       4) THE GLASS TYPE, MULLION TYPE AND ANCHOR TYPE OF THE   STOREFRONT WINDOWS. THIS INFORMATION DETERMINES THE   DESIGN PRESSURES FOR THE ASSEMBLIES. FBC 1604.9 THIS   INFORMATION CAN BE PROVIDED WITH THE SHOP DRAWINGS FROM   THE WINDOW COMPANY. THEY WILL NEED TO BE SUBMITTED AND   APPROVED PRIOR TO INSTALLATION.       5) THE HINGE OPTION AND IF THE STOREFRONT DOOR IS   REINFORCED OR NOT. THIS INFORMATION DETERMINES DESIGN   PRESSURES FOR THE ASSEMBLY. FBC 1604.9 THIS INFORMATION   CAN BE PROVIDED WITH THE SHOP DRAWINGS.             2009-12-15 14:49:05 TEMPORARY FAILED STATUS WILL REMAIN UNTIL A CONTRACTOR   IS DETERMINED. Review Stop B BUILDING (STRUCTURAL) Rev No 6 Status F Date 2009-09-29 Cont ID   Sent By rmcdouga Date 2009-09-29 Time 14:41 Rev Time 0.00 Received By rmcdouga Date 2009-09-29 Time 14:40 Sent To   Notes 2009-09-29 16:19:24 2007 FBC W/2009 REVISIONS   CONVENIENCE STORE WITH FUEL DISPENSING       DENIED BY BUILDING       1) ON SHEET S-1 THE COMPONENT AND CLADDING PRESSURES   ARE INCORRECT FOR EXPOSURE C WITH A 20' MEAN ROOF   HEIGHT. THE ONES LISTED ARE EXPOSURE 'B' PRESSURES.   PLEASE CORRECT. FBC 1609.4.1       2) ON SHEET S-2 THE NOTES AT THE BOTTOM OF THE PAGE   LIST THE MEAN ROOF HEIGHT AS 30' AND THE BASIC WIND   PRESSURE AS 29.85 PSF. THESE ARE INCORRECT. THE MEAN   ROOF HEIGHT IS SPECIFIED AS 20' AND THE BASIC WIND   PRESSURE FOR EXPOSURE C AS 38.38 ON SHEET S-1. PLEASE   CORRECT. FBC 1609       3) SUBMIT TRUSS DRAWINGS AND LAYOUT SIGNED SEALED AND   DATED BY THE TRUSS ENGINEER AND REVIEWED BY THE   DESIGNER OF RECORD OF THE STRUCTURE. MUST BE REVIEWED   AND APPROVED PRIOR TO INSTALLATION. FBC 106.3.5       4) SUBMIT TWO COPIES OF A KEY PLAN AND INSTALLATION   SCHEDULE FOR THE ACCORDION SHUTTERS. SPECIFY THE   OPENING LOCATIONS OF THE SHUTTERS, THE MOUNT TYPE,   SPANS, FASTENERS, FASTENER SPACING, ETC. FBC 1609.1.2   NOTE: IF ALL OF THE REQUIRED INFORMATION IS SUBMITTED   WITH THIS PERMIT THE SHUTTERS WILL BE INCLUDED WITH   THIS PERMIT. IF NOT, A SEPARATE PERMIT AND FEES WILL BE   REQUIRED AND THE C.O. WILL NOT BE ISSUED UNTIL THEY   HAVE BEEN INSTALLED AND APPROVED.       5) SUBMIT TWO COPIES OF PRODUCT APPROVALS FOR THE   BULLET RESISTANT WINDOWS AND PAYMENT DRAWER ASSEMBLIES.   DCA RULE 9B-72       6) ON THE PRODUCT APPROVALS FOR THE STOREFRONT WINDOWS,   SPECIFY THE GLASS TYPE, MULLION TYPE AND ANCHOR TYPE BY   CIRCLING THE APPROPRIATE ITEMS IN THE TABLES. THIS   INFORMATION DETERMINES THE DESIGN PRESSURES FOR THE   ASSEMBLIES. FBC 1604.9 THIS INFORMATION CAN BE PROVIDED   WITH THE SHOP DRAWINGS FROM THE WINDOW COMPANY. THEY   WILL NEED TO BE SUBMITTED AND APPROVED PRIOR TO   INSTALLATION.       7) ON THE PRODUCT APPROVALS FOR THE STOREFRONT DOOR   SPECIFY THE HINGE OPTION AND IF REINFORCED OR NOT. THIS   INFORMATION DETERMINES DESIGN PRESSURES FOR THE   ASSEMBLY. FBC 1604.9 THIS INFORMATION CAN ALSO BE   PROVIDED WITH THE SHOP DRAWINGS.       8) SUBMIT TWO COPIES OF PRODUCT APPROVALS FOR THE   ROOFING MATERIALS AND THE WALL MOUNTED LOUVER VENTS FOR   ATTIC VENTILATION. DCA RULE 9B-72       9) PLEASE RESPOND TO COMMENTS IN WRITING.       ROBERT MCDOUGAL   BLDG. PLAN REVIEW   (561)805-6714   [email protected] Review Stop B BUILDING (STRUCTURAL) Rev No 5 Status F Date 2009-07-24 Cont ID   Sent By rmcdouga Date 2009-07-24 Time 14:26 Rev Time 0.00 Received By rmcdouga Date 2009-07-24 Time 14:26 Sent To   Notes 2009-07-24 12:22:54 2007 FBC W/2009 REVISIONS   CONVENIENCE STORE WITH FUEL DISPENSING       DENIED BY BUILDING       1) ON SHEET S-1 AND THE TOP OF SHEET S-2 THE EXPOSURE   CATEGORY IS CORRECTLY SPECIFIED AS 'C'. HOWEVER, AT THE   BOTTOM OF SHEET S-2 THE EXPOSURE 'B' IS SPECIFIED ON   THE ROOF ZONE DETAIL. PLEASE CORRECT. FBC 1609.4.1       2) THE COMPONENT AND CLADDING PRESSURES ON SHEET A-5 DO   NOT CORRESPOND WITH THOSE ON SHEET S-1. THE PRESSURES   ON A-5 ARE FOR EXPOSURE CATEGORY 'B'. PLEASE CORRECT.   FBC 1609       3) SUBMIT TRUSS DRAWINGS AND LAYOUT SIGNED SEALED AND   DATED BY THE TRUSS ENGINEER AND REVIEWED BY THE   DESIGNER OF RECORD OF THE STRUCTURE. MUST BE REVIEWED   AND APPROVED PRIOR TO INSTALLATION. FBC 106.3.5       4) SHEET A-1 AND S-2 OF THE PLANS SPECIFY IMPACT   WINDOWS AND NO SHUTTERS. HOWEVER, THE PRODUCT APPROVALS   THAT WERE SUBMITTED FOR THE STOREFRONTS ARE NOT IMPACT   RATED AND PRODUCT APPROVALS FOR ACCORDION SHUTTERS WERE   SUBMITTED. PLEASE CLARIFY. FBC 1609.1.2       5) SUBMIT TWO COPIES OF A KEY PLAN AND INSTALLATION   SCHEDULE FOR THE ACCORDION SHUTTERS. SPECIFY THE   OPENING LOCATIONS OF THE SHUTTERS, THE MOUNT TYPE,   SPANS, FASTENERS, FASTENER SPACING, ETC. FBC 1609.1.2       6) SUBMIT TWO COPIES OF PRODUCT APPROVALS FOR THE   BULLET RESISTANT WINDOWS AND PAYMENT DRAWER ASSEMBLIES.   DCA RULE 9B-72       7) ON THE PRODUCT APPROVALS FOR THE STOREFRONT WINDOWS,   SPECIFY THE GLASS TYPE, MULLION TYPE AND ANCHOR TYPE BY   CIRCLING THE APPROPRIATE ITEMS IN THE TABLES. THIS   INFORMATION DETERMINES THE DESIGN PRESSURES FOR THE   ASSEMBLIES. FBC 1604.9       8) ON THE PRODUCT APPROVALS FOR THE STOREFRONT DOOR   SPECIFY THE HINGE OPTION AND IF REINFORCED OR NOT. THIS   INFORMATION DETERMINES DESIGN PRESSURES FOR THE   ASSEMBLY. FBC 1604.9       9) SUBMIT TWO COPIES OF PRODUCT APPROVALS FOR THE   ROOFING MATERIALS AND THE WALL MOUNTED LOUVER VENTS FOR   ATTIC VENTILATION. DCA RULE 9B-72       ROBERT MCDOUGAL   BLDG. PLAN REVIEW   (561)805-6714   [email protected] Review Stop B BUILDING (STRUCTURAL) Rev No 4 Status F Date 2009-06-02 Cont ID   Sent By rmcdouga Date 2009-06-02 Time 13:37 Rev Time 0.00 Received By rmcdouga Date 2009-06-02 Time 13:37 Sent To   Notes 2009-06-02 14:54:26 2007 FBC W/2009 REVISIONS   CONVENIENCE STORE WITH FUEL DISPENSING           DENIED BY BUILDING       1) IMPACT FEES MUST BE PAID TO PALM   BEACH COUNTY, PLANS STAMPED BY THEM AND   COPY OF RECEIPT SUBMITTED TO CITY OF   WEST PALM BEACH BUILDING DEPARTMENT,   BEFORE A BUILDING PERMIT CAN BE ISSUED.       2) THE CODE THAT IS CURRENTLY IN EFFECT IS THE 2007   FLORIDA BUILDING CODE WITH 2009 SUPPLEMENT. PLEASE   CORRECT CODE NOTE ON SHEET SP-1.       3) SPECIFY THE REQUIRED SOIL BEARING CAPACITY ON THE   PLANS. FBC 1804.1       4) PLEASE UPDATE THE STANDARDS SPECIFIED ON SHEETS S-1   AND S-2 TO THE EDITIONS SPECIFIED IN CHAPTER 35 OF THE   2007 FBC. ASCE 7-05, ACI 318-05, ACI 315-05, TMS 402-05   AND TMS 602-05.       5) SUBMIT TWO COPIES OF PRODUCT APPROVALS FOR THE   EXTERIOR WINDOWS, DOORS, STOREFRONTS, MULLIONS, ROOFING   MATERIAL, TRUSS CONNECTORS, IMPACT PROTECTION PRODUCTS,   ETC. AS REQUIRED BY FAC RULE 9B-72.       6) SUBMIT TRUSS DRAWINGS AND LAYOUT SIGNED, SEALED AND   DATED BY THE TRUSS ENGINEER AND REVIEWED AND APPROVED   BY THE DESIGNER OF RECORD FOR THE STRUCTURE. FBC   106.3.5* CITY AMENDMENTS. NOTE: THE UPLIFT AT HIP   GIRDER TRUSSES MAY EXCEED 1500#.       7) SPECIFY THE REQUIRED SOIL BEARING CAPACITY ON THE   PLANS. FBC 1804.1.       8) THE ROOF VENTILATION NOTE ON A-4 SITES EXCEPTION #2   TO FBC 1203.2. THIS EXCEPTION APPLIES TO UN-VENTED   ATTICS SUCH AS THOSE USING SPRAY FOAM INSULATION   APPLIED TO THE UNDERSIDE OF THE ROOF DECK. THE PLANS DO   NOT INDICATE THIS TYPE OF ATTIC. SHOW COMPLIANCE WITH   FBC 1203.2.       9) 2603.4.1.3 WALK -IN COOLERS .   IN NONSPRINKLERED BUILDINGS, FOAM PLASTIC HAVING A   THICKNESS THAT DOES NOT EXCEED 4 INCHES (102 MM) AND A   MAXIMUM FLAME SPREAD INDEX OF 75 IS PERMITTED IN WALK   -IN COOLERS OR FREEZER UNITS WHERE THE AGGREGATE FLOOR   AREA DOES NOT EXCEED 400 SQUARE FEET (37 M 2 ) AND THE   FOAM PLASTIC IS COVERED BY A METAL FACING NOT LESS THAN   0.032-INCH-THICK (0.81 MM) ALUMINUM OR   CORROSION-RESISTANT STEEL HAVING A MINIMUM BASE METAL   THICKNESS OF 0.016 INCH (0.41 MM). A THICKNESS OF UP TO   10 INCHES (254 MM) IS PERMITTED WHERE PROTECTED BY A   THERMAL BARRIER. THE WALK-IN COOLER SHOWN ON THE PLANS   APPEARS TO BE LARGER THAN THE 400 SQFT ALLOWED. SHOW   HOW WALK-IN COOLER COMPLIES. PROVIDE MANUFACTURER'S   SPECIFICATIONS AND DETAILS.       10) DOOR #S 3 AND 5 DO NOT HAVE THE MANEUVERING   CLEARANCES REQUIRED BY FBC 11-4.13.6. A MINIMUM OF 18"   IS REQUIRED ON THE PULL SIDE AT THE LATCH OF SIDE SWING   DOORS.       11) AS NOTED ON THE PLAN A SEPARATE PERMIT WILL BE   REQUIRED FOR THE STAND ALONE CANOPY AT GAS PUMPS.       12) THE LIFE SAFETY PLAN DOES NOT INDICATE THE TRAVEL   DISTANCE FROM INSIDE THE WALK-IN COOLER TO THE ONE   EXIT. THIS APPEARS TO BE A TRAVEL DISTANCE IN EXCESS OF   75 FT, WHICH WOULD REQUIRE TWO EXITS. FBC 1019.2 AND   1015.1       13) ON LS-1, THE OCCUPANT LOAD FOR THE WALK-IN COOLER   SHOULD BE INCLUDED IN THE TABLE AS A STORAGE OCCUPANCY.   FBC TABLE 1004.1.1 AND TABLE 508.3       14) THE WEST EXTERIOR WALL THAT IS LOCATED AT 6 FT FROM   THE PROPERTY LINE IS REQUIRED TO HAVE A ONE HOUR FIRE   RATING PER FBC TABLE 602. THE MAXIMUM AREA OF EXTERIOR   WALL OPENINGS IS 10 PERCENT PER TABLE 704.8. PLEASE   NOTE THIS ON PLANS.       NOTE: FOR THE NORTH OR REAR WALL WHICH IS LOCATED ON AN   ALLEY, THE FIRE SEPARATION DISTANCE IS MEASURED FROM   THE FACE OF THE BUILDING TO THE CENTERLINE OF THE   ALLEY, WHICH IS 16 FEET BASED ON THE SITE PLAN. THIS   WALL IS NOT REQUIRED TO BE FIRE RATED BY TABLE 602 AND   FOOTNOTE I OF TABLE 704.8 ALLOWS UNLIMITED UNPROTECTED   OPENINGS.       NOTE: ADDITIONAL COMMENTS MAY RESULT WHEN THESE   COMMENTS ARE ADDRESSED, DUE TO THE AMOUNT OF MISSING   INFORMATION.       ROBERT MCDOUGAL   BLDG. PLAN REVIEW   (561)805-6714 Review Stop B BUILDING (STRUCTURAL) Rev No 3 Status F Date 2007-11-14 Cont ID   Sent By rmcdouga Date 2007-11-14 Time 10:41 Rev Time 0.00 Received By rmcdouga Date 2007-11-13 Time 17:33 Sent To   Notes 2007-11-14 11:46:58 2004 FBC   CONSTRUCT NEW CONVENIENCE STORE (PLAN REVIEW)       DENIED BY BUILDING       1) IMPACT FEES MUST BE PAID TO PALM   BEACH COUNTY, PLANS STAMPED BY THEM AND   COPY OF RECEIPT SUBMITTED TO CITY OF   WEST PALM BEACH BUILDING DEPARTMENT,   BEFORE A BUILDING PERMIT CAN BE ISSUED.       2)A RECORDED COPY OF THE NOTICE OF COMMENCEMENT   MUST BE SUBMITTED BEFORE A   PERMIT CAN BE ISSUED.       3) COMPLIED.       4) COMPLIED.       5) FBC SECTION 1603.1.2 THAT WAS SPECIFIED UNDER DESIGN   PARAMETERS ON SHEETS A2 AND A7 IS NOT THE APPROPRIATE   SECTION. PLEASE CORRECT. SPECIFY CHAPTER 16.       6) COMPLIED.       7) PROVIDESURVEY/SITE PLANS INDICATING THE LOCATION   OF THE STRUCTURE, DISTANCE TO PROPERTY LINES, DISTANCES   TO OTHER STRUCTURES ON THE PROPERTY FOR DETERMINING   FIRE SEPARATION DISTANCES. SEE FBC 702, 704.8 AND TABLE   602. THE SURVEY THAT WAS SUBMITTED DOES NOT CORRESPOND   WITH THE SITE PLANS. THE SITE PLAN IS NOT SIGNED AND   SEALED.       8)SUBMIT ENERGY CALCULATIONS FOR THE STRUCTURE AS   REQUIRED BY FBC 13-4.       9)SUBMIT PRODUCT APPROVALS FOR THE EXTERIOR WINDOWS,   DOORS, STOREFRONTS, MULLIONS, ROOFING MATERIAL, IMPACT   PROTECTION PRODUCTS, ETC.   PRODUCT APPROVALS SUBMITTED WITH   PERMIT APPLICATION AFTER OCTOBER 1, 2003   ARE REQUIRED TO COMPLY WITH THE FLORIDA   PRODUCT APPROVAL SYSTEM. FOR INFORMATION   PLEASE SEE THE STATE WEBSITE AT   WWW.FLORIDABUILDING.ORG. PRODUCTS WITH   STATEWIDE APPROVAL ARE REQUIRED TO BE   SUBMITTED WITH A COVER SHEET THAT LISTS   THE PRODUCT IDENTITY NUMBER FROM THE   STATE.       10)WPB ADMIN CODE 106.3* PRODUCT   APPROVALS. THOSE PRODUCT WHICH ARE   REGULATED BY DCA RULE 9B-72 SHALL BE   REVIEWED AND APPROVED IN WRITING BY THE   DESIGNER OF RECORD PRIOR TO SUBMITTAL   FOR JURISDICTIONAL APPROVAL.       11) SPECIFY HOW IMPACT PROTECTION OF OPENINGS WILL BE   PROVIDED AS REQUIRED BY FBC 1609.1.4. IF STORM PANELS   ARE TO BE USED, SUBMIT 2 COPIES OF PRODUCT APPROVALS, A   KEY PLAN AND INSTALLATION SCHEDULE. SPECIFY THE MOUNT   TYPE, ANCHORS, ANCHOR SPACING, ETC.       12) SUBMIT TRUSS DRAWINGS AND LAYOUT SIGNED, SEALED AND   DATED BY THE TRUSS ENGINEER AND REVIEWED AND APPROVED   BY THE DESIGNER OF RECORD OF THE STRUCTURE. FBC   106.3.5* CITY AMENDMENTS. NOTE: THE UPLIFT AT HIP   GIRDER TRUSSES MAY EXCEED 1500#.       13)SPECIFY THE ANCHOR TYPE, SIZE, EMBED DEPTH AND   SIZE OF THE HOLES FOR THE ANCHORS FOR THE STEEL COLUMN   BASE. SPECIFY THE WELD TYPE FOR THE COLUMN TO BASE   ATTACHMENT. PROVIDE A DETAIL SPECIFYING THE COLUMN CAP   FOR THE STEEL COLUMNS WITH FASTENERS, WELDS, ETC.   INDICATED. THE STEEL COLUMN THICKNESS ON A-3 IS NOT   LEGIBLE.       14) COMPLIED.       15)COMPLIED.       16) THE ROOF ZONE FIGURE FOR THE HIP ROOF ON A7 IS   INCORRECT. THE OUTSIDE CORNER AREAS OF THE HIP ROOF ARE   ZONE 3 . SEE FBC FIGURE 1609.6.2.2 W/2006 REVISIONS   (REVISED SHEETS).       17)SHOW HOW WALK-IN COOLER COMPLIES WITH 2603.4   THERMAL BARRIER. PROVIDE MANUFACTURER'S SPECIFICATIONS   AND DETAILS.   EXCEPT AS PROVIDED FOR IN SECTIONS 2603.4.1 AND 2603.8   , FOAM PLASTIC SHALL BE SEPARATED FROM THE INTERIOR OF   A BUILDING BY AN APPROVED THERMAL BARRIER OF 0.5-INCH   (12.7 MM) GYPSUM WALLBOARD OR EQUIVALENT THERMAL   BARRIER MATERIAL THAT WILL LIMIT THE AVERAGE   TEMPERATURE RISE OF THE UNEXPOSED SURFACE TO NOT MORE   THAN 250 DEGREES F (120 DEGREES C) AFTER 15 MINUTES OF   FIRE EXPOSURE, COMPLYING WITH THE STANDARD   TIME-TEMPERATURE CURVE OF ASTM E 119. THE THERMAL   BARRIER SHALL BE INSTALLED IN SUCH A MANNER THAT IT   WILL REMAIN IN PLACE FOR 15 MINUTES BASED ON FM 4880,   UL 1040, NFPA 286 OR UL 1715. COMBUSTIBLE CONCEALED   SPACES SHALL COMPLY WITH SECTION 717 .   2603.4.1 THERMAL BARRIER NOT REQUIRED.   THE THERMAL BARRIER SPECIFIED IN SECTION 2603.4 IS NOT   REQUIRED UNDER THE CONDITIONS SET FORTH IN SECTIONS   2603.4.1.1 THROUGH 2603.4.1.13 .   2603.4.1.2 COOLER AND FREEZER WALLS.   FOAM PLASTIC INSTALLED IN A MAXIMUM THICKNESS OF 10   INCHES (254 MM) IN COOLER AND FREEZER WALLS SHALL: 1.   HAVE A FLAME SPREAD INDEX OF 25 OR LESS AND A   SMOKE-DEVELOPED INDEX OF NOT MORE THAN 450, WHERE   TESTED IN A MINIMUM 4 INCH (102 MM) THICKNESS.   2.HAVE FLASH IGNITION AND SELF-IGNITION   TEMPERATURES OF NOT LESS THAN 600 DEGREES F AND 800   DEGREES F (316 DEGREES C AND 427 DEGREES C),   RESPECTIVELY.   