Plan Review Details - Permit 06050515
Plan Review Stops For Permit 06050515
Review Stop B BUILDING (STRUCTURAL)
Rev No 6 Status P Date 2006-11-02 Cont ID  
Sent By alange Date 2006-11-02 Time 13:54 Rev Time 0.00
Received By alange Date 2006-11-02 Time 13:53 Sent To  
Notes
***NONE***
Review Stop B BUILDING (STRUCTURAL)
Rev No 5 Status F Date 2006-10-31 Cont ID  
Sent By alange Date 2006-10-30 Time 16:08 Rev Time 0.00
Received By alange Date 2006-10-30 Time 16:08 Sent To  
Notes
2006-10-31 09:03:42DENIED
  
 IMPACT FEES STILL DUE.I CALLED GWEN AT THE COUNTY
 IMPACT FEE OFFICE AND A IMPACT FEE REVIEW IS STILL
 NEEDED.
  
 BEFORE A PERMIT TO CONSTRUCT, MAY BE ISSUED, IMPACT
 FEES MUST BE PAID TO PALM BEACH COUNTY. THE ACTUAL
 PERMIT SET OF PLANS MUST BE STAMPED BY THAT OFFICE, AND
 A COPY OF THE PAID RECEIPT ATTACHED TO THE PERMIT
 APPLICATION. PLEASE CALL (561)233-5025 FOR MORE
 INFORMATION.
Review Stop B BUILDING (STRUCTURAL)
Rev No 4 Status F Date 2006-09-29 Cont ID  
Sent By alange Date 2006-09-29 Time 14:36 Rev Time 1.00
Received By alange Date 2006-09-29 Time 14:36 Sent To  
Notes
2006-09-29 00:00:00DENIED
 SAME COMMENTS, FOURTH REVIEW
  
 THE ONLY PRODUCT SUBMITTED SO FAR WITH
 STATE PRODUCT APPROVAL ATTACHED IS THE
 CLOPLAY OVERHEAD DOOR PRODUCT APPROVAL.
 ALL THE REST REQUIRED STATE PRODUCT
 APPROVALS TO BE ATTACHED.
  
 5.ALL PRODUCT APPROVALS SUBMITTED WITH
 QUALITY ASSURANCE SHALL HAVE THE
 FOLLOWING STATE APPROVAL ATTACHED.
  
 PRODUCT APPROVALS SUBMITTED WITH
 PERMIT APPLICATION AFTER OCTOBER 1, 2003
 ARE REQUIRED TO COMPLY WITH THE FLORIDA
 PRODUCT APPROVAL SYSTEM. FOR INFORMATION
 PLEASE SEE THE STATE WEBSITE AT
 WWW.FLORIDABUILDING.ORG. PRODUCTS WITH
 STATEWIDE APPROVAL ARE REQUIRED TO BE
 SUBMITTED WITH A STATE PRODUCT APPROVAL
 SHEETS THAT LISTS THE PRODUCT IDENTITY
 NUMBER FROM THE STATE. IF THE PRODUCT
 DOES NOT HAVE STATEWIDE APPROVAL, SUBMIT
 AN APPLICATION FOR LOCAL PRODUCT
 APPROVAL OR SITE SPECIFIC FORM PER RULE
 9B-72. SEE ATTACHMENT.
 WWW.FLORIDABUILDING.ORG
  
 NEW:TRUSS DRAWINGS SHALL BE REVIEWED
 AND APPROVED PRIOR TO INSTALLATION, NOT
 PERMITTING.ONLY ONE SET SUBMITTED.
 SUBMIT TWO ORIGONAL SETS PRIOR TO
 INSTALLATION.
  
  
 WHEN RESUBMITTING PLANS PLEASE INDICATE
 THE REVISION & REMOVE & REPLACE ANY
 PAGES AS NECESSARY. SUBMIT ONE COPY OF
 OLD PAGES FOR REFERENCE. A TRANSMITTAL
 LETTER LISTING THE ORIGINAL REVIEW
 COMMENT NUMBER, WITH A DESCRIPTION OF
 THE REVISION MADE, IDENTIFYING THE SHEET
 OR SPECIFICATION PAGE WHERE THE CHANGES
 CAN BE FOUND WILL HELP TO EXPEDITE YOUR
 PERMIT. THANK YOU FOR YOUR ANTICIPATED
 COOPERATION.
  