3.HAVE A COVERING OF NOT LESS THAN 0.032-INCH (0.8   MM) ALUMINUM OR CORROSION-RESISTANT STEEL HAVING A BASE   METAL THICKNESS NOT LESS THAN 0.0160 INCH (0.4 MM) AT   ANY POINT.   4.BE PROTECTED BY AN AUTOMATIC SPRINKLER SYSTEM.   WHERE THE COOLER OR FREEZER IS WITHIN A BUILDING, BOTH   THE COOLER OR FREEZER AND THAT PART OF THE BUILDING IN   WHICH IT IS LOCATED SHALL BE SPRINKLERED.   WALK IN COOLERS   2603.4.1.3 WALK -IN COOLERS .   IN NONSPRINKLERED BUILDINGS, FOAM PLASTIC HAVING A   THICKNESS THAT DOES NOT EXCEED 4 INCHES (102 MM) AND A   MAXIMUM FLAME SPREAD INDEX OF 75 IS PERMITTED IN WALK   -IN COOLERS OR FREEZER UNITS WHERE THE AGGREGATE FLOOR   AREA DOES NOT EXCEED 400 SQUARE FEET (37 M 2 ) AND THE   FOAM PLASTIC IS COVERED BY A METAL FACING NOT LESS THAN   0.032-INCH-THICK (0.81 MM) ALUMINUM OR   CORROSION-RESISTANT STEEL HAVING A MINIMUM BASE METAL   THICKNESS OF 0.016 INCH (0.41 MM). A THICKNESS OF UP TO   10 INCHES (254 MM) IS PERMITTED WHERE PROTECTED BY A   THERMAL BARRIER.   SHOW HOW WALK-IN COOLER COMPLIES. PROVIDE   MANUFACTURER'S SPECIFICATIONS AND DETAILS.       18) SUBMIT SITE PLANS SHOWING ACCESSIBLE PARKING,   ACCESSIBLE ROUTE TO THE BUILDING ENTRANCE, RAMPS, CURB   CUTS, ETC. AS REQUIRED BY FBC 11-4.1.3. THE PLAN WITH   THIS INFORMATION IS REQUIRED TO BE SIGNED AND SEALED BY   A FLORIDA LICENSED ARCHITECT OR ENGINEER. SEE FS 471   AND 481.       19) COMPLIED.       20)COMPLIED.       21) COMPLIED.       22) COMPLIED.       23) COMPLIED.       24) COMPLIED.       25) A SEPARATE PERMIT WILL BE REQUIRED FOR THE STAND   ALONE CANOPY AT GAS PUMPS.       26) COMPLIED.       27) ADDITIONAL COMMENTS MAY RESULT WHEN THESE COMMENTS   ARE ADDRESSED, DUE TO THE AMOUNT OF MISSING   INFORMATION.       28) SPECIFY THE WIDTH OF THE STRUCTURE ON THE PLANS.   FBC 106.1* CITY AMENDMENTS       ROBERT MCDOUGAL   BLDG. PLAN REVIEW   (561)805-6714   [email protected] Review Stop B BUILDING (STRUCTURAL) Rev No 2 Status F Date 2007-03-28 Cont ID   Sent By rmcdouga Date 2007-03-28 Time 14:25 Rev Time 0.00 Received By rmcdouga Date 2007-03-28 Time 11:24 Sent To   Notes 2007-03-28 14:24:55 DENIED BY BUILDING       1) IMPACT FEES MUST BE PAID TO PALM   BEACH COUNTY, PLANS STAMPED BY THEM AND   COPY OF RECEIPT SUBMITTED TO CITY OF   WEST PALM BEACH BUILDING DEPARTMENT,   BEFORE A BUILDING PERMIT CAN BE ISSUED.       2)A RECORDED COPY OF THE NOTICE OF COMMENCEMENT   MUST BE SUBMITTED BEFORE A   PERMIT CAN BE ISSUED.       3) THE CODE THAT IS CURRENTLY IN EFFECT IS THE 2004   FLORIDA BUILDING CODE. PLEASE CORRECT GENERAL NOTE #1   ON SHEET A-1.       4) THE WRONG EDITION OF ASCE 7 IS SPECIFIED UNDER   DESIGN PARAMETERS ON SHEETS A2 AND A7. THE EDITION   REFERENCED BY THE 2004 FBC IS ASCE 7-02. PLEASE   CORRECT.       5) FBC SECTION 1606.1.7 THAT WAS SPECIFIED UNDER DESIGN   PARAMETERS ON SHEETS A2 AND A7 IS NO LONGER IN THE   CODE. PLEASE CORRECT.       6) SPECIFY THE OCCUPANCY TYPE. SEE FBC 302.1.       7) PROVIDESURVEY/SITE PLANS INDICATING THE LOCATION   OF THE STRUCTURE, DISTANCE TO PROPERTY LINES, DISTANCES   TO OTHER STRUCTURES ON THE PROPERTY FOR DETERMINING   FIRE SEPARATION DISTANCES. SEE FBC 702, 704.8 AND TABLE   602.       8)SUBMIT ENERGY CALCULATIONS FOR THE STRUCTURE AS   REQUIRED BY FBC 13-4.       9)SUBMIT PRODUCT APPROVALS FOR THE EXTERIOR WINDOWS,   DOORS, STOREFRONTS, MULLIONS, ROOFING MATERIAL, IMPACT   PROTECTION PRODUCTS, ETC.   PRODUCT APPROVALS SUBMITTED WITH   PERMIT APPLICATION AFTER OCTOBER 1, 2003   ARE REQUIRED TO COMPLY WITH THE FLORIDA   PRODUCT APPROVAL SYSTEM. FOR INFORMATION   PLEASE SEE THE STATE WEBSITE AT   WWW.FLORIDABUILDING.ORG. PRODUCTS WITH   STATEWIDE APPROVAL ARE REQUIRED TO BE   SUBMITTED WITH A COVER SHEET THAT LISTS   THE PRODUCT IDENTITY NUMBER FROM THE   STATE.       10)WPB ADMIN CODE 106.3* PRODUCT   APPROVALS. THOSE PRODUCT WHICH ARE   REGULATED BY DCA RULE 9B-72 SHALL BE   REVIEWED AND APPROVED IN WRITING BY THE   DESIGNER OF RECORD PRIOR TO SUBMITTAL   FOR JURISDICTIONAL APPROVAL.       11) SPECIFY HOW IMPACT PROTECTION OF OPENINGS WILL BE   PROVIDED AS REQUIRED BY FBC 1609.1.4.       12) SUBMIT TRUSS DRAWINGS AND LAYOUT SIGNED, SEALED AND   DATED BY THE TRUSS ENGINEER AND REVIEWED AND APPROVED   BY THE DESIGNER OF RECORD OF THE STRUCTURE. FBC   106.3.5* CITY AMENDMENTS. NOTE: THE UPLIFT AT HIP   GIRDER TRUSSES MAY EXCEED 1500#.       13) PROVIDE DIMENSIONS TO INDICATE THE LOCATIONS OF THE   STEEL COLUMNS SHOWN IN DETAIL 2 ON A-3 ON THE   FOUNDATION PLAN. SPECIFY THE ANCHOR TYPE, SIZE, EMBED   DEPTH AND SIZE OF THE HOLES FOR THE ANCHORS FOR THE   STEEL COLUMN BASE. SPECIFY THE WELD TYPE FOR THE COLUMN   TO BASE ATTACHMENT. PROVIDE A DETAIL SPECIFYING THE   COLUMN CAP FOR THE STEEL COLUMNS WITH FASTENERS, WELDS,   ETC. INDICATED.       14) SPECIFY THE LOCATION AND SIZE OF THE ATTIC ACCESS   REQUIRED BY FBC 1209.2.       15)WALL SECTION 1 ON A-4 SPECIFIES ASPHALT ROOF   SHINGLES AND THE ELEVATIONS SHOW A METAL ROOF. PLEASE   CORRECT.       16) THE ROOF ZONE FIGURE FOR THE HIP ROOF ON A7 IS   INCORRECT. THE OUTSIDE CORNER AREAS OF THE HIP ROOF ARE   ZONE 3 . SEE FBC FIGURE 1609.6.2.2 (REVISED SHEETS).       17)SHOW HOW WALK-IN COOLER COMPLIES WITH 2603.4   THERMAL BARRIER. PROVIDE MANUFACTURER'S SPECIFICATIONS   AND DETAILS.   EXCEPT AS PROVIDED FOR IN SECTIONS 2603.4.1 AND 2603.8   , FOAM PLASTIC SHALL BE SEPARATED FROM THE INTERIOR OF   A BUILDING BY AN APPROVED THERMAL BARRIER OF 0.5-INCH   (12.7 MM) GYPSUM WALLBOARD OR EQUIVALENT THERMAL   BARRIER MATERIAL THAT WILL LIMIT THE AVERAGE   TEMPERATURE RISE OF THE UNEXPOSED SURFACE TO NOT MORE   THAN 250 DEGREES F (120 DEGREES C) AFTER 15 MINUTES OF   FIRE EXPOSURE, COMPLYING WITH THE STANDARD   TIME-TEMPERATURE CURVE OF ASTM E 119. THE THERMAL   BARRIER SHALL BE INSTALLED IN SUCH A MANNER THAT IT   WILL REMAIN IN PLACE FOR 15 MINUTES BASED ON FM 4880,   UL 1040, NFPA 286 OR UL 1715. COMBUSTIBLE CONCEALED   SPACES SHALL COMPLY WITH SECTION 717 .   2603.4.1 THERMAL BARRIER NOT REQUIRED.   THE THERMAL BARRIER SPECIFIED IN SECTION 2603.4 IS NOT   REQUIRED UNDER THE CONDITIONS SET FORTH IN SECTIONS   2603.4.1.1 THROUGH 2603.4.1.13 .   2603.4.1.2 COOLER AND FREEZER WALLS.   FOAM PLASTIC INSTALLED IN A MAXIMUM THICKNESS OF 10   INCHES (254 MM) IN COOLER AND FREEZER WALLS SHALL: 1.   HAVE A FLAME SPREAD INDEX OF 25 OR LESS AND A   SMOKE-DEVELOPED INDEX OF NOT MORE THAN 450, WHERE   TESTED IN A MINIMUM 4 INCH (102 MM) THICKNESS.   2.HAVE FLASH IGNITION AND SELF-IGNITION   TEMPERATURES OF NOT LESS THAN 600 DEGREES F AND 800   DEGREES F (316 DEGREES C AND 427 DEGREES C),   RESPECTIVELY.   3.HAVE A COVERING OF NOT LESS THAN 0.032-INCH (0.8   MM) ALUMINUM OR CORROSION-RESISTANT STEEL HAVING A BASE   METAL THICKNESS NOT LESS THAN 0.0160 INCH (0.4 MM) AT   ANY POINT.   4.BE PROTECTED BY AN AUTOMATIC SPRINKLER SYSTEM.   WHERE THE COOLER OR FREEZER IS WITHIN A BUILDING, BOTH   THE COOLER OR FREEZER AND THAT PART OF THE BUILDING IN   WHICH IT IS LOCATED SHALL BE SPRINKLERED.   WALK IN COOLERS   2603.4.1.3 WALK -IN COOLERS .   IN NONSPRINKLERED BUILDINGS, FOAM PLASTIC HAVING A   THICKNESS THAT DOES NOT EXCEED 4 INCHES (102 MM) AND A   MAXIMUM FLAME SPREAD INDEX OF 75 IS PERMITTED IN WALK   -IN COOLERS OR FREEZER UNITS WHERE THE AGGREGATE FLOOR   AREA DOES NOT EXCEED 400 SQUARE FEET (37 M 2 ) AND THE   FOAM PLASTIC IS COVERED BY A METAL FACING NOT LESS THAN   0.032-INCH-THICK (0.81 MM) ALUMINUM OR   CORROSION-RESISTANT STEEL HAVING A MINIMUM BASE METAL   THICKNESS OF 0.016 INCH (0.41 MM). A THICKNESS OF UP TO   10 INCHES (254 MM) IS PERMITTED WHERE PROTECTED BY A   THERMAL BARRIER.   SHOW HOW WALK-IN COOLER COMPLIES. PROVIDE   MANUFACTURER'S SPECIFICATIONS AND DETAILS.       18) SUBMIT SITE PLANS SHOWING ACCESSIBLE PARKING,   ACCESSIBLE ROUTE TO THE BUILDING ENTRANCE, RAMPS, CURB   CUTS, ETC. AS REQUIRED BY FBC 11-4.1.3.       19) ALL DOORS ON THE ACCESSIBLE ROUTESARE REQUIRED TO   HAVE ADA COMPLIANT HARDWARE. SEE FBC 11-4.13.9.       20)SHOW THE REQUIRED CLEAR FLOOR SPACE AT THE WATER   CLOSET AND LAVATORY SPECIFY DIMENSIONS. SEE FBC   11-4.16.2 AND 11-4.19.3.       21) PROVIDE AN ACCESSIBLE COUNTER AS REQUIRED BY FBC   11-7.2.       22) DOOR 03DOES NOT HAVE THEMANEUVERING CLEARANCES   REQUIRED BY FBC 11-4.13.6. A MINIMUM OF 18" IS REQUIRED   ON THE PULL SIDE AT THE LATCH OF SIDE SWING DOORS.       23) FBC 11-4.16.3 REQUIRES THE HEIGHT OF WATER CLOSETS   TO BE 17" TO 19" MEASURED TO TOP OF THE TOILET SEAT.   PLEASE CORRECT DETAIL 5 ON A-4.       24) FBC 11-4.16.4 REQUIRES THE GRAB BAR BEHIND THE   WATER CLOSET TO BE 36" MINIMUM.       25) A SEPARATE PERMIT WILL BE REQUIRED FOR THE STAND   ALONE CANOPY AT GAS PUMPS.       26) THE FIRM'S LICENSE NUMBER IS REQUIRED TO BE IN THE   TITLE BLOCK ON EACH SHEET OF THE PLANS. SEE FS 481 AND   FAC 61G1-16.004.       27) ADDITIONAL COMMENTS MAY RESULT WHEN THESE COMMENTS   ARE ADDRESSED, DUE TO THE AMOUNT OF MISSING   INFORMATION.       ROBERT MCDOUGAL   BLDG. PLAN REVIEW   (561)805-6714 Review Stop B BUILDING (STRUCTURAL) Rev No 1 Status F Date 2006-11-15 Cont ID   Sent By rmcdouga Date 2006-11-15 Time 09:22 Rev Time 0.00 Received By rmcdouga Date 2006-11-15 Time 07:03 Sent To   Notes 2006-11-15 13:43:43 DENIED BY BUILDING       1) IMPACT FEES MUST BE PAID TO PALM   BEACH COUNTY, PLANS STAMPED BY THEM AND   COPY OF RECEIPT SUBMITTED TO CITY OF   WEST PALM BEACH BUILDING DEPARTMENT,   BEFORE A BUILDING PERMIT CAN BE ISSUED.       2) A RECORDED COPY OF THE NOTICE OF COMMENCEMENT MUST   BE SUBMITTED BEFORE A   PERMIT CAN BE ISSUED.       3) THE CODE THAT IS CURRENTLY IN EFFECT IS THE 2004   FLORIDA BUILDING CODE. PLEASE CORRECT GENERAL NOTE #1   ON SHEET A-1.       4) SPECIFY THE CONSTRUCTION TYPE BASED ON THE 2004 FBC   DESIGNATIONS. SPECIFY A OR B. SEE FBC TABLE 601.       5) SPECIFY THE OCCUPANCY TYPE. SEE FBC 302.1.       6) PROVIDE SURVEY/SITE PLANS INDICATING THE LOCATION OF   THE STRUCTURE, DISTANCE TO PROPERTY LINES, DISTANCES TO   OTHER STRUCTURES ON THE PROPERTY FOR DETERMINING FIRE   SEPARATION DISTANCES. SEE FBC 702, 704.8 AND TABLE 602.       7) PLEASE CLARIFY THE SCOPE OF WORK. THE APPLICATION   INDICATES THAT THIS IS A REMODEL OF AN EXISTING   BUILDING AND THE PLANS APPEAR TO BE FOR NEW   CONSTRUCTION.       8) IF THIS IS A REMODEL, SUBMIT A DEMO PLAN FOR THE   EXISTING STRUCTURE.       9) IF REMODEL, SPECIFY THE LEVEL OF ALTERATION FOR THE   WORK AS SPECIFIED IN THE 2004 FBC EXISTING BUILDING   CODE.       10) SUBMIT ENERGY CALCULATIONS FOR THE STRUCTURE AS   REQUIRED BY FBC 13-4.       11) SPECIFY THE DESIGN DATA FOR THE STRUCTURE REQUIRED   BY FBC 1603.1.4.       12) SUBMIT PRODUCT APPROVALS FOR THE EXTERIOR WINDOWS,   DOORS, STOREFRONTS, MULLIONS, ROOFING MATERIAL, IMPACT   PROTECTION PRODUCTS, ETC.   PRODUCT APPROVALS SUBMITTED WITH   PERMIT APPLICATION AFTER OCTOBER 1, 2003   ARE REQUIRED TO COMPLY WITH THE FLORIDA   PRODUCT APPROVAL SYSTEM. FOR INFORMATION   PLEASE SEE THE STATE WEBSITE AT   WWW.FLORIDABUILDING.ORG. PRODUCTS WITH   STATEWIDE APPROVAL ARE REQUIRED TO BE   SUBMITTED WITH A COVER SHEET THAT LISTS   THE PRODUCT IDENTITY NUMBER FROM THE   STATE.       13) WPB ADMIN CODE 106.3* PRODUCT   APPROVALS. THOSE PRODUCT WHICH ARE   REGULATED BY DCA RULE 9B-72 SHALL BE   REVIEWED AND APPROVED IN WRITING BY THE   DESIGNER OF RECORD PRIOR TO SUBMITTAL   FOR JURISDICTIONAL APPROVAL.       14) SPECIFY HOW IMPACT PROTECTION OF OPENINGS WILL BE   PROVIDED AS REQUIRED BY FBC 1609.1.4.       15) SUBMIT TRUSS DRAWINGS AND LAYOUT SIGNED, SEALED AND   DATED BY THE TRUSS ENGINEER AND REVIEWED AND APPROVED   BY THE DESIGNER OF RECORD OF THE STRUCTURE. FBC   106.3.5* CITY AMENDMENTS. NOTE: THE UPLIFT AT HIP   GIRDER TRUSSES MAY EXCEED 1500#.       16) INDICATE WHERE ON THE FOUNDATION PLAN THE STEEL   COLUMN IN DETAIL 2 ON A-3 IS LOCATED.       17) SPECIFY THE LOCATION AND SIZE OF THE ATTIC ACCESS   REQUIRED BY FBC 1209.2.       18) WALL SECTION 1 ON A-4 SPECIFIES ASPHALT ROOF   SHINGLES AND THE ELEVATIONS SHOW A METAL ROOF. PLEASE   CORRECT.       19) 2603.4 THERMAL BARRIER.   EXCEPT AS PROVIDED FOR IN SECTIONS 2603.4.1 AND 2603.8   , FOAM PLASTIC SHALL BE SEPARATED FROM THE INTERIOR OF   A BUILDING BY AN APPROVED THERMAL BARRIER OF 0.5-INCH   (12.7 MM) GYPSUM WALLBOARD OR EQUIVALENT THERMAL   BARRIER MATERIAL THAT WILL LIMIT THE AVERAGE   TEMPERATURE RISE OF THE UNEXPOSED SURFACE TO NOT MORE   THAN 250?F (120?C) AFTER 15 MINUTES OF FIRE EXPOSURE,   COMPLYING WITH THE STANDARD TIME-TEMPERATURE CURVE OF   ASTM E 119. THE THERMAL BARRIER SHALL BE INSTALLED IN   SUCH A MANNER THAT IT WILL REMAIN IN PLACE FOR 15   MINUTES BASED ON FM 4880, UL 1040, NFPA 286 OR UL 1715.   COMBUSTIBLE CONCEALED SPACES SHALL COMPLY WITH SECTION   717 .   2603.4.1 THERMAL BARRIER NOT REQUIRED.   THE THERMAL BARRIER SPECIFIED IN SECTION 2603.4 IS NOT   REQUIRED UNDER THE CONDITIONS SET FORTH IN SECTIONS   2603.4.1.1 THROUGH 2603.4.1.13 .   2603.4.1.2 COOLER AND FREEZER WALLS.   FOAM PLASTIC INSTALLED IN A MAXIMUM THICKNESS OF 10   INCHES (254 MM) IN COOLER AND FREEZER WALLS SHALL: 1.   HAVE A FLAME SPREAD INDEX OF 25 OR LESS AND A   SMOKE-DEVELOPED INDEX OF NOT MORE THAN 450, WHERE   TESTED IN A MINIMUM 4 INCH (102 MM) THICKNESS.   2. HAVE FLASH IGNITION AND SELF-IGNITION TEMPERATURES   OF NOT LESS THAN 600?F AND 800?F (316?C AND 427?C),   RESPECTIVELY.   3. HAVE A COVERING OF NOT LESS THAN 0.032-INCH (0.8 MM)   ALUMINUM OR CORROSION-RESISTANT STEEL HAVING A BASE   METAL THICKNESS NOT LESS THAN 0.0160 INCH (0.4 MM) AT   ANY POINT.   4. BE PROTECTED BY AN AUTOMATIC SPRINKLER SYSTEM. WHERE   THE COOLER OR FREEZER IS WITHIN A BUILDING, BOTH THE   COOLER OR FREEZER AND THAT PART OF THE BUILDING IN   WHICH IT IS LOCATED SHALL BE SPRINKLERED.   WALK IN COOLERS   2603.4.1.3 WALK -IN COOLERS .   IN NONSPRINKLERED BUILDINGS, FOAM PLASTIC HAVING A   THICKNESS THAT DOES NOT EXCEED 4 INCHES (102 MM) AND A   MAXIMUM FLAME SPREAD INDEX OF 75 IS PERMITTED IN WALK   -IN COOLERS OR FREEZER UNITS WHERE THE AGGREGATE FLOOR   AREA DOES NOT EXCEED 400 SQUARE FEET (37 M 2 ) AND THE   FOAM PLASTIC IS COVERED BY A METAL FACING NOT LESS THAN   0.032-INCH-THICK (0.81 MM) ALUMINUM OR   CORROSION-RESISTANT STEEL HAVING A MINIMUM BASE METAL   THICKNESS OF 0.016 INCH (0.41 MM). A THICKNESS OF UP TO   10 INCHES (254 MM) IS PERMITTED WHERE PROTECTED BY A   THERMAL BARRIER.   SHOW HOW WALK-IN COOLER COMPLIES. PROVIDE   MANUFACTURER'S SPECIFICATIONS AND DETAILS.       20) SUBMIT SITE PLANS SHOWING ACCESSIBLE PARKING,   ACCESSIBLE ROUTE TO THE BUILDING ENTRANCE, RAMPS, CURB   CUTS, ETC. AS REQUIRED BY FBC 11-4.1.3.       21) ALL DOORS ON THE ACCESSIBLE ROUTES ARE REQUIRED TO   HAVE ADA COMPLIANT HARDWARE. SEE FBC 11-4.13.9.       22) SHOW THE REQUIRED CLEAR FLOOR SPACE AT THE WATER   CLOSET AND LAVATORY SPECIFY DIMENSIONS. SEE FBC   11-4.16.2 AND 11-4.19.3.       23) PROVIDE AN ACCESSIBLE COUNTER AS REQUIRED BY FBC   11-7.2.       24) DOORS 03 AND 04 DO NOT HAVE THE MANEUVERING   CLEARANCES REQUIRED BY FBC 11-4.13.6. A MINIMUM OF 18"   IS REQUIRED ON THE PULL SIDE AT THE LATCH OF SIDE SWING   DOORS.       25) FBC 11-4.16.3 REQUIRES THE HEIGHT OF WATER CLOSETS   TO BE 17" TO 19" MEASURED TO TOP OF THE TOILET SEAT.   PLEASE CORRECT DETAIL 5 ON A-4.       26) FBC 11-4.16.4 REQUIRES THE GRAB BAR BEHIND THE   WATER CLOSET TO BE 36" MINIMUM.       27) A SEPARATE PERMIT WILL BE REQUIRED FOR THE STAND   ALONE CANOPY AT GAS PUMPS.       28) ADDITIONAL COMMENTS MAY RESULT WHEN THESE COMMENTS   ARE ADDRESSED, DUE TO THE AMOUNT OF MISSING   INFORMATION.       ROBERT MCDOUGAL   BLDG. PLAN REVIEW   (561)805-6714 Review Stop E ELECTRICAL Rev No 8 Status P Date 2010-09-13 Cont ID   Sent By dwise Date 2010-09-13 Time 15:47 Rev Time 0.00 Received By dwise Date 2010-09-13 Time 15:46 Sent To   Notes 2010-09-13 15:47:56 APPROVED BY DEWEY PALMER ON 12/9/2009 PENDING LICENSED   CONTRACTOR.DBW Review Stop E ELECTRICAL Rev No 7 Status F Date 2009-12-09 Cont ID   Sent By dpalmer Date 2009-12-09 Time 14:50 Rev Time 0.00 Received By dpalmer Date 2009-12-09 Time 14:50 Sent To   Notes 2009-12-09 14:51:17 STILL IN TEMPORARY FAILED STATUS UNTIL LICENSED   CONTRACTOR IS SIGNED ON PERMIT APPLICATION.   ELECTRICAL PLANS ALREADY STAMPED ON PREVIOUS REVIEW. Review Stop E ELECTRICAL Rev No 6 Status F Date 2009-12-09 Cont ID   Sent By dpalmer Date 2009-09-30 Time 14:33 Rev Time 0.00 Received By dpalmer Date 2009-09-30 Time 14:33 Sent To   Notes 2009-12-09 14:34:02 CONTRACTOR NOT YET SIGNED ON.   PLANS STAMPED. Review Stop E ELECTRICAL Rev No 5 Status F Date 2009-08-11 Cont ID   Sent By dpalmer Date 2009-08-11 Time 10:04 Rev Time 0.00 Received By dpalmer Date 2009-08-11 Time 10:04 Sent To   Notes 2009-08-11 10:04:15     ** DENIED REVIEW **       1) NOTE: PERMIT HAS NOT YET BEEN APPLIED FOR BY   LICENSED CONTRACTOR.       2) NOTE: THE SUBMITTED CALCULATIONS NEED TO INCLUDE ALL   EXTERIOR LIGHTING PER 13-415.AB.5, 13-415.AB.2.2. THIS   WAS A SPECIFIC NOTE ON THE PREVIOUS REVIEW YET THE SAME   ITEMS NEED TO BE ADDRESSED.       ** AS PERMIT HAS BEEN APPLIED UNDER PERMIT APPLICATION   AS *TBD* TO BE DETERMINED*, IF CALCULATIONS ARE   SUBMITTED BACK AGAIN WITH THE SAME ITEMS FS   553.80(2)(B)       3) NOTE: PLANS ARE STILL SHOWING SOME LOCATIONS IN   WHICH THERE ARE NOTES FOR 2008 GLITCHES TO THE 2007   FBC. THERE ARE ONLY 2009 SUPPLEMENTS TO THE 2007 FBC.       4) NOTE: PLEASE SUBMIT THE SPECS/MANUFACTURES CUT   SHEETS ON MANUAL TRANSFER SWITCH. COULD NOT LOCATE ON   THE SPECS SUBMITTED FOR THE DOUBLE THROW SWITCH AS THIS   BEING LISTED AS A MANUAL TRANSFER SWITCH? THIS IS   LEGALLY REQUIRED TRANSFER SWITCH PER STATUTES. IF THIS   EQUIPMENT IS LISTED AS SUCH PLEASE PROVIDE.   110.3,90.7,701.7, FS 526.143       ** PLANS ARE NO LONGER RELEASED PER BUILDING DIRECTOR.   A TIME WILL NEED TO BE SET UP TO BRING IN NEW REVISIONS   AND CHANGE OUT SHEETS.           IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]             Review Stop E ELECTRICAL Rev No 4 Status F Date 2009-05-29 Cont ID   Sent By dpalmer Date 2009-05-29 Time 08:28 Rev Time 0.00 Received By dpalmer Date 2009-05-29 Time 08:28 Sent To   Notes 2009-05-29 08:28:49 **DENIED 4TH REVIEW **               ** THIS IS THE FIRST REVIEW UNDER PERMIT APPLICATION   WHICH WAS ONLY MADE ON MAY 13, 2009       ** PLANS ARE ALSO UNDER A COMPLETELY NEW DESIGN TEAM.   ** SOME COMMENTS FROM PREVIOUS REVIEWS ALONG NOW WITH   SOME NEW COMMENTS BASED ON NEW PLANS AND DOCUMENTS   SUBMITTED.   PLEASE SEE NOTES BELOW.       1) NOTE: PLANS SUBMITTED AFTER MARCH 1ST, 2009 SHALL BE   UNDER NEW CODES. PLANS STATE THE NEW 2007 FBC HOWEVER   SOME REFERENCE 2008 GLITCHES AND SOME AREAS REFERENCE   20007 GLITCHES. BASED ON THE ADOPTED CODES AND GLITCHES   AS OF MARCH 1ST, 2009 THE CODE IS AS FOLLOWS.   2007 FBC WITH 2009 GLITCHES.   2005 NFPA-70 (ALREADY DONE)   2006 NFPA-101   2006 NFPA-1       2) NOTE: PLEASE BE SURE THE SUBMITTED ENERGY   CALCULATIONS COORDINATES WITH THE SUBMITTED PLANS.   PREVIOUS REVIEWS STATED COMMENTS TO OTHER DESIGN TEAMS   TO BE SURE THIS IS DONE.   13-415.AB.5       ** ONE EXAMPLE FOR METHOD *A* WHICH IS FOR *WHOLE*   BUILDING COMPLIANCE IS THE EXTERIOR LIGHTING. THE INPUT   DATA REPORT ONLY INCLUDES 7-32 WATT FIXTURES. HOW IS   THIS POSSIBLE WHEN THE PLANS CLEARLY INDICATE OTHER   FIXTURES SUCH AS CANOPY AND NEW SITE LIGHTING POLE   LIGHTS WITH WATTAGES EXCEEDING 250W.   PLEASE INCLUDE *ALL* FIXTURES ON PLANS AND LOCATION.       IF THERE ARE ANY QUESTIONS ON THIS COMMENT PLEASE BE   SURE TO CALL AND GO OVER WITH THIS PLANS EXAMINER.       3) NOTE: PLEASE SEE 422.13 WAS STORAGE TYPE WATER   HEATERS IN THE 2005 NEC ARE CONSIDERED CONTINUOUS LOADS   WITH RESPECT TO LOAD CALCULATIONS FOR FEEDERS AND   SERVICES.   THIS WAS A REVISION FROM THE PREVIOUS 2002 CODE WHICH   ONLY REQUIRED THE SIZING OF BRANCH CIRCUIT AND OCP TO   BE SET AT 125%.   PLEASE SEE COMMENTARY IN 2005 NEC HANDBOOK.   ANY QUESTIONS PLEASE CALL.       4) NOTE: PLEASE INDICATE LOADS FOR SHOW WINDOW   RECEPTACLES PER 220.14G FOR BRANCH CIRCUIT SIZING AND   220.43A FOR LOAD WHICH IS REQUIRED TO BE USED FOR   SIZING SERVICE.       5) NOTE: PLEASE SEE 600.5 WHICH REQUIRES THE SIGN   CIRCUIT TO BE DEDICATED. THIS CIRCUIT IS NOT PERMITTED   TO HAVE ANY OTHER ITEMS SUCH AS SOFFITS LIGHTS ETC ON   THE SAME CIRCUIT.   THE MINIMUM VA TO BE FIGURED FOR SIZING OF THIS CIRCUIT   SHALL BE 1200VA. PLEASE ADJUST PLANS AND CALCULATIONS.       6) NOTE: RISER SHOWS AN *EQUIPMENT GROUNDING CONDUCTOR*   BEFORE THE FIRST MEANS OF DISCONNECT WHICH IS NOT   PERMITTED. PLEASE SEE 250.6, 250.24. THE CODE REQUIRES   THE NEUTRAL TO BE BONDED AT THE FIRST MEANS OF   DISCONNECT. IF THERE IS AN EQUIPMENT GROUNDING   CONDUCTOR INSTALLED FROM THE METER TO THIS FIRST MEANS   OF DISCONNECT THEN THIS WOULD PARALLEL THE NEUTRAL THUS   CREATING OBJECTIONABLE CURRENTS.       7) NOTE: PLEASE COMPLETE CIRCUITS ON PLANS. ONE EXAMPLE   IS EQUIPMENT IDENTIFIED AS SOUP COUNTER. IS THIS   EQUIPMENT? OR IS THE SOUP WARMER THE ONLY APPLIANCE?   PLEASE ALSO SEE TOILET HAND DRYER WHICH INDICATES   CIRCUITS *B 19-20*. THIS PLACES CONDUCTORS ON THE SAME   PHASE WHICH WILL NOT WORK.   PER THE PANEL SCHEDULE THIS SHOULD BE 19-21.   PLEASE BE SURE TO COORDINATE ALL.   408.4, 310.16 ETC   FBC 106.1.1, 106.5       8) NOTE: PLEASE SUBMIT THE MANUFACTURES SPECS/CUT   SHEETS FOR THE PROPOSED MANUAL TRANSFER SWITCH AS   STATED ON PLANS. 701.7, 110.3, 90.7       9) NOTE: PLEASE SEE 210.8B4 AS *ALL* OUTSIDE   RECEPTACLES UNDER THE CHANGES IN THE 2005 NEC SHALL BE   GFI PROTECTED. THIS INCLUDES ANY DEDICATED CIRCUITS FOR   ITEMS SUCH AS ICE MACHINES ETC.       10) NOTE: PLEASE INDICATE THE TYPE OF TIME CLOCK TO   MEET 13-415.AB.1.4. THIS MUST BE ASTRONOMICAL WITH A   MINIMUM OF 10HR PROGRAMMING BACK UP.       11) NOTE: PLEASE SHOW ALL CLASS AND DIVISION LOCATIONS   PER NEC 500,514.3.(B)(1) PLEASE ALSO SEE (2) UNDER SAME   SECTION FOR ANY PROPOSED NG, OR LP.       12) NOTE: PLEASE SEE 514.11 (A)(B)(C) ETC.       13) NOTE: PLEASE INCLUDE ALL WIRING AND DETAILS FOR THE   REST OF NEC 514. 514.4,514.7,514.9,514.16.       14) NOTE: PLEASE SEE 225.31- 225.39 FOR DISCONNECTING   MEANS FOR SEPARATE STRUCTURES.           15) NOTE: PLEASE VERIFY SERVICE RISER. SERVICE IS SHOWN   AS 600AMPS WITH A *600* AMP METER CAN. IS THIS NOT A CT   TYPE OF INSTALLATION ? PLEASE CHECK WITH FPL AND   MANUFACTURE. SEE FPL SERVICE STANDARDS.       16) NOTE: PLEASE COORDINATE PLANS. THE PLANS SHOW AND   NOTE THE SERVICE TO BE AN OVERHEAD TYPE YET RISER SHOWS   THIS AS UNDERGROUND. WHICH ONE WILL IT BE?   REVIEW CAN NOT BE DONE ON AN OVERHEAD SERVICE AS IT IS   NOT SHOWN ON RISER.   230,310.16 ETC   FBC 106.1.2 FOR ADDITIONAL INFORMATION AND CLARITY OF   PLANS.                           * IMPORTANT **   ONCE AUDIT/REVIEWS ARE COMPLETE AND PLANS ARE PICKED UP   FOR CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE   ALL OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED   SHEETS INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING.   DO NOT LEAVE ANY OLD/VOIDED SHEETS IN SETS.   PLEASE DO NOT ATTACH SUPPORTING DOCUMENTS TO PLANS. ANY   ADDITIONAL DOCUMENTATION SUCH AS PRODUCT APPROVALS,   SPEC/CUT SHEETS, CALCULATIONS ETC. SHOULD BE PLACED   INTO TWO SETS/FOLDERS/BINDERS ETC.   PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS   SHOULD BE SUBMITTED FOR REFERENCE.   THIS WILL HELP IN THE AUDIT/REVIEW PROCESS AND AVOID   ANY DELAYS.       IF THERE ARE ANY QUESTIONS; OR IF COMMENTS ARE NOT   TYPED IN A CLEAR MANNER PLEASE DO NOT HESITATE TO   CONTACT THIS REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPARTMENT   CITY OF WEST PALM BEACH   561-805-6717   [email protected]                 Review Stop E ELECTRICAL Rev No 3 Status F Date 2007-10-18 Cont ID   Sent By dpalmer Date 2007-10-18 Time 14:50 Rev Time 0.00 Received By dpalmer Date 2007-10-18 Time 10:26 Sent To   Notes 2007-10-18 15:41:22 *** DENIED 3RD REVIEW *****       ** PLEASE SEE SOME ITEMS FROM PREVIOUS REVIEW NOTES ARE   STILL IN NEED OF ADDRESSING. THERE ARE ALSO SOME NEW   COMMENTS ON SHEETS OTHER THAN THE ELECTRICAL BASED ON   CHANGES TO PLANS.       1) NOTE: PLEASE SEE AS STATED IN THE TWO PREVIOUS   REVIEWS. THE PLANS ARE STILL ONLY SUBMITTED FOR *PLAN   REVIEW *.       ** PLEASE KNOW THIS IS STILL UNDER "PLAN REVIEW" ONLY.   NO APPLICATION FOR PERMIT HAS YET BEEN MADE TO DATE.   PLEASE KNOW THAT EVEN ONCE PLANS ARE CODE COMPLIANT,   REVIEWS WILL STILL REMAIN IN *FAILED* STATUES UNTIL   PERMIT APPLICATION IS MADE AND REVIEW OF LICENSING,   APPLIED VALUES ETC FOR COMPLETE SCOPE OF WORK CAN BE   DONE.       2) NOTE: PLEASE SEE THE ARCHITECTURAL PLANS AND   LANDSCAPE PLANS, ETC STILL NEED COORDINATION WITH ALL   OTHER SHEETS AND TRADES.   PLEASE SEE FOR EXAMPLE THE ELECTRICAL LIGHTING WHICH IS   SHOWN ON LP DOES NOT CORRELATE WITH SITE PLANS.   PLEASE SEE FOR EXAMPLE THE DETAILS OF WALKS/ACCESS ETC   ON SITE PLAN DETAILS DO NOT MATCH WITH THE SITE PLAN   ITSELF. PLEASE SEE COMMENTS FROM OTHER TRADES SUCH AS   ZONING AS ANY CHANGES ON THESE SHEETS WILL HAVE AN   AFFECT ON ELECTRICAL PLANS ALSO.   PLEASE CORRELATE ELECTRICAL PLANS WITH SITE/LANDSCAPE   PLANS AS THERE ARE LIGHTING FIXTURES FOR SITE ETC SHOWN   ON LP WHICH ARE NO WHERE ON ELECTRICAL SHEETS.   NO WIND LOAD INFORMATION, NO CIRCUITING, NO LOADS, ETC   PLEASE CORRELATE ALL AND COMPLETE.   FBC 106.1, 106.1.2, 106.3.5.1.2   NEC 240, 310.16, 408.4       3) NOTE: PLEASE SEE SEVERAL OF THE LANDSCAPE SHEETS ARE   NOT SIGNED, DATED OR SEALED AS REQUIRED PER FS 481.321   PLEASE ALSO SEE MISSING INFORMATION ON TITLE BLOCKS FOR   PRINTED NAME AND LICENSE NUMBER FOR SAID DESIGNER.       4) NOTE: PLEASE SUBMIT THE MANUFACTURES SPECS/CUT FOR   THE ATS AND GENERATOR AS REQUESTED ON THE PREVIOUS TWO   REVIEWS.   THE SUB BASE FUEL TANK SPECS ARE ALSO REQUIRED AND WILL   BE REVIEWED BY OTHER   110.3, 90.7.       5) NOTE: PLEASE SUBMIT THE FUEL CONSUMPTION ON THE   GENERATOR AS PREVIOUSLY REQUESTED FOR HB 7121, HB 319,   AND HB 965. CAN NOT LOCATE ANYWHERE ON PLANS THAT THE   ON-SITE FUEL WILL SUPPLY THE REQUIRED 72HRS OF FUEL   UNDER LOAD CONSUMPTION.       6) NOTE: ONCE AGAIN THE GENERATOR IS STILL BEING SHOWN   FOR 434AMPS, YET THIS CAN NOT BE CONFIRMED. THIS IS   125KW AT 208V 3-PHASE. IF THIS IS 434AMPS, HOW IS IT   THAT THE GENERATOR HAS A 400AMP BREAKER?   PLEASE SEE COMMENT #4 ABOVE.       7) NOTE: PLEASE SEE MISSING LIGHTING POWER   DENSITIES/CALCULATIONS AS REQUIRED PER 13-415.2.   PLEASE SEE EXTERIOR LIGHTING CALCULATIONS COULD STILL   NOT BE LOCATED ON PLAN/ENERGY CALCULATIONS ETC.   13-415.2.ABC.1.3   ** INTERIOR IS ON PLANS AND IS OK.   PLEASE SEE THAT NO ENERGY CALCULATIONS WERE SUBMITTED   FOR REVIEW.?   PLEASE SEE 13-415.1.AB.1.1   PLEASE SEE 13-103.1.1.1 AS THE DESIGNERS OF RECORD   SHALL SIGN, DATE AND SEAL SAID ENERGY CALCULATIONS AND   OTHER INFORMATION AS REQUIRED UNDER CHAPTER 13. PLEASE   BE SURE TO SEE THE 2006 REVISIONS TO THE 2004 FBC AS   CHANGES WERE MADE.       ** PLEASE KNOW AS THERE IS SOME INFORMATION STILL NOT   YET SUBMITTED FOR REVIEW, COMPLETE REVIEW CAN NOT BE   DONE.           ** PLEASE BE SURE TO CALL IF THERE ARE ANY QUESTIONS OR   COMMENTS WITH RESPECT TO THE TYPED COMMENTS ABOVE. IF   THERE ARE ANY COMMENTS WHICH ARE NOT CLEAR IN ANY WAY,   NOT UNDERSTOOD OR NOT TYPED IN A CLEAR MANOR, PLEASE DO   NOT HESITATE IN CONTACTING THIS OFFICE AND THIS   REVIEWER.       * ** IMPORTANT**   ONCE ALL REVIEWS ARE DONE AND PLANS ARE PICKED UP FOR   CORRECTIONS, PLEASE BE SURE TO COMPLETELY REMOVE ALL   OLD/VOIDED SHEETS AND ONLY INSERT NEW REVISED SHEETS   INTO TWO COMPLETE SETS FOR REVIEW AND STAMPING. DO NOT   LEAVE ANY OLD/VOIDED SHEETS IN SETS.   PLEASE KNOW ONLY ONE SET OF THE OLD/VOIDED SHEETS   SHOULD BE SUBMITTED FOR REFERENCE.   THIS WILL HELP IN THE REVIEW PROCESS AND AVOID ANY   DELAYS.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPT.   