 ART LANGE
 CONSTRUCTION SERVICES DEPARTMENT
 BUILDING PLANS EXAMINER
 561-805-6672
Review Stop B BUILDING (STRUCTURAL)
Rev No 3 Status F Date 2006-09-05 Cont ID  
Sent By alange Date 2006-09-05 Time 07:59 Rev Time 1.25
Received By alange Date 2006-09-05 Time 07:59 Sent To  
Notes
2006-09-05 00:00:00DENIED
  
  
 1.713.13(2) F.S.THE NOTICE OF
 COMMENCEMENT MUST BE RE-RECORDED BECAUSE
 THE DESCRIBED IMPROVEMENT OR
 CONSTRUCTION DID NOT COMMENCE WITHIN 90
 DAYS OF RECORDING.
  
 2.BASED ON ICC BUILDING VALUATION DATA
 THE PERMIT VALUE HAS BEEN REVISED TO
 $134,614.00.ADDITIONAL PERMIT FEES ARE
 DUE.
  
 5.ALL PRODUCT APPROVALS SUBMITTED WITH
 QUALITY ASSURANCE SHALL HAVE THE
 FOLLOWING STATE APPROVAL ATTACHED.
  
 PRODUCT APPROVALS SUBMITTED WITH
 PERMIT APPLICATION AFTER OCTOBER 1, 2003
 ARE REQUIRED TO COMPLY WITH THE FLORIDA
 PRODUCT APPROVAL SYSTEM. FOR INFORMATION
 PLEASE SEE THE STATE WEBSITE AT
 WWW.FLORIDABUILDING.ORG. PRODUCTS WITH
 STATEWIDE APPROVAL ARE REQUIRED TO BE
 SUBMITTED WITH A STATE PRODUCT APPROVAL
 SHEETS THAT LISTS THE PRODUCT IDENTITY
 NUMBER FROM THE STATE. IF THE PRODUCT
 DOES NOT HAVE STATEWIDE APPROVAL, SUBMIT
 AN APPLICATION FOR LOCAL PRODUCT
 APPROVAL OR SITE SPECIFIC FORM PER RULE
 9B-72. SEE ATTACHMENT.
 WWW.FLORIDABUILDING.ORG
  
 7.SUBMIT TWO ORIGONAL SIGNED AND
 SEALED SURVEYS.
  
 9.FOOTING DEPTH SHALL BE A MINIMUM OF
 12" BELOW GRADE.R-403.1.4CHECK THE
 DETAIL SHOWN.
  
  
 WHEN RESUBMITTING PLANS PLEASE INDICATE
 THE REVISION & REMOVE & REPLACE ANY
 PAGES AS NECESSARY. SUBMIT ONE COPY OF
 OLD PAGES FOR REFERENCE. A TRANSMITTAL
 LETTER LISTING THE ORIGINAL REVIEW
 COMMENT NUMBER, WITH A DESCRIPTION OF
 THE REVISION MADE, IDENTIFYING THE SHEET
 OR SPECIFICATION PAGE WHERE THE CHANGES
 CAN BE FOUND WILL HELP TO EXPEDITE YOUR
 PERMIT. THANK YOU FOR YOUR ANTICIPATED
 COOPERATION.
  
 ART LANGE
 CONSTRUCTION SERVICES DEPARTMENT
 BUILDING PLANS EXAMINER
 561-805-6672
Review Stop B BUILDING (STRUCTURAL)
Rev No 2 Status F Date 2006-08-16 Cont ID  
Sent By alange Date 2006-08-16 Time 11:28 Rev Time 1.50
Received By alange Date 2006-08-16 Time 11:28 Sent To  
Notes
2006-08-16 00:00:00DENIED
  
  
 1.713.13(2) F.S.THE NOTICE OF
 COMMENCEMENT MUST BE RE-RECORDED BECAUSE
 THE DESCRIBED IMPROVEMENT OR
 CONSTRUCTION DID NOT COMMENCE WITHIN 90
 DAYS OF RECORDING.
  