CITY OF WEST PALM BEACH   561-805-6717   [email protected] Review Stop E ELECTRICAL Rev No 2 Status F Date 2007-03-24 Cont ID   Sent By dpalmer Date 2007-03-24 Time 14:18 Rev Time 0.00 Received By dpalmer Date 2007-03-24 Time 12:06 Sent To   Notes 2007-03-24 14:20:49         ****** UNSAT 2ND REVIEW******       ** PLEASE KNOW THAT ANY REFERENCE TO THE FBC CHAPTER 1   IN THE PLAN REVIEW COMMENTS CAN BE FOUND IN THE   ADMINISTRATIVE SECTION OF THE 2004 FBC AS ADOPTED BY   THE CITY OF WEST PALM BEACH.           ** PLEASE KNOW THIS IS STILL UNDER "PLAN REVIEW" ONLY.   NO APPLICATION FOR PERMIT HAS YET BEEN MADE TO DATE.   PLEASE KNOW THAT EVEN ONCE PLANS ARE CODE COMPLIANT,   REVIEWS WILL STILL REMAIN IN *FAILED* STATUES UNTIL   PERMIT APPLICATION IS MADE AND REVIEW OF LICENSING,   APPLIED VALUES ETC FOR COMPLETE SCOPE OF WORK CAN BE   DONE.       ** PLEASE SEE MANY ITEMS FROM PREVIOUS REVIEW NOTES   WERE NOT DONE OR SUBMITTED.   A COMPLETE REVIEW FOR CODE COMPLIANCE CAN NOT BE DONE   AT THIS TIME AS THESE ITEMS ARE NOT SHOWN OR   SUBMITTED.   THERE MAY BE NEW COMMENTS ON THE FOLLOWING REVIEW NOT   YET MADE.           1) NOTE: PLEASE BE SURE THE PLANS, ELECTRICAL AND   ARCHITECTURAL CONTAIN ALL THE REQUIRED CODES RELEVANT   TO DESIGN.       PLEASE KNOW THAT DEPENDING ON PERMIT APPLICATION IS   FINALLY MADE, THIS WILL DETERMINE THE CODES IN WHICH   THE PLANS ARE DESIGNED UNDER.   PLEASE SEE THE ARCHITECTURAL PLANS INDICATE THE 2001   FBC????   PLEASE INCLUDE THE FOLLOWING AT A MINIMUM.   2004 FBC W/ 2006 REVISIONS ( FOR ALL TRADES)   2005 NFPA-70   2003 NFPA-101   2002 NFPA-72( IF APPLICABLE)   2002 NFPA-110   2003 NFPA-30A   2002 NFPA-37       2) NOTE: PLEASE SEE THE ARCHITECTURAL PLANS AND   LANDSCAPE PLANS ARE MISSING ALL OF THE ELECTRICAL ,   MECHANICAL AND GENERATOR EQUIPMENT FROM PLANS SHOWING   ALL SET BACKS AND DISTANCES FROM BUILDING, PROPERTY   LINES ETC.   PLEASE KNOW THAT BASED ON THE ELECTRICAL PLANS SHOWING   SOME OF THIS AND COORDINATION WITH THE ONLY *SITE*   LAYOUT PROVIDED ON THE LANDSCAPE PLANS, THE GENERATOR   DOES NOT APPEAR IT CAN BE LOCATED IN THE REAR OF   BUILDING.   PLEASE ALSO SEE THE MINIMUM REQUIREMENTS FOR ZONING   SETBACKS AND PERMITTED DISTANCES FROM BUILDING AND   PROPERTY LINES.   PLEASE SEE THE MINIMUM DISTANCES/CLEARANCES FOR THE   GENERATOR FROM BUILDING AND PROPERTY LINE WILL PLACE   THIS UNIT TOO CLOSE TO BUILDING AND PROPERTY. A NEW   LOCATION MAY BE REQUIRED.   PLEASE SEE THE MECHANICAL COMMENTS, BUILDING COMMENTS.       MORE INFORMATION ON ALL WILL BE REQUIRED. PLEASE SEE   COMMENTS FOR GENERATOR.   FBC 106.1.2       3) NOTE: PLEASE SEE THE SEAL BEING USED BY THE   LANDSCAPE ARCHITECT IS NOT OF SUFFICIENT SIZE. PLEASE   SEE THE FAC 61G1-16.002   61G1-16.002 DESCRIPTION OF SEAL.   (1) THE SEAL SHALL CONTAIN THE NAME OF ONLY ONE   ARCHITECT OR INTERIOR DESIGNER AND THE REGISTRATION   NUMBER; THE SEAL OF THE ARCHITECT SHALL BE CIRCULAR,   AND THE SEAL OF THE INTERIOR DESIGNER SHALL BE   HEXAGONAL. BOTH SEALS SHALL BE AN IMPRESSION-TYPE METAL   SEAL, APPROXIMATELY 2" IN DIAMETER WITH TWO CIRCULAR   LINES BETWEEN WHICH LINES SHALL APPEAR, AT THE TOP, THE   WORDS "STATE OF FLORIDA" AND AT THE BOTTOM THE WORDS   "REGISTERED ARCHITECT" OR "LICENSED INTERIOR DESIGNER,"   WHICHEVER IS APPLICABLE.   (2) ANY INDIVIDUAL WHO IS BOTH A REGISTERED ARCHITECT   AND A LICENSED INTERIOR DESIGNER MUST USE A SEAL WHICH   CONTAINS BOTH THE ARCHITECT AND INTERIOR DESIGN   REGISTRATION NUMBERS, IN SUCH A MANNER:       4) NOTE: PLEASE SEE THE MISSING INFORMATION ON TITLE   BLOCKS PER 61G1-16.004. PLEASE SEE MISSING THE PRINTED   NAME, PRINTED LICENSE NUMBER AND MISSING FIRM LICENSE   NUMBER. (ALSO KNOWN AS THE CERTIFICATE OF AUTHORIZATION   NUMBER.   PLEASE SEE FS 481.219       5) NOTE: PLEASE SEE MISSING LIGHTING POWER   DENSITIES/CALCULATIONS AS REQUIRED PER 13-415.2. A NOTE   ON PLANS WHICH MENTIONS THE DESIGN MEETS THIS SECTIONS   DOES NOT ALLEVIATE THE REQUIRED INFORMATION TO BE SHOWN   ON RECORD SETS OF PLANS AS REQUIRED PER THE SAME   SECTION OF THE FBC CHAPTER 13.   PLEASE SEE THAT NO ENERGY CALCULATIONS WERE SUBMITTED   FOR REVIEW.?   PLEASE SEE 13-415.1.AB.1.1   PLEASE SEE 13-103.1.1.1 AS THE DESIGNERS OF RECORD   SHALL SIGN, DATE AND SEAL SAID ENERGY CALCULATIONS AND   OTHER INFORMATION AS REQUIRED UNDER CHAPTER 13. PLEASE   BE SURE TO SEE THE 2006 REVISIONS TO THE 2004 FBC AS   CHANGES WERE MADE.       6) NOTE: PLEASE SHOW AND INCLUDE A LAYOUT ON PLANS   SHOWING ALL CLASS AND DIVISION LOCATIONS AS REQUIRED   PER NEC 511, 500 AND NFPA-30A.   PLEASE PROVIDE A DETAIL FOR THE SHUNT/EM STOP DEVICE   HOW THESE ARE BEING CONNECTED TO THE FEEDS.   PLEASE SEE THE PANEL SCHEDULES WHICH DO NOT INDICATE   SHUNT TRIPS REQUIRED?       7) NOTE: PLEASE SEE NFPA-96 AS THE ELECTRICAL UNDER   HOODS SHALL ALSO CONTAIN SHUNT AND DETAIL TO BE SHOWN.   PLEASE SEE COMMENTS FROM OTHER TRADES FOR MORE   INFORMATION ON GAS AND HOODS.       8) NOTE: PLEASE SEE THE CODE SECTION REFERENCED FOR THE   GFI PROTECTION OF THE KITCHEN OUTLETS SEEMS TO BE A   MISPRINT.   PLEASE SEE 210.8B3   PLEASE ALSO SHOW ALL OF THESE CIRCUITS WHICH WILL BE   PROTECTED. PLEASE INDICATE ON PANEL SCHEDULE OR PLANS.   STATING THE SECTION OF THE CODE IS ONLY PART OF WHAT IS   NEEDED.   FBC 106.1.2       9) NOTE: PLEASE SEE HB 7121, HB 319, HB965 ETC THIS IS   HOUSE BILL 7121 WHICH WAS JUST ADOPTED INTO LAW ON JULY   1ST, 2006. PLEASE SEE FS 252, 526.143ETC, WHICH NOW   REQUIRES ALL FUEL STATIONS UPON BEING NEW OR   SUBSTANTIAL REMODEL, ETC INSTALL A COMPLETE EMERGENCY   BACK UP GENERATOR SYSTEM.PLEASE PROVIDE THE MINIMUM   AMOUNT OF FUEL, FUEL CONSUMPTION FOR ALL LOADS. PLEASE   SEE THAT UNDER THE FS 526.143 STATES THE MINIMUM AMOUNT   OF TIME REQUIRED FOR OPERATIONS OF GENERATOR WHICH IS   72HRS.   PLEASE SUBMIT ALL REQUIRED LOCATIONS PER NEC 500.   PLEASE SUBMIT ALL MANUFACTURES SPECS/CUT SHEETS FOR ALL   EQUIPMENT, ATS, MTS, GEN, FUEL PRIME MOVER ETC. PLEASE   INDICATE THE AMOUNT OF ONSITE FUEL. PLEASE SEE THE NEW   FLORIDA STATUTES FOR THE REQUIRED TIMES AND AMOUNT OF   ON SITE FUEL REQUIRED. PLEASE SEE HB AS NOTED. PLEASE   SEE THE GENERATOR NOTE ON PLANS MENTIONS THE GENERATOR   IS GOOD FOR 434 AMPS. PLEASE VERIFY HOW THIS IS   POSSIBLE WITH A 125KW UNIT AT 3-PHASE, 120/208V? PLEASE   ALSO SEE NOTE WHICH MENTIONS THAT THE GENERATOR   MANUFACTURE IS TO PROVIDE CALCULATIONS WHICH WILL MEET   THE INTENDED LOADS. PLEASE KNOW THAT THIS INFORMATION   FOR THE MINIMUM DESIGN IS REQUIRED AT THIS TIME. PLEASE   KNOW THIS IS AND WILL BE REQUIRED. 90.7, 110.3 ETC   PLEASE KNOW THAT ONE THE SPECS ARE SUBMITTED THE REVIEW   OF MANY ITEMS WILL BE ABLE TO BE DONE AT THAT TIME. **   PLEASE SEE THAT AS THIS IS LEGALLY REQUIRED SYSTEM   PLEASE BE SURE TO SEE ALL OF THE REQUIREMENTS UNDER   NFPA-110, AND NEC 701.       10) NOTE: PLEASE SE NOTE ON PLANS WHICH MENTIONS THAT   THE CONTRACTOR IS REQUIRED TO THE TRANSFORMER WITH THE   FPL SERVICE PLANNER FOR THE AVAILABLE FAULT CURRENT.   PLEASE KNOW THAT THIS IS REQUIRED TO BE DONE AT THIS   TIME. IT IS THE RESPONSIBILITY OF THE DESIGNER AND   DESIGN TEAM.   110.9       11) NOTE: PLEASE KNOW THAT UNTIL THE MANUFACTURES   SPECS/CUT SHEETS ARE SUBMITTED FOR THE SERVICE ENTRANCE   ATS, REVIEW FOR THE CODE COMPLIANCE FOR 225.31-225.39,   230.76, 230.79 CAN NOT BE DONE.   701, 110.27.       12) NOTE: PLEASE SEE RISER NOTES WHICH MENTIONS THE TWO   DISCONNECTS ON THE LINE SIDE OF SUB PANELS AND ON THE   LOAD SIDE OF THE GUTTER AS MAINS 1 OF 2 AND 2OF 2? HOW   IS THIS POSSIBLE WHEN THE SERVICE MEANS OF DISCONNECTS   ARE LOCATED IN THE ATS.   OCP AT GENERATOR SHALL BE SHOWN.   PLEASE SEE 445.13 WHICH MAY APPLY FOR THE MINIMUM   SIZING OF THE CONDUCTORS.   PLEASE SHOW ALL EQUIPMENT ON PLANS AT BUILDING   INCLUDING BOTH MAINS.   110.26   FBC 106.1.2       13) NOTE: PLEASE PROVIDE COMPLETED PLANS FOR THE SLAB   DETAIL, ELEVATION OF THE UNIT AND SERVICE. EQUIPMENT IS   PART OF A LEGALLY REQUIRED SYSTEM SEE LOCATIONS AND   ELEVATIONS IN NFPA-110 CHAPTER 7   THE LOCATION, ENCLOSURE AND GENERATOR SHALL BE   PROTECTED FROM VANDALISM, FLOODS, ETC.       14) NOTE: PLEASE SEE THAT FEES ARE OWED AS THE AMOUNT   OF SHEETS SUBMITTED IS GREATER THAN THAT PLACED ON   SUBMITTIAL SHEET.       ** PLEASE KNOW AS THERE IS MUCH INFORMATION NOT YET   SUBMITTED AND MANY CHANGES WHICH WILL BE REQUIRED ON   PLANS, FURTHER COMMENTS MAY BE EXTENDED ON THE   FOLLOWING REVIEW.       * ** IMPORTANT**   ONCE ALL REVIEWS ARE DONE AND PLANS ARE   PICKED UP FOR CORRECTIONS, PLEASE BE   SURE TO COMPLETELY REMOVE ALL OLD/VOIDED   SHEETS AND ONLY INSERT NEW REVISED   SHEETS INTO TWO COMPLETE SETS FOR REVIEW   AND STAMPING. DO NOT LEAVE ANY   OLD/VOIDED SHEETS IN SETS.   PLEASE KNOW ONLY ONE SET OF THE   OLD/VOIDED SHEETS SHOULD BE SUBMITTED   FOR REFERENCE.   THIS WILL HELP IN THE REVIEW PROCESS AND   AVOID ANY DELAYS.       ** PLEASE BE SURE TO CALL IF THERE ARE ANY QUESTIONS OR   COMMENTS WITH RESPECT TO THE TYPED COMMENTS ABOVE. IF   THERE ARE ANY COMMENTS WHICH ARE NOT CLEAR IN ANY WAY,   NOT UNDERSTOOD OR NOT TYPED IN A CLEAR MANOR, PLEASE DO   NOT HESITATE IN CONTACTING THIS OFFICE AND THIS   REVIEWER.       DEWEY PALMER   ELECTRICAL PLAN REVIEW II   CONSTRUCTION SERVICES DEPT.   CITY OF WEST PALM BEACH   561-805-6717   [email protected] 2007-03-24 12:47:49 IN ELEC FOR REVIEW Review Stop E ELECTRICAL Rev No 1 Status F Date 2006-11-04 Cont ID   Sent By dpalmer Date 2006-11-04 Time 19:45 Rev Time 0.00 Received By dpalmer Date 2006-11-04 Time 18:46 Sent To   Notes 2006-11-04 19:45:09 *** UNSAT ***           ** PLEASE KNOW THIS IS STILL UNDER "PLAN REVIEW" ONLY.   NO APPLICATION FOR PERMIT HAS YET BEEN MADE TO DATE.   PLEASE KNOW A CODE CHANGE FOR NFPA-70 IS COMING AND IF   PERMIT IS NOT APPLIED FOR BEFORE STATE ADOPTS NEW CODE,   THEN THE PLANS WILL BE REQUIRED TO CHANGE AS NEEDED.   THE TENTATIVE DATE IS DEC 1ST, 2006       1) NOTE:PLEASE SEE PLANS SEEM TO INDICATE A NEW STORE   BEING CONSTRUCTED, HOWEVER THE "PLAN REVIEW" SUBMITTAL   SHEET INDICATES A REMODEL??? THE SCOPE OF WORK IS   UNCLEAR BASED ON PLANS SUBMITTED IN EITHER CASE.       2) NOTE: PLEASE SEE FS 471.003(2)(H)2A, AS PLANS ARE   REQUIRED TO BE DONE BY A FLORIDA REGISTERED   PROFESSIONAL ENGINEER.   PLEASE ALSO SEE FS 471.025(3).   THE ELECTRICAL SCOPE AS SHOWN MAY NOT BE DONE BY AN   ARCHITECTURAL FIRM/ARCHITECT.       3) NOTE: PLEASE KNOW THE PLANS SUBMITTED ARE NOT   COMPLETE FOR CODE COMPLIANCE. PLEASE SEE ONLY SOME CODE   ARTICLES BELOW ARE BEING GIVEN. PLEASEKNOW THERE IS A   SUBSTANTIALLY AMOUNT OF CODE RELATED ITEMS NOT   SUBMITTED OR SHOWN.       A) PLEASE INDICATE AND SHOW ALL CIRCUITING ON PLANS AND   CORRELATE WITH PANEL SCHEDULES TO BE SUBMITTED.   240.4,310.16, 408.4   FBC ADMINISTRATIVE SECTION AS ADOPTED BY THE CITY OF   WEST PALM BEACH. 106.1.2, 106.3.5.1.2 ETC.   PLEASE ALSO SEE 2002 NFPA-70, 2003 NFPA-101, 2002   NFPA-72, NFPA-30A ETC ETC.   B) PLEASE SUBMIT LOAD CALCULATIONS.NEC 220.   C) PLEASE SEE NEC 511   D) PLEASE SEE LS 101 7.8, 7.9 FOR MISSING EM/ EXT LTS,   PLEASE ALSO SEE 700.12E FOR CIRCUITING.   E) PLEASE SEE 250.6, 250.24B   F) PLEASE SEE 250.110, 250.110   G) PLEASE SEE 250.50   H) PLEASE SEE 600.5, 220.3(B)(6)   I) PLEASE SEE 210.62, 220.12A   J) PLEASE SEE 210.8B3   K) PLEASE SEE FBC CHAPTER 13(ALL APPLICABLE SECTIONS,   TOO MANY TO LIST AT THIS TIME.   L) PLEASE SEE 110.9, 240.12 FOR SELECTIVE COORDINATION   DETAILS TO BE SUBMITTED.   ETC.       4) NOTE: PLEASE SEE HB 7121, HB 319, HB965 ETC THIS IS   HOUSE BILL 7121 WHICH WAS JUST ADOPTED INTO LAW ON JULY   1ST, 2006. PLEASE SEE FS 252 ETC, WHICH NOW REQUIRES   ALL FUEL STATIONS UPON BEING NEW OR SUBSTANTIAL   REMODEL, ETC INSTALL A COMPLETE EMERGENCY BACK UP   GENERATOR SYSTEM. THIS WILL SUBSTANTIALLY CHANGE THE   PLANS SUBMITTED.   PLEASE SUBMIT SITE PLANS, ALL REQUIRED LOCATIONS PER   NEC 500. PLEASE SUBMIT ALL MANUFACTURES SPECS/CUT   SHEETS FOR ALL EQUIPMENT, ATS, MTS, GEN, FUEL PRIME   MOVER ETC ETC.   PLEASE KNOW THIS IS AND WILL BE REQUIRED. 90.7, 110.3   ETC           ** PLEASE KNOW AS PLANS ARE NOT COMPLETE AT THIS TIME   FOR A SUFFICIENT REVIEW, AND WILL BE CHANGING, THERE   MAY BE FURTHER COMMENTS UPON THE NEXT REVIEW.           * ** IMPORTANT**   ONCE ALL REVIEWS ARE DONE AND PLANS ARE   PICKED UP FOR CORRECTIONS, PLEASE BE   SURE TO COMPLETELY REMOVE ALL OLD/VOIDED   SHEETS AND ONLY INSERT NEW REVISED   SHEETS INTO TWO COMPLETE SETS FOR REVIEW   AND STAMPING. DO NOT LEAVE ANY   OLD/VOIDED SHEETS IN SETS.   PLEASE KNOW ONLY ONE SET OF THE   OLD/VOIDED SHEETS SHOULD BE SUBMITTED   FOR REFERENCE.   THIS WILL HELP IN THE REVIEW PROCESS AND   AVOID ANY DELAYS.       PLEASE SUBMIT THE ABOVE INFORMATION FOR   REVIEW. IF THERE ARE ANY QUESTIONS,   PLEASE DO NOT HESITATE TO CALL.       DEWEY PALMER   ELECTRICAL PLAN REVIEW   CONSTRUCTION SERVICES DEPT.   CITY OF WEST PALM BEACH   561-805-6717   [email protected] Review Stop ENG ENGINEERING CSD Rev No 7 Status P Date 2009-11-30 Cont ID   Sent By   Date 2009-11-30 Time   Rev Time 5.00 Received By   Date 2009-11-30 Time   Sent To ENG Notes 2009-11-30 14:48:14 PLANS ARE APPROVED AS-NOTED THRU ESD DATED 11/30/09   1) FOR EACH INLET , PROVIDE A 12" DIA WEEP HOLE AS   SHOWN ON THE DETAIL ON SHT 3 OF 3. UNDER THE WEEP HOLE   INSTALL HARDWARE CLOTH (SS) ON   2' X 2' X 6" OF WASHED ROCK WRAPPED ALL AROUND WITH   FABRIC.   2) FOR EACH INLET , PROVIDE A POLLUTION CONTROL BAFFLE   (PCB) AT EACH PIPE OUTLET TO EXFILTRATION TRENCH (6   TOTAL ).       MANUEL JULIAN GONZALEZ   ENGINEERING PROJECT COORDINATOR   ENGINEERING SERVICES DEPARTMENT   401 CLEMATIS STREET, 4TH FLOOR   WEST PALM BEACH, FL 33401   (MAILING ADDRESS: P.O. BOX 3366, ZIP 33402)   MAIN PHONE: (561) 822-1200   DIRECT: (561) 494-1085   FAX: (561) 494-1116   MOBILE: (561) 644-7301   EMAIL: [email protected]   WWW.WPB.ORG/ENGINEERING     Review Stop ENG ENGINEERING CSD Rev No 6 Status F Date 2009-09-23 Cont ID   Sent By mgonzale Date 2009-09-23 Time 10:54 Rev Time 1.00 Received By mgonzale Date 2009-09-23 Time 10:49 Sent To   Notes 2009-09-23 10:54:14 FAILED       PLANS MUST BE SUBMITTED TO ENGINEERING DEPT FOR   STORMWATER REVIEW.   