 2.BASED ON ICC BUILDING VALUATION DATA
 THE PERMIT VALUE HAS BEEN REVISED TO
 $134,614.00.ADDITIONAL PERMIT FEES ARE
 DUE.
  
 5.ALL PRODUCT APPROVALS SUBMITTED WITH
 QUALITY ASSURANCE SHALL HAVE THE
 FOLLOWING STATE APPROVAL ATTACHED.
  
 PRODUCT APPROVALS SUBMITTED WITH
 PERMIT APPLICATION AFTER OCTOBER 1, 2003
 ARE REQUIRED TO COMPLY WITH THE FLORIDA
 PRODUCT APPROVAL SYSTEM. FOR INFORMATION
 PLEASE SEE THE STATE WEBSITE AT
 WWW.FLORIDABUILDING.ORG. PRODUCTS WITH
 STATEWIDE APPROVAL ARE REQUIRED TO BE
 SUBMITTED WITH A STATE PRODUCT APPROVAL
 SHEETS THAT LISTS THE PRODUCT IDENTITY
 NUMBER FROM THE STATE. IF THE PRODUCT
 DOES NOT HAVE STATEWIDE APPROVAL, SUBMIT
 AN APPLICATION FOR LOCAL PRODUCT
 APPROVAL OR SITE SPECIFIC FORM PER RULE
 9B-72. SEE ATTACHMENT.
 WWW.FLORIDABUILDING.ORG
  
 6.SUBMIT TWO SETS OF TRUSS DRAWINGS
 FOR REVIEWPRIOR TO INSTALLATION PER
 2004 FBC R-802.10.1
  
 7.SUBMIT TWO ORIGONAL SIGNED AND
 SEALED SURVEYS.
  
 9.FOOTING DEPTH SHALL BE A MINIMUM OF
 12" BELOW GRADE.R-403.1.4
  
  
 WHEN RESUBMITTING PLANS PLEASE INDICATE
 THE REVISION & REMOVE & REPLACE ANY
 PAGES AS NECESSARY. SUBMIT ONE COPY OF
 OLD PAGES FOR REFERENCE. A TRANSMITTAL
 LETTER LISTING THE ORIGINAL REVIEW
 COMMENT NUMBER, WITH A DESCRIPTION OF
 THE REVISION MADE, IDENTIFYING THE SHEET
 OR SPECIFICATION PAGE WHERE THE CHANGES
 CAN BE FOUND WILL HELP TO EXPEDITE YOUR
 PERMIT. THANK YOU FOR YOUR ANTICIPATED
 COOPERATION.
  
 ART LANGE
 CONSTRUCTION SERVICES DEPARTMENT
 BUILDING PLANS EXAMINER
 561-805-6672
Review Stop B BUILDING (STRUCTURAL)
Rev No 1 Status F Date 2006-05-23 Cont ID  
Sent By alange Date 2006-05-23 Time 14:05 Rev Time 1.75
Received By alange Date 2006-05-23 Time 13:41 Sent To  
Notes
2006-05-23 00:00:00DENIED
  
  
 1.BEFORE A PERMIT TO CONSTRUCT, MAY BE
 ISSUED, IMPACT FEES MUST BE PAID TO PALM
 BEACH COUNTY. THE ACTUAL PERMIT
 SET OF PLANS MUST BE STAMPED BY THAT
 OFFICE, AND A COPY OF THE PAID RECEIPT
 ATTACHED TO THE PERMIT APPLICATION.
 PLEASE CALL (561)233-5025 FOR MORE
 INFORMATION.
  
 2.BASED ON ICC BUILDING VALUATION DATA
 THE PERMIT VALUE HAS BEEN REVISED TO
 $134,614.00.ADDITIONAL PERMIT FEES ARE
 DUE.
  