THIS IS A SEPARATE SUBMITTAL REQUIRED BY ENGINEERING   DEPT TO COMPLY WITH NPDES CODES.       INFORMATION ON SUBMITTAL CAN BE OBTAINED AT THE LINK   BELOW:   HTTP://WWW.CITYOFWPB.COM/ENGINEERING/ENG_FORMS.PHP       DEVELOPMENT PERMIT PACKET MUST ACCOMPANY YOUR SUBMITTAL   ALONG WITH THE REQUIRED DOCUMENTATION.   SEE "ENGINEERING SERVICES DEPARTMENT STANDARD   APPLICATION FOR DEVELOPMENT PERMIT"       SUBMIT THE PERTINENT DOCUMENTS ATTENTION:   BRIAN MOREE, CONSTRUCTION SUPERVISOR   ENGINEERING SERVICES DEPARTMENT   401 CLEMATIS STREET, 4TH FLOOR   WEST PALM BEACH, FL 33401   (MAILING ADDRESS: P.O. BOX 3366, ZIP 33402)   MAIN PHONE: (561) 822-1200   DIRECT: (561) 494-1098   FAX: (561) 494-1116   EMAIL: [email protected]   WWW.WPB.ORG/ENGINEERING         Review Stop ENG ENGINEERING CSD Rev No 5 Status F Date 2009-07-27 Cont ID   Sent By dlauderm Date 2009-07-27 Time 13:53 Rev Time 2.00 Received By dlauderm Date 2009-07-27 Time 12:37 Sent To   Notes 2009-07-27 13:19:57 FAILED   DEAN LAUDERMILK, PROJECT COORDINATOR   CSD: (561) 805-6716   ESD: (561) 494-1083   EMAIL: [email protected]   TOO MANY CONTRADICTIONS TO APPROVE THE PLANS AS   SUBMITTED.   1. GREASE TRAP ON CIVIL PLAN (2 OF 3) DOES NOT MATCH   PLUMBING PLAN (P-1 & P-2). NEITHER DESIGN MATCHES OUR   STANDARD DETAIL, WHICH WAS NOT INCLUDED IN THE CIVIL OR   PLUMBING PLANS.   2. WATER SERVICE, METER AND BACKFLOW PREVENTER ARE TO   REMAIN, PER CIVIL PLAN (2 OF 3), WHILE PLUMBING PLAN   (P-2) SHOWS A NEW 1" SERVICE TO THE CITY MAIN.   3. WATER SERVICE FROM BUILDING TO THE METER AND   BACKFLOW PREVENTER ARE TO REMAIN, PER CIVIL PLAN (2 OF   3), WHILE PLUMBING PLAN (P-2) SHOWS A NEW 1" SERVICE   FROM THE BUILDING TO THE METER/BACKFLOW PREVENTER.   4. IRRIGATION PLAN (IR-1) SHOWS METER AND BACKFLOW   PREVENTER AT NW CORNER OF SITE, THERE IS NO WATER MAIN   IN THE ALLEY, THE WATER METER NEEDS TO BE ON LAKE   AVENUE. IS THE INTENTION TO INSTALL A SEPARATE 1"   SERVICE FOR THE IRRIGATION SYSTEM? THE PLUMBING PLAN   SHOWS NO TEE IN THE LINES AND NO BACKFLOW PREVENTER FOR   THE IRRIGATION SYSTEM. ALL BACKFLOW PREVENTERS NEED TO   BE INSTALLED BY A LICENSED PLUMBER, NOT AN IRRIGATION   COMPANY.   5. IRRIGATION PLAN (IR-1) SHOWS 5 ZONES, TWO OF THE   ZONES ARE DESIGNED FOR MORE WATER THAN THE 1" WATER   METER IS DESIGNED TO GIVE. THE MAXIMUM SAFE OPERATING   RATE FOR A 1" METER IS 25 GPM. REDESIGN THE IRRIGATION   SYSTEM ZONES SO THE MAXIMUM GPM RATE DOES NOT EXCEED 25   GPM   6. THE IRRIGATION SYSTEM WILL NEED A SEPARATE BACKFLOW   PREVENTER WHICH IS CALLED OUT ON THE IRRIGATION PLAN   BUT IS NOT SHOWN ON THE PLUMBING PLAN OR CIVIL PLAN.   THE CIVIL PLAN (2 OF 3) SHOWS GATES ON THE EQUIPMENT   ENCLOSURE OPENING TO THE EAST. THE APPROVED SITE PLAN   AND THE BUILDING PLANS SHOWS THE GATE OPENING TO THE   SOUTH (THE CORRECT WAY).   7. THIS PLAN HAS NOT BE REVIEWED/APPROVED BY THE   ENGINEERING DEPARTMENT. WHEN THE CORRECTIONS ARE MADE   SUBMIT THE CIVIL PLAN AND THE STORMWATER CALCULATIONS   TO THE ENGINEERING SERVICES, ATTENTION EMERY FABIAN,   THE PROJECT COORDINATOR FOR THE PROJECT. THIS NEEDS TO   BE DONE PRIOR TO TURNING IN THE PLANS FOR ANOTHER   CONSTRUCTION SERVICES REVIEW. THE ESD STAMP (APPROVED)   NEEDS TO BE ON THE PLAN.     Review Stop ENG ENGINEERING CSD Rev No 4 Status F Date 2009-06-10 Cont ID   Sent By mgonzale Date 2009-06-10 Time 11:10 Rev Time 1.00 Received By mgonzale Date 2009-06-10 Time 11:00 Sent To   Notes 2009-06-10 11:10:35 ********* NOT APPROVED ***********       SUPPLY THE FOLLWING TO CITY OF WEST PALM BEACH   ENGINEERING DEPT FOR APPROVAL:   SURFACE WATER QUALITY CALCULATIONS   IMPERVIOUS AND PERVIOUS CALCULATIONS   POLLUTION PREVENTION PLAN OR SUMMARY.       A 1" DOMESTIC WATER METER IS SERVING YOU PROPERTY.   SUGGESTION OF OBTAINING AN IRRGATION METER MAY BE   SUITABLE AS   THAT CONSUMPTION WILL NOT BE CHARGED SEWAGE AGAINST IT.       ANY QUESTIONS, PLEASE CONTACT:       ATTENTION: MANUEL GONZALEZ   (561) 494-1085   [email protected]                         Review Stop ENG ENGINEERING CSD Rev No 3 Status F Date 2007-10-22 Cont ID   Sent By rchokshi Date 2007-10-22 Time 15:33 Rev Time 0.00 Received By rchokshi Date 2007-10-22 Time 15:26 Sent To   Notes 2007-10-22 15:33:30 **** FAILED *****           1. PLEASE SHOW ON DRAWINGS POLLUTION PREVENTION   DETAILS,CLOTHES USED FOR SILT ETC., AND PLANS SHOWING   SILT FENCE AROUND THE SITE.       2. STORM WATER QUALITY CALCULATIONS MUST BE APPROVED   FROM 45TH STREET, ENGINEERING BEFORE WE ISSUE A   PERMIT.       PLEASE RESPOND EACH ITEM IN DETAIL TO EXPEDITE YOUR   PERMITTING PROCESS       RASIK CHOKSHI805-6723 Review Stop ENG ENGINEERING CSD Rev No 2 Status F Date 2007-03-30 Cont ID   Sent By rchokshi Date 2007-03-30 Time 14:26 Rev Time 0.00 Received By rchokshi Date 2007-03-30 Time 14:06 Sent To   Notes 2007-03-30 14:26:29 YOUR PLANS WERE REVIEWED IN REV 1 ON 11/17/06.YOU   PROVIDED SEAL & SIGNED PLANS, NOW, FOR REV 2. YOU DID   NOT PROVIDE EXPLANATIONS OF ITEMS WE LISTED IN REV 1,   DATED 11/17/06   PLEASE PROVIDE EXPLANATIONS & INFO ON THE DRAWINGS FOR   EACH OF THE ITEMS WE ASKED FOR IN REV 1 DATED   11/17/06.   ALSO, PLEASE PROVIDE DETAIL CALCULATIONS FOR WATER   QUALITY FOR BOTH CRITERIA EITHER 1" OR 2.5" CRITERIA   FOR WATER QUALITY?? WE LIKE TO SEE BOTH CRITERIA   CALCULATIONS, AND TAKE THE WORST CRITERIAFOR THE   LENGTH OF DESIGNINGEXFILTRATIONS TRENCH. IN OTHER   WORDS, DETAILEDCAL FORLENGTH OF EXFILTRATION TRENCH   ETC.       PLEASE RESPOND EACH Review Stop ENG ENGINEERING CSD Rev No 1 Status F Date 2006-11-17 Cont ID   Sent By rchokshi Date 2006-11-17 Time 15:52 Rev Time 0.00 Received By rchokshi Date 2006-11-17 Time 15:43 Sent To   Notes 2006-11-17 15:51:48 I REVIEW ONLY THE FOLLOWING.SOPLEASE PROVIDE   FOLLOWING INFO FOR COMPLETE REVIEW:   1.NEEDS SEAL & SIGN FOR ALL CIVIL DWGSBYP.E.AS   YOU PROVIDED   2. PLEASE SHOW STANDARDS NOTES OF CITY OF WPB ON   DRAWINGSFOR SIDEWALK WIDTH , ITS SLOPE, DRIVEWAY,   PARKING, HANDICAP PARKING, PAINTPER CITY CODES ETC.,,   MUST MEET PER ADA,,ETC.,   3. PLEASE SHOW ON DRAWINGSDUMPSTER & ITS ENCLOSURE   DETAILS PER CITY OF WPB, &LOCATION ON DWG, LOCATION   MUST BE ACCESSIBLE FOR PICKUP TRUCK.   4. FIRST FLOOR ELEVATION, CENTER LINE OF ROAD ,   SIDEWALK ELEVATION MUST MEET FL BLDG CODE, PLEASE SHOW   ON THE DRAWINGS.   5. PLEASE PROVIDE A COPY OF SFWMD PERMIT,& GEOTECHNICAL   REPORT   6.PLEASE SHOW STORM WATER CALCULATIONS, WHAT CRITERIA   YOU ASSUMEDFOR RUNOFF CAL.,, LIKE 1" OVER ENTIRE SITE   OR2.5"CRITERIA, ?PERVIOUS AREA, LIKE GREEN,   LAKES, ETC,IMPERVIOUS AREA CAL.,   7. WHAT IS THE SITE AREA, YOU ARE DEVELOPING FOR THIS   PROJECT ONLY ? SO, WE CAN CHECK PERVIOUS, IMPERVIOUS   CAL.   8. HOW YOU CONNECT TO THE STORM WATER PIPES IN YOUR   SITE? ITS DETAILS.PLEASE SHOW ALL STORM WATER PIPES   AROUND YOUR SITE SO, WE CANSEE THE BEST PIPE TO   CONNECT WITH THE STORM WATERFROM ALL OTHER STORM   WATER PIPES. PLEASE SHOW DETAIL OF THE CONTROL   STRUCTURES WITH ELEVATIONS, NOTCHES, BLEEDING   ELEVATION, ETC DID YOU USE EXFILTRATION TRENCH ?   9. POLLUTION PREVENTION DETAILS,CLOTHES USED FOR SILT   ETC., PLANS SHOWING SILT FENCE AROUND THE SITE   10. WATER & SEWER PLANS MUST BE APPROVED FROM 45TH   STREET (MANNY G.), UTILITY DEPT BEFORE WE APPROVED   11. ALSO PLEASE SHOW ALL CATCH BASINS NEAREST,AROUND   YOUR SITE FOR STORM WATER DRAIN.       PLEASE RESPOND EACH ITEM IN DETAIL TO EXPEDITE YOUR   PERMITTING PROCESS       RASIK CHOKSHI805-6723 Review Stop FIRE FIRE DEPARTMENT Rev No 6 Status P Date 2009-10-14 Cont ID   Sent By mawillia Date 2009-10-14 Time 15:30 Rev Time 0.00 Received By mawillia Date 2009-10-14 Time 15:11 Sent To   Notes 2009-10-14 15:15:01 *****APPROVED*****           PLAN SHEET A-5, PREVIOUSLY (8/06/09) STAMPED,   INITIALED, AND DATED ALONG WITH A-2, A-3, A-5, AND   LS-1) WAS RE-STAMPED.           CAPT. MICHAEL A. WILLIAMS   FIRE PLAN REVIEW   561-805-6722 Review Stop FIRE FIRE DEPARTMENT Rev No 5 Status P Date 2009-08-06 Cont ID   Sent By mawillia Date 2009-08-06 Time 13:50 Rev Time 0.00 Received By mawillia Date 2009-08-06 Time 13:24 Sent To   Notes 2009-08-06 13:29:14 *****APPROVED*****           PLAN SHEETS A-2, A-3, A-5, AND LS-1 WERE STAMPED,   INITIALED, AND DATED.           CAPT. MICHAEL A. WILLIAMS   FIRE PLAN REVIEW   561-805-6722 Review Stop FIRE FIRE DEPARTMENT Rev No 4 Status F Date 2009-05-29 Cont ID   Sent By mawillia Date 2009-05-29 Time 15:20 Rev Time 0.00 Received By mawillia Date 2009-05-29 Time 15:06 Sent To   Notes 2009-05-29 15:17:56 *****PROVISO*****           THE COMMENTS FROM THE PREVIOUS FIRE PLAN REVIEWS HAVE   BEEN ADDRESSED, HOWEVER THE APPROPIATE PLAN SHEETS   (A-2, A-3, A-5, LS-1, AND LS-2) TO BE FIRE-STAMPED   PROVIDED THE FOLLOWING:           1.) ON SHEET LS-1 IN THE PROJECT CODES, AMEND NFPA 101   TO 2006 (NOT 2005) EDITION.       2.) PERMIT CAN NOT BE ISSUED UNTIL A CONTRACTOR HAS   BEEN DECLARED.       3.) THE COMMENTS FROM THE OTHER TRADES HAVE BEEN   SATISFIED.           CAPT. MICHAEL A. WILLIAMS   FIRE PLAN REVIEW   561-805-6722 Review Stop FIRE FIRE DEPARTMENT Rev No 3 Status F Date 2007-10-25 Cont ID   Sent By mawillia Date 2007-10-25 Time 13:17 Rev Time 0.00 Received By mawillia Date 2007-10-25 Time 12:45 Sent To   Notes 2007-10-25 13:16:28 ****DENIED*****   THE FOLLOWING COMMENTS TAKEN FROM THE PREVIOUS FIRE   PLAN REVIEW STILL NEED TO BE ADDRESSED:           3.CONSTRUCTION AND/OR DEMOLITION OPERATIONS SHALL NOT   HINDER OR INTERFERE WITH EMERGENCY ACCESS TO THE   PROPERTY OR VICINITY THEREOF.       4.THE NUMERICAL ADDRESS OF THE JOB SITE SHALL BE IN   THE TITLE BLOCK OF THE SUBMITTED PLAN SHEETS.NO   ADDRESS ON SHEET SP-1, LS-1, LS-2, LP-1, C2 & C3, AND   E-1       8.SPECIFY ANY NEW WALL AND CEILING INTERIOR FINISH   CLASSIFICATION IN TERMS OFCLASS "A"CLASS "B", OR   CLASS "C".       9.PROVIDE A LIFE SAFETY PLAN SHEET TO INCLUDE ALL   COMMON PATHS OF TRAVEL TO THE EXIT(S) AND THE LOCATION   OF FIRE EXTINGUISHERS AT DISTANCES WHICH SATISFY THE   75' TRAVEL DISTANCE REQUIREMENT.       NEW COMMENT       A.THE INSTALLATION OF THE STANDBY GENERATOR WILL   REQUIRE SEPARATE PLANS AND PERMIT, AND SHALL COMPLY   WITH NFPA 110.           TO EXPEDITE THE PLAN REVIEW PROCESS, INCLUDE A RESPONSE   SHEET INDICATING HOW/WHERE EACH ITEM WAS ADDRESSED.           CAPT. MICHAEL A. WILLIAMS   FIRE PLAN REVIEW   561-805-6722 Review Stop FIRE FIRE DEPARTMENT Rev No 2 Status F Date 2007-04-12 Cont ID   Sent By mawillia Date 2007-04-12 Time 17:16 Rev Time 0.00 Received By mawillia Date 2007-04-12 Time 16:37 Sent To   Notes 2007-04-12 17:16:37 ****DENIED*****   THE FOLLOWING COMMENTS TAKEN FROM THE PREVIOUS FIRE   PLAN REVIEW STILL NEED TO BE ADDRESSED:           1.NFPA 101, LIFE SAFETY CODE, 2003 EDITION SHALL BE   REFERENCED.       2.STRUCTURES UNDERGOING CONSTRUCTION, ALTERATION, OR   DEMOLITION OPERATIONS SHALL COMPLY WITH NFPA 241.       3.CONSTRUCTION AND/OR DEMOLITION OPERATIONS SHALL NOT   HINDER OR INTERFERE WITH EMERGENCY ACCESS TO THE   PROPERTY OR VICINITY THEREOF.       4.THE NUMERICAL ADDRESS OF THE JOB SITE SHALL BE IN   THE TITLE BLOCK OF THE SUBMITTED PLAN SHEETS.       5.IN ADDITION TO SHOWING WHERE THE NUMERICAL ADDRESS   WILL BE LOCATED AS ON SHEET A-2, SHOW WHAT THOSE   NUMBERS WILL BE.       8.SPECIFY THE WALL AND CEILING INTERIOR FINISH   CLASSIFICATION ASCLASS "A"CLASS "B", OR CLASS "C".       9.PROVIDE A LIFE SAFETY PLAN SHEET TO INCLUDE ALL   COMMON PATHS OF TRAVEL TO THE EXIT(S) AND THE LOCATION   OF FIRE EXTINGUISHERS AT DISTANCES WHICH SATISFY THE   75' TRAVEL DISTANCE REQUIREMENT.       NEW COMMENT       A.THE INSTALLATION OF THE STANDBY GENERATOR WILL   REQUIRE SEPARATE PLANS AND PERMIT, AND SHALL COMPLY   WITH NFPA 110.           TO EXPEDITE THE PLAN REVIEW PROCESS, INCLUDE A RESPONSE   SHEET INDICATING HOW/WHERE EACH ITEM WAS ADDRESSED.           CAPT. MICHAEL A. WILLIAMS   FIRE PLAN REVIEW   561-805-6722 Review Stop FIRE FIRE DEPARTMENT Rev No 1 Status F Date 2006-12-14 Cont ID   Sent By mawillia Date 2006-12-14 Time 11:36 Rev Time 0.00 Received By mawillia Date 2006-12-14 Time 11:36 Sent To   Notes 2006-12-14 12:11:15 *****DENIED*****               1.NFPA 101 (2003 EDITION) THE FLORIDA FIRE PREVENTION   CODE (2004 EDITION) SHALL BE REFERENCED.       2.STRUCTURES UNDERGOING CONSTRUCTION, ALTERATION, OR   DEMOLITION OPERATIONS SHALL COMPLY WITH NFPA 241.       3.CONSTRUCTION AND/OR DEMOLITION OPERATIONS SHALL NOT   HINDER OR INTERFERE WITH EMERGENCY ACCESS TO THE   PROPERTY OR VICINITY THEREOF.       4.THE NUMERICAL ADDRESS OF THE JOB SITE SHALL BE IN   THE TITLE BLOCK OF THE SUBMITTED PLAN SHEETS.       5.IN ADDITION TO SHOWING WHERE THE NUMERICAL ADDRESS   WILL BE LOCATED AS ON SHEET A-2, SHOW WHAT THOSE   NUMBERS WILL BE.       6.EXIT AND EMERGENCY LIGHTS TO BE INSTALLED AND   ARRANGED AS PER NFPA 101, 7.9 AND 7.10       7.PROVIDE THE THE FOLLOWING BUILDING INFORMATION: A)   CONSTRUCTION TYPEB) OCCUPANCY TYPEC) FIRE   PROTECTION SYSTEM I.E. FIRE ALARM AND/ORFIRE   SPRINKLERD) INTERIOR FINISH CLASSIFICATION       8.IF THE BUILDING IS UNSPRINKLERED, INTERIOR FINISH   SHALL BE CLASS "A" OR CLASS "B".       9.PROVIDE A LIFE SAFETY PLAN SHEET TO INCLUDE ALL   COMMON PATHS OF TRAVEL TO THE EXIT(S) AND THE LOCATION   OF FIRE EXTINGUISHERS AT DISTANCES WHICH SATISFY THE   75' TRAVEL DISTANCE REQUIREMENT.           TO EXPEDITE THE PLAN REVIEW PROCESS, INCLUDE A RESPONSE   SHEET INDICATING HOW/WHERE EACH ITEM WAS ADDRESSED.           