 3.SIGN OWNER/AGENT ON ENERGY CALCS PER
 2004 FBC.
  
 4.PRODUCT APPROVALS REQUIRED FOR
 ROOFING, STRAPS AND TIE-DOWNS AND GARAGE
 OVERHEAD DOOR.
  
 5.ALL PRODUCT APPROVALS SUBMITTED WITH
 QUALITY ASSURANCE SHALL HAVE THE
 FOLLOWING STATE APPROVAL ATTACHED.
  
 PRODUCT APPROVALS SUBMITTED WITH
 PERMIT APPLICATION AFTER OCTOBER 1, 2003
 ARE REQUIRED TO COMPLY WITH THE FLORIDA
 PRODUCT APPROVAL SYSTEM. FOR INFORMATION
 PLEASE SEE THE STATE WEBSITE AT
 WWW.FLORIDABUILDING.ORG. PRODUCTS WITH
 STATEWIDE APPROVAL ARE REQUIRED TO BE
 SUBMITTED WITH A STATE PRODUCT APPROVAL
 SHEETS THAT LISTS THE PRODUCT IDENTITY
 NUMBER FROM THE STATE. IF THE PRODUCT
 DOES NOT HAVE STATEWIDE APPROVAL, SUBMIT
 AN APPLICATION FOR LOCAL PRODUCT
 APPROVAL OR SITE SPECIFIC FORM PER RULE
 9B-72. SEE ATTACHMENT.
 WWW.FLORIDABUILDING.ORG
  
 6.SUBMIT TWO SETS OF TRUSS DRAWINGS
 FOR REVIEW PER 2004 FBC R-802.10.1
  
 7.SUBMIT TWO ORIGONAL SIGNED AND
 SEALED SURVEYS.
  
 8.WINDOW AT TUB AREA SHALL HAVE SAFTEY
 GLAZING. R-308.4
  
 9.FOOTING DEPTH SHALL BE A MINIMUM OF
 12" BELOW GRADE.R-403.1.4
  
  
 WHEN RESUBMITTING PLANS PLEASE INDICATE
 THE REVISION & REMOVE & REPLACE ANY
 PAGES AS NECESSARY. SUBMIT ONE COPY OF
 OLD PAGES FOR REFERENCE. A TRANSMITTAL
 LETTER LISTING THE ORIGINAL REVIEW
 COMMENT NUMBER, WITH A DESCRIPTION OF
 THE REVISION MADE, IDENTIFYING THE SHEET
 OR SPECIFICATION PAGE WHERE THE CHANGES
 CAN BE FOUND WILL HELP TO EXPEDITE YOUR
 PERMIT. THANK YOU FOR YOUR ANTICIPATED
 COOPERATION.
  
 ART LANGE
 CONSTRUCTION SERVICES DEPARTMENT
 BUILDING PLANS EXAMINER
 561-805-6672
  
Review Stop E ELECTRICAL
Rev No 2 Status P Date 2006-08-08 Cont ID  
Sent By btrobaug Date 2006-08-08 Time 11:17 Rev Time 0.50
Received By btrobaug Date 2006-08-08 Time 10:49 Sent To P
Notes
***NONE***
Review Stop E ELECTRICAL
Rev No 1 Status F Date 2006-05-17 Cont ID  
Sent By btrobaug Date 2006-05-17 Time 15:40 Rev Time 1.00
Received By btrobaug Date 2006-05-17 Time 14:17 Sent To M
Notes
2006-05-17 00:00:00 
 DENIED
  
 PLEASE MAKE THE FOLLOWING CORRECTIONS
 FORCODE COMPLIANCE AND RESUBMIT FOR
 REVIEW.
  
 1} THE 1/0 FEEDER TO THE "200 AMP ELEC.
 PANEL MLO SN" IS RATED FOF 175 AMPS PER
 310.15(B)(6). INDICATE THE OCP IN THE
 METER/MAIN COMBO FOR THIS FEEDER. 200
 AMP IS TOO LARGE.
  