CAPT. MICHAEL A. WILLIAMS   FIRE PLAN REVIEW   561-805-6722 Review Stop G GAS REVIEW Rev No 5 Status P Date 2009-12-16 Cont ID   Sent By kstevens Date 2009-12-16 Time 15:14 Rev Time 0.00 Received By kstevens Date 2009-12-16 Time 15:14 Sent To   Notes 2009-12-16 15:15:08 PLANS STILL CODE COMPLIANT. -- NO CONTRACTOR SIGNED ON   AT THIS TIME. Review Stop G GAS REVIEW Rev No 4 Status F Date 2009-08-05 Cont ID   Sent By kstevens Date 2009-08-05 Time 15:49 Rev Time 0.00 Received By kstevens Date 2009-08-05 Time 15:50 Sent To   Notes 2009-08-10 15:50:07 PLANS ARE CODE COMPLIANT BUT WILL REMAIN IN FAILED   STATUS PENDING APPLICATION FOR PERMIT BY LICENSED   CONTRACTOR. Review Stop G GAS REVIEW Rev No 3 Status F Date 2009-05-29 Cont ID   Sent By kstevens Date 2009-05-29 Time 13:52 Rev Time 0.00 Received By kstevens Date 2009-05-29 Time 13:52 Sent To   Notes 2009-05-29 13:53:58 DENIED   REFERENCE:   FBC-2007 W/2009 SUPPLEMENTS   FBC-2007 FUEL GAS       1. THE FOLLOWING INFORMATION IS REQUIRED FOR THE   SEPARAGE GAS PERMIT:       A. SUBMIT AN ISOMETRIC DRAWING THAT   CLEARLY SHOWS ALL CUT SECTIONS OF PIPE   AND CORRESPONDING LENGTHS PER FBC-2007   FUEL GAS CODE. -- THE SECTION FROM THE WALL TO THE   METER IS NOT INDICATED.       B. TYPE OF GAS, (LP OR NATURAL). -- NOT INDICATED ON   PLANS. SITE PLANS SHOWS A 1000 GAL PROPANE TANK BUT   NOTE ON SHT P-2 INDICATES TABLE 402.4(2) WHICH IS A   NATURAL GAS TABLE. PLEASE CLARIFY.       C. SHOW THE DISTANCE FROM THE POINT OF   DELIVERY, (METER), TO THE MOST REMOTE   OUTLET IN THE BUILDING AND/OR SYSTEM PER   FBC-2007 FUEL GAS CODE APPENDIX A - USE   OF CAPACITY TABLES A.3.1(4). -- TO BE VERIFIED WHEN   COMMENT 8(A) IS ADDRESSED.       D. SUBMIT MANUFACTURE SHEETS FOR ALL GAS   EQUIPMENT TO VERIFY COMPLIANCE WITH   STANDARDS NFPA 54, NFPA 58, AND THE   FBC-2007 FUEL GAS CODE SEC 402.2.       WHEN RESUBMITTING PLANS PLEASE INDICATE   THE REVISION & REMOVE & REPLACE ANY   PAGES AS NECESSARY. A TRANSMITTAL LETTER   LISTING THE ORIGINAL REVIEW COMMENT NUMBER,   WITH A DESCRIPTION OF THE REVISION MADE,   IDENTIFYING THE SHEET OR SPECIFICATION   PAGE WHERE THE CHANGES CAN BE FOUND   WILL HELP TO EXPEDITE YOUR PERMIT. REMOVE   ALL VOID SHEETS FROM ALL PLANS AND PLACE   ONE SET OF THEM LOOSELY ON TOP OF THE   COLLATED PLANS TO BE REVIEWED.   THANK YOU FOR YOUR ANTICIPATED COOPERATION.       REVIEW BY KEN STEVENS   (561) 805-6721   FAX (561) 805-6731   E-MAIL [email protected]     Review Stop G GAS REVIEW Rev No 2 Status F Date 2007-12-03 Cont ID   Sent By kstevens Date 2007-12-03 Time 07:57 Rev Time 0.00 Received By kstevens Date 2007-12-03 Time 07:56 Sent To   Notes 2007-12-03 07:59:05 DENIED   REFERENCE: FBC-2004 FUEL GAS       1. SHT A-1 INDICATES GAS EQUIPMENT IN THE KITCHEN. A   SEPARATE GAS PERMIT IS REQUIRED. SUBMIT THE FOLLOWING   INFORMATION:       A. SUBMIT AN ISOMETRIC DRAWING THAT   CLEARLY SHOWS ALL CUT SECTIONS OF PIPE   AND CORRESPONDING LENGTHS PER FBC-2004   FUEL GAS CODE.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE CORRESPONDING LENGHTS OF   EACH CUT SECTION HAVE NOT BEEN SUBMITTED, PLEASE   CLARIFY THE MARKINGS ON THE RISER DIAGRAM.       B. SHOW TYPE OF PIPING MATERIAL BEING   INSTALLED, ALL PIPE SIZES, (AND THE EDH   NUMBER OF CORRUGATED STAINLESS STEEL   TUBING FOR EACH PIPE SIZE IF BEING USED.   ****NO RESPONSE, NOT ADDRESSED.   ******NO RESPONSE, NOT INDICATED ON RISER DIAGRAM OR   ADJOINING NOTES.       C. OK - LP   D. OK       E. SHOW THE DISTANCE FROM THE POINT OF   DELIVERY, (METER), TO THE MOST REMOTE   OUTLET IN THE BUILDING AND/OR SYSTEM PER   FBC-2004 FUEL GAS CODE APPENDIX A - USE   OF CAPACITY TABLES A.3.1(4).   ****NO RESPONSE, NOT ADDRESSED.   ******NO RESPONSE, NOT ADDRESSED.       F. OK       G. INDICATE THE DELIVERY PRESSURE (PSI)   PER FBC-2004 FUEL GAS CODE SEC. 402.2.   NATURAL GAS SPECIFY .5 PSI OR 2 PSI. IF 2 PSI SHOW THE   LOCATION OF THE REGULATORS, SUBMIT MANUF.   SPECIFICATIONS FOR THE REGULATORS AND IF THE REGULATORS   ARE VENTED, INDICATE THE MATERIAL OF THE VENT AND SHOW   THE PIPING LOCATION.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE MANUF. SPECIFICATIONS DO   NOT SET THE DELIVERY PRESSURE. PLEASE ADDRESS COMMENT.       H. OK       I. SUBMIT MANUFACTURE SHEETS FOR ALL GAS   EQUIPMENT TO VERIFY COMPLIANCE WITH   STANDARDS NFPA 54, NFPA 58, AND THE   FBC-2004 FUEL GAS CODE SEC 402.2.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT MANUF. SHEETS NOT SUBMITTED.       J. OK       K. CLEARLY INDICATE ON THE PLAN IF THE   LP TANK IS ABOVE OR BELOW GROUND, AND   SHOW REQUIRED PROTECTION OF THE TANK AND APPURTENANCES   PER NFPA 58. IF THE TANK   IS BELOW GROUND THE CONTAINER SHALL BE   SECURILY ANCHORED PER NFPA 58 SECTION   3-2.2.7(H).   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE ISOMETRIC ON SHT P-1   INDICATES AN ABOVE GROUND TANK, AND THE SITE PLAN AS   WELL AS THE CIVIL SHEETS INDICATE AN UNDERGROUND TANK.   PLEASE CORRELATE.       L. EMERGENCY HOOD SHUT DOWN SHUT OFF   VALVE TO BE BELOW CEILING. MANUAL SHUT   OFF VALVE TO BE UPSTREAM. UNION TO BE   DOWN STREAM OF MANUAL VALVE.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE UNION IS NOT SHOWN, AND   MANUF. SPECIFICATION SHEETS ARE REQUIRED FOR THE ANSUL   VALVE SHOWING THAT THE VALVE IS LISTED FOR OUTSIDE   USE. Review Stop G GAS REVIEW Rev No 1 Status F Date 2007-04-09 Cont ID   Sent By kstevens Date 2007-04-09 Time 18:06 Rev Time 0.00 Received By kstevens Date 2007-04-09 Time 18:06 Sent To   Notes 2007-04-09 18:12:02 DENIED   REFERENCE: FBC-2004 FUEL GAS       THIS WAS FROM THE PREVIOUS PLUMBING REVIEW:       1. SHT A-1 INDICATES GAS EQUIPMENT IN THE KITCHEN. A   SEPARATE GAS PERMIT IS REQUIRED. SUBMIT THE FOLLOWING   INFORMATION:   ****NO RESPONSE, NOT ADDRESSED.       A. SUBMIT AN ISOMETRIC DRAWING THAT   CLEARLY SHOWS ALL CUT SECTIONS OF PIPE   AND CORRESPONDING LENGTHS PER FBC-2004   FUEL GAS CODE.   ****NO RESPONSE, NOT ADDRESSED.       B. SHOW TYPE OF PIPING MATERIAL BEING   INSTALLED, ALL PIPE SIZES, (AND THE EDH   NUMBER OF CORRUGATED STAINLESS STEEL   TUBING FOR EACH PIPE SIZE IF BEING USED.   ****NO RESPONSE, NOT ADDRESSED.       C. TYPE OF GAS, (LP OR NATURAL).   ****NO RESPONSE, NOT ADDRESSED.       D. BTU LOAD OF EACH APPLIANCE AND THE   TOTAL BTU LOAD ON THE SYSTEM. REFER TO   THE FBC-2004 FUEL GAS CODE SECS. 401.8   THRU 402.6.1 AND TABLES 402.4(1) THRU   402.4(33).   ****NO RESPONSE, NOT ADDRESSED.       E. SHOW THE DISTANCE FROM THE POINT OF   DELIVERY, (METER), TO THE MOST REMOTE   OUTLET IN THE BUILDING AND/OR SYSTEM PER   FBC-2004 FUEL GAS CODE APPENDIX A - USE   OF CAPACITY TABLES A.3.1(4).   ****NO RESPONSE, NOT ADDRESSED.       F. SUBMIT CALCULATIONS FOR COMBUSTION   AIR (IF APPLICABLE) PER FBC-2004 FUEL   GAS CODE SECTION 304.   ****NO RESPONSE, NOT ADDRESSED.       G. INDICATE THE DELIVERY PRESSURE (PSI)   PER FBC-2004 FUEL GAS CODE SEC. 402.2.   NATURAL GAS SPECIFY .5 PSI OR 2 PSI. IF 2 PSI SHOW THE   LOCATION OF THE REGULATORS, SUBMIT MANUF.   SPECIFICATIONS FOR THE REGULATORS AND IF THE REGULATORS   ARE VENTED, INDICATE THE MATERIAL OF THE VENT AND SHOW   THE PIPING LOCATION.   ****NO RESPONSE, NOT ADDRESSED.       H. SUBMIT A DETAIL SHOWING THE TYPE,   LOCATION, SIZE AND TERMINATION OF THE   GAS VENTS PER FBC-2004 FUEL GAS CODE   SECS. 502 THRU 505.   ****NO RESPONSE, NOT ADDRESSED.       I. SUBMIT MANUFACTURE SHEETS FOR ALL GAS   EQUIPMENT TO VERIFY COMPLIANCE WITH   STANDARDS NFPA 54, NFPA 58, AND THE   FBC-2004 FUEL GAS CODE SEC 402.2.   ****NO RESPONSE, NOT ADDRESSED.       J. CLEARLY SHOW THE LOCATION AND CAP-   ACITY OF LP TANK(S), TYPE OF TANK (DOT   OR ASME), THE DISTANCE OF THE TANK FROM   THE BUILDING AND ADJACENT PROPERTY LINES   THE DISTANCE OF THE TANK FROM ALL SOUR-   CES OF IGNITION, OTHER CONTAINERS, BUILD   INGS, AND THE LOCATION OF ANY BUILDING   OPENINGS BELOW THE RELIEF VALVE OF THE   TANK PER NFPA 58, TABLE 3-2.2.2.   ****NO RESPONSE, NOT ADDRESSED.       K. CLEARLY INDICATE ON THE PLAN IF THE   LP TANK IS ABOVE OR BELOW GROUND, AND   SHOW REQUIRED PROTECTION OF THE TANK AND APPURTENANCES   PER NFPA 58. IF THE TANK   IS BELOW GROUND THE CONTAINER SHALL BE   SECURILY ANCHORED PER NFPA 58 SECTION   3-2.2.7(H).   ****NO RESPONSE, NOT ADDRESSED.       L. EMERGENCY HOOD SHUT DOWN SHUT OFF   VALVE TO BE BELOW CEILING. MANUAL SHUT   OFF VALVE TO BE UPSTREAM. UNION TO BE   DOWN STREAM OF MANUAL VALVE.   ****NO RESPONSE, NOT ADDRESSED.       WHEN RESUBMITTING PLANS PLEASE INDICATE   THE REVISION & REMOVE & REPLACE ANY   PAGES AS NECESSARY. A TRANSMITTAL LETTER   LISTING THE ORIGINAL REVIEW COMMENT NUM-   BER, WITH A DESCRIPTION OF THE REVISION   MADE, IDENTIFYING THE SHEET OR SPECIFICA   TION PAGE WHERE THE CHANGES CAN BE FOUND   WILL HELP TO EXPEDITE YOUR PERMIT. THANK   YOU FOR YOUR ANTICIPATED COOPERATION.       REVIEW BY KEN STEVENS   (561) 805-6721   FAX (561) 805-6731   E-MAIL [email protected] Review Stop I INCOMING/PROCESSING Rev No 7 Status N Date 2009-12-01 Cont ID   Sent By lmartine Date 2009-11-24 Time 10:47 Rev Time 0.00 Received By lmartine Date 2009-11-24 Time 10:47 Sent To   Notes 2009-12-01 10:54:02 C--4 Review Stop I INCOMING/PROCESSING Rev No 6 Status N Date 2009-09-15 Cont ID   Sent By kstevens Date 2009-09-15 Time 17:27 Rev Time 0.00 Received By kstevens Date 2009-09-15 Time 17:27 Sent To   Notes 2009-09-15 17:29:53 SENT TO C-32. Review Stop I INCOMING/PROCESSING Rev No 5 Status N Date 2009-07-16 Cont ID   Sent By rmcdouga Date 2009-07-16 Time 16:45 Rev Time 0.00 Received By rmcdouga Date 2009-07-16 Time 16:45 Sent To   Notes 2009-07-16 16:45:27 TO C25 Review Stop I INCOMING/PROCESSING Rev No 4 Status N Date 2009-05-14 Cont ID   Sent By shill Date 2009-05-14 Time 11:58 Rev Time 0.00 Received By shill Date 2009-05-14 Time 11:57 Sent To   Notes 2009-05-14 11:58:18 TO COMMERCIAL BOARD #23     Review Stop I INCOMING/PROCESSING Rev No 3 Status N Date 2007-09-28 Cont ID   Sent By adarroug Date 2007-09-28 Time 09:47 Rev Time 0.00 Received By adarroug Date 2007-09-28 Time 09:47 Sent To   Notes 2007-10-18 08:59:43 TO "COMM" BD#12 2007-09-28 09:48:01 WAITING FOR "COMM" BD Review Stop I INCOMING/PROCESSING Rev No 2 Status N Date 2007-03-23 Cont ID   Sent By adarroug Date 2007-03-23 Time 09:00 Rev Time 0.00 Received By adarroug Date 2007-03-23 Time 09:00 Sent To   Notes 2007-03-23 09:03:55 TO "COMM" BD#16 Review Stop I INCOMING/PROCESSING Rev No 1 Status N Date 2007-01-03 Cont ID   Sent By kstevens Date 2007-01-03 Time 09:55 Rev Time 0.00 Received By kstevens Date 2006-11-02 Time 10:34 Sent To   Notes 2006-11-02 10:36:19 TO "COMM" BD#6 Review Stop L LANDSCAPING Rev No 2 Status P Date 2009-07-17 Cont ID   Sent By rkussner Date 2009-07-17 Time 13:27 Rev Time 0.00 Received By rkussner Date 2009-07-17 Time 13:27 Sent To PC Notes ***NONE*** Review Stop L LANDSCAPING Rev No 1 Status F Date 2009-05-29 Cont ID   Sent By rkussner Date 2009-05-29 Time 14:04 Rev Time 0.00 Received By rkussner Date 2009-05-29 Time 14:04 Sent To   Notes 2009-05-29 14:40:28 ***LANDSCAPE REVIEW FAILED***       PLEASE PROVIDE RESPONSES TO REVIEW COMMENTS IN WRITTEN   FORMAT.       1. PURSUANT TO SECTION 94-444 (B), OUTDOOR MECHANICAL   EQUIPMENT SHALL NOT BE PERMITTED UNLESS APPROPRIATE   SCREENING IS PROVIDED. THE EQUIPMENT ENCLOSURE SHALL   OPEN TO THE REAR (NORTH SIDE) OF THE STRUCTURE. THE   CORNER ON THE SOUTH SIDE SHALL BE CUT OUT AND LANDCAPED   WITH VERTICAL LANDSCAPE ELEMENTS SUCH AS A PALM   GROUPING WITH UNDERPLANTING.       2. PURSUANT TO SECTION 94-443 (C)(2), SHADE TREES SHALL   BE PLANTED AT 30 FOOT INTERVALS IN THE REQUIRED   LANDSCAPE BUFFER THAT SEPARATES THE VEHICULAR USE AREA   FROM ADJACENT RIGHTS-FOF-WAY. AN ADDITIONAL TREE IS   REQUIRED ALONG THE SOUTH PERIMETER OF THE SITE ON THE   EAST SIDE OF THE EAST ACCESS POINT.       3. TREES IN TERMINAL LANDSCAPE ISLANDS SHALL BE   CENTERED WITHIN THE ISLAND TO PROVIDE SHADE OVER THE   PARKING STALL. PLEASE ADD TWO ADDITIONAL SABAL PALMS OR   A SHADE TREE IN THE LANDSCAPE ISLAND ON THE EAST SIDE   OF THE EQUIPMENT ENCLOSURE. OTHERWISE, THE THREE PALMS   COULD BE SHIFTED TOWARD THE SOUTH AND AN ADDITIONAL   PERIMETER SILVER BUTTONWOOD TREE CAN BE ADDED ALONG THE   NORTH PERIMETER OF THE SITE. THE SPACING OF THE TREES   ALONG THE NORTH PERIMETER CANNOT EXCEED 30 FEET. THE   TREES SHALL BE EQUALLY SPACED.       4. THE BLACK OLIVE TREE ALONG THE WEST PERIMETER SHALL   BE REMOVED AND REPLACED. IT IS NOT A FLORIDA #1 GRADE   TREE AND IS IN POOR HEALTH.       5, IN KEEPING WITH XERISCAPE GUIDELINES, GROUND COVER   SHALL BE PLANTED IN THE SMALL AREAS THROUGHOUT THE SITE   INSTEAD OF SOD. THE PLANTING WILL REQUIRE LESS WATER   AND MAINTENANCE THAN SOD.       6, THE PROPOSED HEDGE ALONG THE EAST PERIMETER OF THE   SITE SHALL BE PLANTED ALONG THE INTERIOR PERIMETER OF   THE LANDSCAPE BUFFER WITH GROUND COVER PLANTED ALONG   THE STREET SIDE.       IF YOU HAVE ANY QUESTIONS, PLEASE CONTACT ROBERT   KUSSNER @ (561) 822-1462.     Review Stop M MECHANICAL (A/C) Rev No 5 Status P Date 2009-10-01 Cont ID   Sent By rregueir Date 2009-10-01 Time 09:43 Rev Time 0.00 Received By rregueir Date 2009-09-30 Time 16:10 Sent To   Notes 2009-10-01 09:44:18 SEPARATE PLANS AND APPLICATIONS REQUIRED FOR THE   FOLLOWING:       -HOOD   -HOOD SUPPRESSION   -WALK-IN COOLER       IF YOU HAVE ANY QUESTIONS PLEASE CONTACT:   RONALD J. REGUEIRO   561.805.6719   [email protected] Review Stop M MECHANICAL (A/C) Rev No 4 Status P Date 2009-06-09 Cont ID   Sent By rregueir Date 2009-06-09 Time 17:03 Rev Time 0.00 Received By rregueir Date 2009-06-09 Time 15:41 Sent To   Notes 2009-06-09 17:03:38 SEE EXCEPTIONS NOTED ON PLANS. Review Stop M MECHANICAL (A/C) Rev No 3 Status F Date 2007-10-23 Cont ID   Sent By tgordon Date 2007-10-23 Time 11:27 Rev Time 0.45 Received By tgordon Date 2007-10-23 Time 11:27 Sent To   Notes 2007-10-23 11:50:32 PLAN REVIEW UNDER THE 2004 FLORIDA BUILDING CODE &   REFERENCED CODES WITH 05, 06 REVISIONS, CITY OF WEST   PALM BEACH AMENDMENTS TO CHAPTER 1 (W.P.B.), FLORIDA   ADMINISTRATIVE CODE (F.A.C.), AND FLORIDA STATUTES   (F.S.).       *FOR PLAN REVIEW ONLY NOT FOR PERMIT*   *** DENIED ***       1) AS NOTED IN LAST TWO REVIEWS 11-3-06 AND 4-2-07 NOTE   #5. THE TWO AUXILIARY DRAIN LINES (EM) NEED TO   DISCHARGE TO A CONSPICUOUS LOCATION, PER 2004 FBC/M   307.2.3, PLEASE CORRECT. (THE BACK OF THE BUILDING IS   NOT A CONSPICUOUS LOCATION).       