 2} INDICATE THE AIC RATING AS CALCULATED
 FOR THE FAULT CURRENT FROM THE
 TRANSFORMER TO THE EQUIPMENT PER 110.9 &
 10.
  
 3} PLEASE SEE THE FOLLOWING CIRCUITS IN
 THE PANEL ARE INCORRECT:
  
 A) 8&9- SMALL APPLIANCE@ 1500 EACH PER
 210.11(C)(3)=300VA.
  
 B) 12&14-#12 WIRE ON A 30 AMP OCP,
 310.16.
  
 C) 17&19-AHU @ 10K DOES NOT CORRELATE
 WITH SHEET #9 INDICATING 5K.
  
 4} PLACE THE SERVICE EQUIPMENT AT THE
 PROPOSED LOCATION ON THE PLAN.
  
 5} PLEASE SEE A RECEPTACLE FOR A/C
 EQUIPMENT PER 210.63 IS REQUIRED FOR THE
 COMPRESSOR.
  
 6} THE ENGINEERS CERTIFICATE OF
 AUTHORIZATION NUMBER MUST BE INCLUDED IN
 THE TITLE BLOCK PER 61G15-002 (2), FAC.
 ALL SHEETS .
  
 IF THERE ARE ANY QUESTIONS PLEASE CALL.
  
 BILL TROBAUGH
 ELECTRICAL PLAN REVIEW
 561/805-6718
 [email protected]
 FAX/:561/659-8026
  
  
  
Review Stop I INCOMING/PROCESSING
Rev No 6 Status N Date 2006-10-30 Cont ID  
Sent By adarroug Date 2006-10-30 Time 11:10 Rev Time 0.00
Received By adarroug Date 2006-10-30 Time 11:10 Sent To B
Notes
2006-10-30 11:11:00TO "ALANGE" DESK/SUBMITTAL
Review Stop I INCOMING/PROCESSING
Rev No 5 Status N Date 2006-09-21 Cont ID  
Sent By adarroug Date 2006-09-21 Time 09:43 Rev Time 0.00
Received By adarroug Date 2006-09-21 Time 09:43 Sent To B
Notes
2006-09-21 00:00:00TO "ALANGE" DESK/RESUB
Review Stop I INCOMING/PROCESSING
Rev No 4 Status N Date 2006-08-24 Cont ID  
Sent By adarroug Date 2006-08-24 Time 11:45 Rev Time 0.00
Received By adarroug Date 2006-08-24 Time 11:45 Sent To B
Notes
2006-08-24 00:00:00TO "ALANGE" DESK/RESUB
Review Stop I INCOMING/PROCESSING
Rev No 3 Status N Date 2006-08-07 Cont ID  
Sent By adarroug Date 2006-08-07 Time 14:32 Rev Time 0.00
Received By adarroug Date 2006-08-07 Time 14:32 Sent To E
Notes
2006-08-07 00:00:00TO "BTROBAUG" DESK/RESUB
Review Stop I INCOMING/PROCESSING
Rev No 2 Status N Date 2006-08-01 Cont ID  
Sent By adarroug Date 2006-08-01 Time 13:22 Rev Time 0.00
Received By adarroug Date 2006-08-01 Time 13:21 Sent To Z
Notes
2006-08-01 00:00:00TO "Z" BOX/RESUB
Review Stop I INCOMING/PROCESSING
Rev No 1 Status N Date 2006-05-23 Cont ID  
Sent By alange Date 2006-05-23 Time 13:41 Rev Time 0.00
Received By alange Date 2006-05-15 Time 14:56 Sent To  
Notes
2006-05-15 00:00:00TO "SFR" "Z"
Review Stop M MECHANICAL (A/C)
Rev No 2 Status P Date 2006-08-14 Cont ID  
Sent By tgordon Date 2006-08-14 Time 14:50 Rev Time 0.30
Received By tgordon Date 2006-08-14 Time 14:49 Sent To B
Notes
***NONE***
Review Stop M MECHANICAL (A/C