2) AS NOTED IN LAST TWO REVIEWS 11-3-06 AND 4-2-07 NOTE   #6. PLEASE SUBMIT ENERGY CALCULATIONS, PER 2004 FBC   13-101.1.1. (BE ADVISED A COMPLETE REVIEW CAN NOT BE   DONE WITHOUT THIS).       3) AS NOTED IN LAST TWO REVIEWS 11-3-06 AND 4-2-07 NOTE   #7. PLEASE SUBMITCOOLING LOAD CALCULATIONS, PER 2004   FBC 13-407.1.ABC.1. (BE ADVISED A COMPLETE REVIEW CAN   NOT BE DONE WITHOUT THIS).       4) PLEASE SIZE THE RETURN AIR DUCT TO OFFICE, SEE W.P.B   AMEND. 106.3.5.4 (10).       5) PLEASE SIZE THE TWO FRESH AIR DUCTS TO THE AHU'S,   SEE W.P.B. AMEND. 106.3.5.4 (10).       6) THE A/C EQUIPMENT LISTING IS SHOWING THE TWO SAME   SYSTEMS, BUT WITH DIFFERENT SENSIBLE, LATENT, AND TOTAL   BTU,S PLEASE CORRECT OR EXPLAIN, SEE W.P.B. AMEND.   106.3.5.4 (10).       MECHANICAL PLAN REVIEW BY;   TOM GORDON (561) 805-6729   E-MAIL; [email protected] Review Stop M MECHANICAL (A/C) Rev No 2 Status F Date 2007-04-02 Cont ID   Sent By tgordon Date 2007-04-02 Time 08:04 Rev Time 0.30 Received By tgordon Date 2007-04-02 Time 08:04 Sent To   Notes 2007-04-02 08:16:22 *FOR PLAN REVIEW ONLY NOT FOR PERMIT*   *** DENIED ***       1) ALL OF THE FOLLOWING CORRECTIONS WERE REQUESTED IN   THE LAST REVIEW 11-3-06 AND STILL NEED TO BE   CORRECTED.       2) NEED TO SHOW THE SIZES OF THE A/C AIR DUCTS, SUPPLY   TRUNK LINE, RETURN TRUNK LINE, AND HALF THE SUPPLY   BRANCH LINES, SEE YELLOW HIGH LIGHTS ON MECH. PLANS.       3) NEED THE SIZE OF THE RETURN AIR GRILLS.       4) PROVIDE RETURN AIR TO THE OFFICE, PER 2004 FBC/M   601.4.       5) THE TWO AUXILIARY DRAIN LINES (EM) NEED TO DISCHARGE   TO A CONSPICUOUS LOCATION, PER 2004 FBC/M 307.2.3,   PLEASE CORRECT.       6) PLEASE SUBMIT ENERGY CALCULATIONS, PER 2004 FBC   13-101.1.1.       7) PLEASE SUBMITCOOLING LOAD CALCULATIONS, PER 2004   FBC 13-407.1.ABC.1 .       8) NEED THE JOB ADDRESS ON EACH PLAN.       9) NEED TO SHOW AN EQUIPMENT LISTING ON MECHANICAL   PLANS WITH A/C EQUIPMENT MANUFACTURES NAME,MODEL   NUMBERS, TOTAL AND SENSIBLE BTU'S, SEER, AND ALL OTHER   PERTINENT INFORMATION FOR THE A/C SYSTEMS.       MECHANICAL PLAN REVIEW BY;   TOM GORDON (561) 805-6729. Review Stop M MECHANICAL (A/C) Rev No 1 Status F Date 2006-11-03 Cont ID   Sent By tgordon Date 2006-11-03 Time 11:44 Rev Time 0.45 Received By tgordon Date 2006-11-03 Time 11:44 Sent To   Notes 2006-11-03 12:15:26 *FOR PLAN REVIEW ONLY NOT FOR PERMIT*   *** DENIED ***   1) SHOW THE LOCATION OF THE TWO A/C CONDENSER UNITS AND   THE ONE WALK IN COOLER CONDENSER UNIT ON THE MECHANICAL   PLANS.       2) NEED TO SHOW THE SIZES OF THE A/C AIR DUCTS, SUPPLY   TRUNK LINE, RETURN TRUNK LINE, AND HALF THE SUPPLY   BRANCH LINS, SEE HIGH LIGHTS ON MECH. PLANS.       3) NEED THE SIZE OF THE RETURN AIR GRILLS.       4) PROVIDE RETURN AIR TO THE OFFICE, PER 2004 FBC/M   601.4.       5) THE TWO AUXILIARY DRAIN LINES (EM) NEED TO DISCHARGE   TO A CONSPICUOUS LOCATION, PER 2004 FBC/M 307.2.3,   PLEASE CORRECT.       6) PLEASE SUBMIT ENERGY CALCULATIONS, PER 2004 FBC   13-101.1.1.       7) PLEASE SUBMITCOOLING LOAD CALCULATIONS, PER 2004   FBC 13-407.1.ABC.1 .       8) NEED THE JOB ADDRESS ON EACH PLAN.       9) NEED TO ALSO SHOW THE SENSIBLE BTU'S AND CFM'S FOR   THE A/C SYSTEMS.       MECHANICAL PLAN REVIEW BY;   TOM GORDON (561) 805-6729. Review Stop P PLUMBING Rev No 7 Status P Date 2009-12-16 Cont ID   Sent By kstevens Date 2009-12-16 Time 15:14 Rev Time 0.00 Received By kstevens Date 2009-12-16 Time 15:14 Sent To   Notes 2009-12-16 15:14:48 PLANS STILL CODE COMPLIANT. -- NO CONTRACTOR SIGNED ON   AT THIS TIME. Review Stop P PLUMBING Rev No 6 Status F Date 2009-09-22 Cont ID   Sent By kstevens Date 2009-09-22 Time 09:23 Rev Time 0.00 Received By kstevens Date 2009-09-22 Time 09:23 Sent To   Notes 2009-09-22 09:25:41 IRRIGATION PLANS APPROVED WITH PROVISO: DOUBLE DETECTOR   NOT APPROVED. AN RPZV BACKFLOW IS REQUIRED AND SHALL BE   INSTALLED BY A LICENSED PLUMBING CONTRACTOR. PER CILB   PBC. PLANS WILL REMAIN IN FAILED STATUS UNTIL BLD-COM   PERMIT IS APPLIED FOR BY LICENSED CONTRACTOR. Review Stop P PLUMBING Rev No 5 Status F Date 2009-08-05 Cont ID   Sent By kstevens Date 2009-08-05 Time 15:47 Rev Time 0.00 Received By kstevens Date 2009-08-05 Time 15:48 Sent To   Notes 2009-08-10 15:49:26 PLANS ARE CODE COMPLIANT BUT WILL REMAIN IN FAILED   STATUS PENDING APPLICATION FOR PERMIT BY LICENSED   CONTRACTOR. Review Stop P PLUMBING Rev No 4 Status F Date 2009-05-29 Cont ID   Sent By kstevens Date 2009-05-29 Time 13:15 Rev Time 0.00 Received By kstevens Date 2009-05-29 Time 13:15 Sent To   Notes 2009-05-29 13:52:26 DENIED   REFERENCE:   FBC-2007 W/2009 SUPPLEMENTS   FBC-2007 PLUMBING   FBC-2007 FUEL GAS   FBC-2007 BUILDING   FBC-2007 CHAPTER 1 (ADMIN)   FBC-2007 CHAPTER 11           1. SHT SP-1 CODE REFERENCE SHALL INCLUDE THE 2009   SUPPLEMENTS. SECTION 106.1.1.       2. SHT A-2 THE FILTERS REFERENCED SHALL MEET THE   REQUIREMENTS OF NSF-42. PLEASE SUBMIT MANUF.   SPECIFICATIONS FOR THE FILTERS. SECTIONS 106.1.2 &   611.1.       3. SHT A-2 ROOM FINISH SCHEDULE FOR THE TOILET ROOM   INDICATES PANTED WALLS. WALLS WITHIN 2 FEET OF THE   WATER CLOSET SHALL HAVE A SMOOTH, HARD, NONABSORBENT   SURFACE. PAINTED SURFACES DOES NOT MEET THE "HARD"   REQUIREMENT. SECTION 1210.2.       4. SHT A-2 TOILET ROOM ELEVATIONS. PLEASE INCLUDE THE   REQUIRMENT FOR SECTION 11-4.16.5 FLUSH CONTROLS.       5. SHT A-4 GUTTER FOR FLAT ROOF, (TOTAL AREA WITH   VERTICAL WALL CONTRIBUTION 1102 FS), REQUIRES A 7INCH   GUTTER AT .5 % SLOPE OR 6 INCH AT 1& SLOPE. TABLE   1106.6. PLEASE INDICATE SLOPE REQUIRED ON GUTTER OR   INDICATE 7 INCH GUTTER.       6. SHT A-4 GUTTERS SHALL BE SIZED BY TABLE 1106.6. ROOF   PLAN NOTES #5 INDICATES 1106.7. THIS IS FOR OVERFLOW   SCUPPERS. PLEASE UPDATE TABLE REFERENCE FOR GUTTERS.       7. SHT P-2 SANITARY ISOMETRIC RISER DIAGRAM. MINIMUM 4"   PIPE IS REQUIRED UPSTREAM OF THE 1ST HAND SINK, (BY THE   KITCHEN). THE FIXTURE UNIT COUNT IS 41 FU AT THAT   POINT. TABLE 710.1(1).       8 THE FOLLOWING INFORMATION IS REQUIRED FOR THE   SEPARAGE GAS PERMIT:       A. SUBMIT AN ISOMETRIC DRAWING THAT   CLEARLY SHOWS ALL CUT SECTIONS OF PIPE   AND CORRESPONDING LENGTHS PER FBC-2007   FUEL GAS CODE. -- THE SECTION FROM THE WALL TO THE   METER IS NOT INDICATED.       B. TYPE OF GAS, (LP OR NATURAL). -- NOT INDICATED ON   PLANS. SITE PLANS SHOWS A 1000 GAL PROPANE TANK BUT   NOTE ON SHT P-2 INDICATES TABLE 402.4(2) WHICH IS A   NATURAL GAS TABLE. PLEASE CLARIFY.       C. SHOW THE DISTANCE FROM THE POINT OF   DELIVERY, (METER), TO THE MOST REMOTE   OUTLET IN THE BUILDING AND/OR SYSTEM PER   FBC-2007 FUEL GAS CODE APPENDIX A - USE   OF CAPACITY TABLES A.3.1(4). -- TO BE VERIFIED WHEN   COMMENT 8(A) IS ADDRESSED.       D. SUBMIT MANUFACTURE SHEETS FOR ALL GAS   EQUIPMENT TO VERIFY COMPLIANCE WITH   STANDARDS NFPA 54, NFPA 58, AND THE   FBC-2007 FUEL GAS CODE SEC 402.2.       WHEN RESUBMITTING PLANS PLEASE INDICATE   THE REVISION & REMOVE & REPLACE ANY   PAGES AS NECESSARY. A TRANSMITTAL LETTER   LISTING THE ORIGINAL REVIEW COMMENT NUMBER,   WITH A DESCRIPTION OF THE REVISION MADE,   IDENTIFYING THE SHEET OR SPECIFICATION   PAGE WHERE THE CHANGES CAN BE FOUND   WILL HELP TO EXPEDITE YOUR PERMIT. REMOVE   ALL VOID SHEETS FROM ALL PLANS AND PLACE   ONE SET OF THEM LOOSELY ON TOP OF THE   COLLATED PLANS TO BE REVIEWED.   THANK YOU FOR YOUR ANTICIPATED COOPERATION.       REVIEW BY KEN STEVENS   (561) 805-6721   FAX (561) 805-6731   E-MAIL [email protected]     Review Stop P PLUMBING Rev No 3 Status F Date 2007-12-03 Cont ID   Sent By kstevens Date 2007-12-03 Time 06:58 Rev Time 0.00 Received By kstevens Date 2007-12-01 Time 14:25 Sent To   Notes 2007-12-03 07:42:39 DENIED   REFERENCE: FBC-2004 PLUMBING   FBC-2004 FUEL GAS   FBC-2004 CHAPTER 1   FBC-2004 CHAPTER 11       FROM PREVIOUS REVIEW:   ******FROM PREVIOUS REVIEWS.       1.OK       2. SUBMIT A DETAIL FOR THE TOILET ROOM. SHOW COMPLIANCE   WITH SECTIONS 11-4.16, 11-4.19, 11-4.22 AND ALL   SUBSECTIONS.   ****NO RESPONSE, NOT ADDRESSED.   SHOW THE FOLLOWING:   ____FOR W/C'S:   A. OK   B. OK   C. OK   D. 11-4.16.5 FLUSH CONTROLS   ******RESPONSE NOTED, NOT ADDRESSED   E. OK   ____FOR LAVS:   A. OK   B. 11-4.19.5 FAUCETS   ******RESPONSE NOTED, NOT ADDRESSED       3. OK   4. OK   5. OK   6. OK       7. SHT P-1 THE GREASE PLUMBING RISER DOES NOT MEET   CODE. THE 3 COMPARTMENT SINK AND THE HAND SINK ARE NOT   VENTED. (MISLABELED AS LAVS). ALSO EQUIPMENT AND   FIXTURES UTILIZED FOR THE STORAGE, PREPARATION AND   HANDLING OF FOOD SHALL DISCHARGE THROUGH AN INDIRECT   PIPE BY MEANS OF AN AIR GAP. (A FLOOR SINK WOULD BE   REQUIRED). SECTIONS 802.1.1 AND 901.2.1.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT A RUNNING TRAP IS NOT   APPROVED AND A SEPARATE FLOOR SINK IS REQUIRED FOR THE   3 COMPARTMENT SINK. (SEE RED LINE CORRECTION EXAMPLE   SHOWN ON ONE SET OF PLANS). THE MOP SINK AND ICE MAKER   DRAINAGE IS NOT SHOWN ON THE RISER DIAGRAM. FLOOR   DRAINS ARE NOT APPROVED INDIRECT WASTE RECEPTORS. A   FLOOR SINK OR HUB DRAIN IS REQUIRED PER SECTIONS 802.3   & 802.3.2. FLOOR SINKS SHALL BE INSTALLED UNDER THE   FIXTURE SO THEY WILL NOT BECOME A TRIPPING HAZARD.       8. SUBMIT A WATER RISER DIAGRAM. SHOW ALL PIPE SIZES,   VALVES, AND REQUIRED WATER HAMMER ARRESTORS, (ICE   MACHINE). SECTIONS 106.3.5.1.3 & 604.9.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT ALL PIPE SIZES ARE NOT SHOWN,   AND PLEASE CLARIFY MARKINGS ON THE RISER DIAGRAM.       9. OK       10. SHT A-1 INDICATES GAS EQUIPMENT IN THE KITCHEN. A   SEPARATE GAS PERMIT IS REQUIRED. SUBMIT THE FOLLOWING   INFORMATION:   ****NO RESPONSE, NOT ADDRESSED.       A. SUBMIT AN ISOMETRIC DRAWING THAT   CLEARLY SHOWS ALL CUT SECTIONS OF PIPE   AND CORRESPONDING LENGTHS PER FBC-2004   FUEL GAS CODE.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE CORRESPONDING LENGHTS OF   EACH CUT SECTION HAVE NOT BEEN SUBMITTED, PLEASE   CLARIFY THE MARKINGS ON THE RISER DIAGRAM.       B. SHOW TYPE OF PIPING MATERIAL BEING   INSTALLED, ALL PIPE SIZES, (AND THE EDH   NUMBER OF CORRUGATED STAINLESS STEEL   TUBING FOR EACH PIPE SIZE IF BEING USED.   ****NO RESPONSE, NOT ADDRESSED.   ******NO RESPONSE, NOT INDICATED ON RISER DIAGRAM OR   ADJOINING NOTES.       C. OK - LP   D. OK       E. SHOW THE DISTANCE FROM THE POINT OF   DELIVERY, (METER), TO THE MOST REMOTE   OUTLET IN THE BUILDING AND/OR SYSTEM PER   FBC-2004 FUEL GAS CODE APPENDIX A - USE   OF CAPACITY TABLES A.3.1(4).   ****NO RESPONSE, NOT ADDRESSED.   ******NO RESPONSE, NOT ADDRESSED.       F. OK       G. INDICATE THE DELIVERY PRESSURE (PSI)   PER FBC-2004 FUEL GAS CODE SEC. 402.2.   NATURAL GAS SPECIFY .5 PSI OR 2 PSI. IF 2 PSI SHOW THE   LOCATION OF THE REGULATORS, SUBMIT MANUF.   SPECIFICATIONS FOR THE REGULATORS AND IF THE REGULATORS   ARE VENTED, INDICATE THE MATERIAL OF THE VENT AND SHOW   THE PIPING LOCATION.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE MANUF. SPECIFICATIONS DO   NOT SET THE DELIVERY PRESSURE. PLEASE ADDRESS COMMENT.       H. OK       I. SUBMIT MANUFACTURE SHEETS FOR ALL GAS   EQUIPMENT TO VERIFY COMPLIANCE WITH   STANDARDS NFPA 54, NFPA 58, AND THE   FBC-2004 FUEL GAS CODE SEC 402.2.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT MANUF. SHEETS NOT SUBMITTED.       J. OK       K. CLEARLY INDICATE ON THE PLAN IF THE   LP TANK IS ABOVE OR BELOW GROUND, AND   SHOW REQUIRED PROTECTION OF THE TANK AND APPURTENANCES   PER NFPA 58. IF THE TANK   IS BELOW GROUND THE CONTAINER SHALL BE   SECURILY ANCHORED PER NFPA 58 SECTION   3-2.2.7(H).   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE ISOMETRIC ON SHT P-1   INDICATES AN ABOVE GROUND TANK, AND THE SITE PLAN AS   WELL AS THE CIVIL SHEETS INDICATE AN UNDERGROUND TANK.   PLEASE CORRELATE.       L. EMERGENCY HOOD SHUT DOWN SHUT OFF   VALVE TO BE BELOW CEILING. MANUAL SHUT   OFF VALVE TO BE UPSTREAM. UNION TO BE   DOWN STREAM OF MANUAL VALVE.   ****NO RESPONSE, NOT ADDRESSED.   ******RESPONSE NOTED, BUT THE UNION IS NOT SHOWN, AND   MANUF. SPECIFICATION SHEETS ARE REQUIRED FOR THE ANSUL   VALVE SHOWING THAT THE VALVE IS LISTED FOR OUTSIDE   USE.       **********NEW COMMENTS**********       1B. PLEASE SEE ELECTRICAL COMMENTS #3 & #4 CONCERNING   TITLE BLOCKS, SEALS, PRINTED NAMES REQUIRE BY THE   FLORIDA ADMINISTRATIVE CODE AND THE FLORIDA STATUTES.   ******NO RESPONSE, AND THE SP-1 SHEET IS NOT SIGNED,   SEALED, OR DATED. SHT LS-1 SEAL IS NOT APPROVED. PER   FAC 61G1-16.002 & FS 481.306. SHTS LS-1 & LS-2 ARE NOT   SIGNED, SEALED OR DATED.       *****NEW COMMENTS 3RD REVIEW*****       1C. SHT P-1 SHOWS THE CLEANOUTS AT THE GREASE LINE &   SANT. LINES NEAR THE GREASE INTERCEPTOR & THE BUILDING   SEWER LOCATED UNDER AN A/C COMPRESSOR & IN A WALL.   CLEANOUTS SHALL BE ACCESSIBLE PER TABLE 708.9. ALSO THE   A/C UNITS ARE LOCATED OVER THE TOP OF THE GREASE   INTERCEPTOR WHICH ALSO REQUIRES ACCESS TO SERVICE.   PLEASE CLARIFY. SECTION 106.1.1.       2C. SHT P-1 WATER ISOMETRIC RISER DIAGRAM DOES NOT SHOW   WATER SUPPLY TO THE MOP SINK NOR TO THE ICE MAKER,   (WHICH REQUIRES A WATER HAMMER ARRESTOR). PLEASE   CLARIFY. SECTION 106.1.1.       WHEN RESUBMITTING PLANS PLEASE INDICATE   THE REVISION & REMOVE & REPLACE ANY   PAGES AS NECESSARY. A TRANSMITTAL LETTER   LISTING THE ORIGINAL REVIEW COMMENT NUM-   BER, WITH A DESCRIPTION OF THE REVISION   MADE, IDENTIFYING THE SHEET OR SPECIFICA   TION PAGE WHERE THE CHANGES CAN BE FOUND   WILL HELP TO EXPEDITE YOUR PERMIT. THANK   YOU FOR YOUR ANTICIPATED COOPERATION.       REVIEW BY KEN STEVENS   (561) 805-6721   FAX (561) 805-6731   E-MAIL [email protected] Review Stop P PLUMBING Rev No 2 Status F Date 2007-04-09 Cont ID   Sent By kstevens Date 2007-04-09 Time 17:39 Rev Time 0.00 Received By kstevens Date 2007-04-09 Time 17:39 Sent To   Notes 2007-04-09 17:50:33 DENIED   REFERENCE: FBC-2004 PLUMBING   FBC-2004 FUEL GAS   FBC-2004 CHAPTER 1   FBC-2004 CHAPTER 11       FROM PREVIOUS REVIEW:       1. SHT C-1 INDICATES "NEW CONVENIENCE STORE/PROPOSED   BUILDING", BUT NOTES ON SHT A-1 INDICATE AN EXISTING   BUILDING. PLEASE CLARIFY. SECTION 106.1.1.   ****NO RESPONSE, NOT ADDRESSED.       2. SUBMIT A DETAIL FOR THE TOILET ROOM. SHOW COMPLIANCE   WITH SECTIONS 11-4.16, 11-4.19, 11-4.22 AND ALL   SUBSECTIONS.   ****NO RESPONSE, NOT ADDRESSED.   SHOW THE FOLLOWING:   ____FOR W/C'S:   A. 11-4.16.2 CLEAR FLOOR SPACE   B. 11-4.16.3 HEIGHT   C. 11-4.16.4 GRAB BARS   D. 11-4.16.5 FLUSH CONTROLS   E. 11-4.16.6 DISPENSERS   ____FOR LAVS:   A. 11-4.19.4 EXPOSED PIPES & SURFACES   B. 11-4.19.5 FAUCETS       3. A GREASE INTERCEPTOR MAY BE REQUIRED. PLEASE CONTACT   LYNN MASSON, ENVIRONMENTAL COMPLIANCE MANAGER, PHONE   NUMBER (561) 822-2271, FAX (561) 822-2279, OR E-MAIL   [email protected]. WASTE ORD. 3434.   ****NO RESPONSE, NOT ADDRESSED.       4. PER TABLE 403.1 A DRINKING FOUNTAIN IS REQUIRED.   PLEASE INDICATE THE LOCATION ON THE FLOOR PLAN. SUBMIT   A DETAIL SHOWING COMPLIANCE WITH SECTION 11-4.15 AND   ALL SUBSECTIONS AS WELL AS SECTION 11-4.1.3(10)(A)   PROVISIONS FOR THOSE WHO HAVE DIFFICULTY BENDING OR   STOOPING. SHOW DRINKING FOUNTAIN ON THE SANT. AND WATER   RISER DIAGRAMS.   ****NO RESPONSE, NOT ADDRESSED.       5. SHT A-1 GENERAL NOTES #1. THE CODE ADOPTED IS   FBC-2004 NOT FBC-2001 AS INDICATED. PLEASE UPDATE YOUR   NOTES TO REFLECT THE CODE IN EFFECT.   ****NO RESPONSE, NOT ADDRESSED.       6. SHT P-1THE SANITARY PLUMBING RISER DOES NOT MEET   CODE. HORIZONTAL DRY VENTS ARE NOT APPROVED. SECTION   905.3. - THE 3" VENT UPSTREAM OF THE W/C IS NOT   REQUIRED. THE 2" VENT AT THE LAV IS SUFFICIENT. ****NO   RESPONSE, NOT ADDRESSED.       7. SHT P-1 THE GREASE PLUMBING RISER DOES NOT MEET   CODE. THE 3 COMPARTMENT SINK AND THE HAND SINK ARE NOT   VENTED. (MISLABELED AS LAVS). ALSO EQUIPMENT AND   FIXTURES UTILIZED FOR THE STORAGE, PREPARATION AND   HANDLING OF FOOD SHALL DISCHARGE THROUGH AN INDIRECT   PIPE BY MEANS OF AN AIR GAP. (A FLOOR SINK WOULD BE   REQUIRED). SECTIONS 802.1.1 AND 901.2.1.   ****NO RESPONSE, NOT ADDRESSED.       8. SUBMIT A WATER RISER DIAGRAM. SHOW ALL PIPE SIZES,   VALVES, AND REQUIRED WATER HAMMER ARRESTORS, (ICE   MACHINE). SECTIONS 106.3.5.1.3 & 604.9.   ****NO RESPONSE, NOT ADDRESSED.       9. AN RPZV BACKFLOW IS REQUIRED ON THE WATER SERVICE TO   THE BUILDING. SECTION 608.13.2.   ****NO RESPONSE, NOT ADDRESSED.       10. SHT A-1 INDICATES GAS EQUIPMENT IN THE KITCHEN. A   SEPARATE GAS PERMIT IS REQUIRED. SUBMIT THE FOLLOWING   INFORMATION:   ****NO RESPONSE, NOT ADDRESSED.       A. SUBMIT AN ISOMETRIC DRAWING THAT   CLEARLY SHOWS ALL CUT SECTIONS OF PIPE   AND CORRESPONDING LENGTHS PER FBC-2004   FUEL GAS CODE.   ****NO RESPONSE, NOT ADDRESSED.       B. SHOW TYPE OF PIPING MATERIAL BEING   INSTALLED, ALL PIPE SIZES, (AND THE EDH   NUMBER OF CORRUGATED STAINLESS STEEL   TUBING FOR EACH PIPE SIZE IF BEING USED.   ****NO RESPONSE, NOT ADDRESSED.       C. TYPE OF GAS, (LP OR NATURAL).   ****NO RESPONSE, NOT ADDRESSED.       D. BTU LOAD OF EACH APPLIANCE AND THE   TOTAL BTU LOAD ON THE SYSTEM. REFER TO   THE FBC-2004 FUEL GAS CODE SECS. 401.8   THRU 402.6.1 AND TABLES 402.4(1) THRU   402.4(33).   ****NO RESPONSE, NOT ADDRESSED.       E. SHOW THE DISTANCE FROM THE POINT OF   DELIVERY, (METER), TO THE MOST REMOTE   OUTLET IN THE BUILDING AND/OR SYSTEM PER   FBC-2004 FUEL GAS CODE APPENDIX A - USE   OF CAPACITY TABLES A.3.1(4).   ****NO RESPONSE, NOT ADDRESSED.       F. SUBMIT CALCULATIONS FOR COMBUSTION   AIR (IF APPLICABLE) PER FBC-2004 FUEL   GAS CODE SECTION 304.   ****NO RESPONSE, NOT ADDRESSED.       G. INDICATE THE DELIVERY PRESSURE (PSI)   PER FBC-2004 FUEL GAS CODE SEC. 402.2.   NATURAL GAS SPECIFY .5 PSI OR 2 PSI. IF 2 PSI SHOW THE   LOCATION OF THE REGULATORS, SUBMIT MANUF.   SPECIFICATIONS FOR THE REGULATORS AND IF THE REGULATORS   ARE VENTED, INDICATE THE MATERIAL OF THE VENT AND SHOW   THE PIPING LOCATION.   ****NO RESPONSE, NOT ADDRESSED.       H. SUBMIT A DETAIL SHOWING THE TYPE,   LOCATION, SIZE AND TERMINATION OF THE   GAS VENTS PER FBC-2004 FUEL GAS CODE   SECS. 502 THRU 505.   ****NO RESPONSE, NOT ADDRESSED.       I. SUBMIT MANUFACTURE SHEETS FOR ALL GAS   EQUIPMENT TO VERIFY COMPLIANCE WITH   STANDARDS NFPA 54, NFPA 58, AND THE   FBC-2004 FUEL GAS CODE SEC 402.2.   ****NO RESPONSE, NOT ADDRESSED.       J. CLEARLY SHOW THE LOCATION AND CAP-   ACITY OF LP TANK(S), TYPE OF TANK (DOT   OR ASME), THE DISTANCE OF THE TANK FROM   THE BUILDING AND ADJACENT PROPERTY LINES   THE DISTANCE OF THE TANK FROM ALL SOUR-   CES OF IGNITION, OTHER CONTAINERS, BUILD   INGS, AND THE LOCATION OF ANY BUILDING   OPENINGS BELOW THE RELIEF VALVE OF THE   TANK PER NFPA 58, TABLE 3-2.2.2.   ****NO RESPONSE, NOT ADDRESSED.       K. CLEARLY INDICATE ON THE PLAN IF THE   LP TANK IS ABOVE OR BELOW GROUND, AND   SHOW REQUIRED PROTECTION OF THE TANK AND APPURTENANCES   PER NFPA 58. IF THE TANK   IS BELOW GROUND THE CONTAINER SHALL BE   SECURILY ANCHORED PER NFPA 58 SECTION   3-2.2.7(H).   ****NO RESPONSE, NOT ADDRESSED.       L. EMERGENCY HOOD SHUT DOWN SHUT OFF   VALVE TO BE BELOW CEILING. MANUAL SHUT   OFF VALVE TO BE UPSTREAM. UNION TO BE   DOWN STREAM OF MANUAL VALVE.   ****NO RESPONSE, NOT ADDRESSED.       **********NEW COMMENTS**********       1B. PLEASE SEE ELECTRICAL COMMENTS #3 & #4 CONCERNING   TITLE BLOCKS, SEALS, PRINTED NAMES REQUIRE BY THE   FLORIDA ADMINISTRATIVE CODE AND THE FLORIDA STATUTES.       WHEN RESUBMITTING PLANS PLEASE INDICATE   THE REVISION & REMOVE & REPLACE ANY   PAGES AS NECESSARY. A TRANSMITTAL LETTER   LISTING THE ORIGINAL REVIEW COMMENT NUM-   BER, WITH A DESCRIPTION OF THE REVISION   MADE, IDENTIFYING THE SHEET OR SPECIFICA   TION PAGE WHERE THE CHANGES CAN BE FOUND   WILL HELP TO EXPEDITE YOUR PERMIT. THANK   YOU FOR YOUR ANTICIPATED COOPERATION.       REVIEW BY KEN STEVENS   (561) 805-6721   FAX (561) 805-6731   E-MAIL [email protected] Review Stop P PLUMBING Rev No 1 Status F Date 2007-01-03 Cont ID   Sent By kstevens Date 2007-01-03 Time 08:35 Rev Time 0.00 Received By kstevens Date 2007-01-03 Time 08:35 Sent To   Notes 2007-01-03 09:53:04 DENIED   REFERENCE: FBC-2004 PLUMBING   FBC-2004 FUEL GAS   FBC-2004 CHAPTER 1   FBC-2004 CHAPTER 11       1. SHT C-1 INDICATES "NEW CONVENIENCE STORE/PROPOSED   BUILDING", BUT NOTES ON SHT A-1 INDICATE AN EXISTING   BUILDING. PLEASE CLARIFY. SECTION 106.1.1.       2. SUBMIT A DETAIL FOR THE TOILET ROOM. SHOW COMPLIANCE   WITH SECTIONS 11-4.16, 11-4.19, 11-4.22 AND ALL   SUBSECTIONS.       3. A GREASE INTERCEPTOR MAY BE REQUIRED. PLEASE CONTACT   LYNN MASSON, ENVIRONMENTAL COMPLIANCE MANAGER, PHONE   NUMBER (561) 822-2271, FAX (561) 822-2279, OR E-MAIL   [email protected]. WASTE ORD. 3434.       4. PER TABLE 403.1 A DRINKING FOUNTAIN IS REQUIRED.   PLEASE INDICATE THE LOCATION ON THE FLOOR PLAN. SUBMIT   A DETAIL SHOWING COMPLIANCE WITH SECTION 11-4.15 AND   ALL SUBSECTIONS AS WELL AS SECTION 11-4.1.3(10)(A)   PROVISIONS FOR THOSE WHO HAVE DIFFICULTY BENDING OR   STOOPING. SHOW DRINKING FOUNTAIN ON THE SANT. AND WATER   RISER DIAGRAMS.       5. SHT A-1 GENERAL NOTES #1. THE CODE ADOPTED IS   FBC-2004 NOT FBC-2001 AS INDICATED. PLEASE UPDATE YOUR   NOTES TO REFLECT THE CODE IN EFFECT.       6. SHT P-1THE SANITARY PLUMBING RISER DOES NOT MEET   CODE. HORIZONTAL DRY VENTS ARE NOT APPROVED. SECTION   905.3. - THE 3" VENT UPSTREAM OF THE W/C IS NOT   REQUIRED. THE 2" VENT AT THE LAV IS SUFFICIENT.       7. SHT P-1 THE GREASE PLUMBING RISER DOES NOT MEET   CODE. THE 3 COMPARTMENT SINK AND THE HAND SINK ARE NOT   VENTED. (MISLABELED AS LAVS). ALSO EQUIPMENT AND   FIXTURES UTILIZED FOR THE STORAGE, PREPARATION AND   HANDLING OF FOOD SHALL DISCHARGE THROUGH AN INDIRECT   PIPE BY MEANS OF AN AIR GAP. (A FLOOR SINK WOULD BE   REQUIRED). SECTIONS 802.1.1 AND 901.2.1.       8. SUBMIT A WATER RISER DIAGRAM. SHOW ALL PIPE SIZES,   VALVES, AND REQUIRED WATER HAMMER ARRESTORS, (ICE   MACHINE). SECTIONS 106.3.5.1.3 & 604.9.       9. AN RPZV BACKFLOW IS REQUIRED ON THE WATER SERVICE TO   THE BUILDING. SECTION 608.13.2.       10. SHT A-1 INDICATES GAS EQUIPMENT IN THE KITCHEN. A   SEPARATE GAS PERMIT IS REQUIRED. SUBMIT THE FOLLOWING   INFORMATION:       A. SUBMIT AN ISOMETRIC DRAWING THAT   CLEARLY SHOWS ALL CUT SECTIONS OF PIPE   AND CORRESPONDING LENGTHS PER FBC-2004   FUEL GAS CODE.       B. SHOW TYPE OF PIPING MATERIAL BEING   INSTALLED, ALL PIPE SIZES, (AND THE EDH   NUMBER OF CORRUGATED STAINLESS STEEL   TUBING FOR EACH PIPE SIZE IF BEING USED.       C. TYPE OF GAS, (LP OR NATURAL).       D. BTU LOAD OF EACH APPLIANCE AND THE   TOTAL BTU LOAD ON THE SYSTEM. REFER TO   THE FBC-2004 FUEL GAS CODE SECS. 401.8   THRU 402.6.1 AND TABLES 402.4(1) THRU   402.4(33).       E. SHOW THE DISTANCE FROM THE POINT OF   DELIVERY, (METER), TO THE MOST REMOTE   OUTLET IN THE BUILDING AND/OR SYSTEM PER   FBC-2004 FUEL GAS CODE APPENDIX A - USE   OF CAPACITY TABLES A.3.1(4).       F. SUBMIT CALCULATIONS FOR COMBUSTION   AIR (IF APPLICABLE) PER FBC-2004 FUEL   GAS CODE SECTION 304.       G. INDICATE THE DELIVERY PRESSURE (PSI)   PER FBC-2004 FUEL GAS CODE SEC. 402.2.   NATURAL GAS SPECIFY .5 PSI OR 2 PSI. IF 2 PSI SHOW THE   LOCATION OF THE REGULATORS, SUBMIT MANUF.   SPECIFICATIONS FOR THE REGULATORS AND IF THE REGULATORS   ARE VENTED, INDICATE THE MATERIAL OF THE VENT AND SHOW   THE PIPING LOCATION.       H. SUBMIT A DETAIL SHOWING THE TYPE,   LOCATION, SIZE AND TERMINATION OF THE   GAS VENTS PER FBC-2004 FUEL GAS CODE   SECS. 502 THRU 505.       I. SUBMIT MANUFACTURE SHEETS FOR ALL GAS   EQUIPMENT TO VERIFY COMPLIANCE WITH   STANDARDS NFPA 54, NFPA 58, AND THE   FBC-2004 FUEL GAS CODE SEC 402.2.       J. CLEARLY SHOW THE LOCATION AND CAP-   ACITY OF LP TANK(S), TYPE OF TANK (DOT   OR ASME), THE DISTANCE OF THE TANK FROM   THE BUILDING AND ADJACENT PROPERTY LINES   THE DISTANCE OF THE TANK FROM ALL SOUR-   CES OF IGNITION, OTHER CONTAINERS, BUILD   INGS, AND THE LOCATION OF ANY BUILDING   OPENINGS BELOW THE RELIEF VALVE OF THE   TANK PER NFPA 58, TABLE 3-2.2.2.       K. CLEARLY INDICATE ON THE PLAN IF THE   LP TANK IS ABOVE OR BELOW GROUND, AND   SHOW REQUIRED PROTECTION OF THE TANK AND APPURTENANCES   PER NFPA 58. IF THE TANK   IS BELOW GROUND THE CONTAINER SHALL BE   SECURILY ANCHORED PER NFPA 58 SECTION   3-2.2.7(H).       L. EMERGENCY HOOD SHUT DOWN SHUT OFF   VALVE TO BE BELOW CEILING. MANUAL SHUT   OFF VALVE TO BE UPSTREAM. UNION TO BE   DOWN STREAM OF MANUAL VALVE.       REVIEW BY KEN STEVENS   (561) 805-6721   FAX (561) 805-6731   E-MAIL [email protected] Review Stop X PERMIT EXTENSION Rev No 1 Status N Date 2010-07-22 Cont ID   Sent By rbrown Date 2010-07-22 Time 18:55 Rev Time 0.00 Received By rbrown Date 2010-07-22 Time 18:55 Sent To   Notes 2010-07-22 18:55:53 PERMIT APPLICATION EXTENDED UNTIL 9/16/10. LETTER IN   FILE. Review Stop Z ZONING Rev No 5 Status P Date 2009-09-21 Cont ID   Sent By kdfreema Date 2009-09-21 Time 13:39 Rev Time 0.00 Received By kdfreema Date 2009-09-21 Time 13:39 Sent To   Notes ***NONE*** Review Stop Z ZONING Rev No 4 Status P Date 2009-06-11 Cont ID   Sent By kdfreema Date 2009-06-11 Time 11:02 Rev Time 0.00 Received By kdfreema Date 2009-06-11 Time 11:02 Sent To   Notes ***NONE*** Review Stop Z ZONING Rev No 3 Status F Date 2007-10-25 Cont ID   Sent By kdfreema Date 2007-10-25 Time 16:05 Rev Time 0.00 Received By kdfreema Date 2007-10-25 Time 16:05 Sent To   Notes 2007-10-25 16:52:13 ***FAILED***       1. PLEASE PROVIDE A RESPONSE TO ALL COMMENTS IN   WRITING.       2. A LETTER FROM THE CITY'S ENGINEERING SERVICES   DEPARTMENT MUST BE PROVIDED APPROVING THE NEW DUMPSTER   APPROACH CONFIGURATION.       3. THE DUMPSTER ENCLOSURE MUST BE LANDSCAPED ON ITS   EAST SIDE.       4. THE GENERATOR ENCLOSURE MUST BE LANDSCAPED ON ITS   SOUTH AND EAST SIDES.       5. THE GENERATOR ENCLOSURE DOORS MAY NOT OPEN INTO THE   HANDICAP ACCESS AISLE.       6. ALL PARKING ROWS MUST BE TERMINATED WITH A SHADE   TREE.       7. PLEASE CORRECT THE PARKING LOT STRIPING DETAIL TO   CONFORM TO THE CITY OF WPB REQUIREMENTS.       8. ENSURE THAT SPECIES SYMBOLS ARE CONSISTENT ACROSS   SPECIES.       9. MAKE SURE THAT ALL PLANT COUNTS ARE CONSISTENT   ACROSS THE TABLE, NUMBER OF SYMBOLS SHOWN, AND NUMBER   CALLED OUT ON THE PLANS.       10. PLEASE FOLLOW THE FPL RIGHT TREE RIGHT PLACE   GUIDELINES WITH RESPECT TO TREE SELECTION. THE COCONUT   PALMS AT THE NORTHEAST AND SOUTHEAST CORNERS OF THE LOT   ARE UNDER OVERHEAD POWERLINES, PLEASE REPLACE THEM WITH   LOWER TREES.       11. PLEASE CLARIFY WHERE ALL OF THE EXISTING PLANT   MATERIAL TO BE REUSED IS LOCATED. NOTE THAT ALL   MATERIAL TO BE REUSED MUST BE FLORIDA #1 OR GREATER.       12. THE PARALLEL PARKING SPACES SHOWN AT THE SOUTHEAST   CORNER ARE TOO SHORT; THE MINIMUM LENGTH IS 22 FEET.       PLEASE CONTACT KELLY FREEMAN, PLANNER, AT 561-822-1435   OR [email protected] WITH QUESTIONS. Review Stop Z ZONING Rev No 2 Status F Date 2007-03-27 Cont ID   Sent By kdfreema Date 2007-03-27 Time 10:06 Rev Time 0.00 Received By kdfreema Date 2007-03-27 Time 10:06 Sent To   Notes 2007-03-27 10:52:05 **FAILED**       1. ALL SURVEYS MUST BEAR AN ORIGINAL SIGNATURE AND   RAISED SEAL.       2. NO SITE PLAN WAS PROVIDED.       3. THE PROPOSED GENERATOR AS WELL AS ALL EXTERIOR   MECHANICAL EQUIPMENT MUST BE SHOWN ON BOTH THE SITE   PLAN AND LANDSCAPE PLAN.       4. PLEASE NOTE THAT ALTHOUGH THE ZONING CODE ALLOWS   GENERATORS TO BE PLACED AS CLOSE TO 1 FOOT FROM THE   PROPERTY LINE IN THIS ZONING DISTRICT, OTHER TRADES MAY   REQUIRE A GREATER SEPARATION DISTANCE.       PLEASE CONTACT KELLY FREEMAN, PLANNER, AT 561-822-1435   WITH ANY QUESTIONS. Review Stop Z ZONING Rev No 1 Status F Date 2009-07-27 Cont ID   Sent By kdfreema Date 2006-11-16 Time 11:10 Rev Time 0.00 Received By kdfreema Date 2006-11-16 Time 11:10 Sent To   Notes 2006-11-16 11:17:54 **FAILED**       COPIES OF YOUR SITE PLAN, LANDSCAPE PLAN, AND PROPERTY   SURVEY SHALL BE PROVIDED.       PLEASE CONTACT KELLY FREEMAN, PLANNER, AT (561)822-1435   WITH QUESTIONS.     Account Summary | Usage Policy | Privacy Policy Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved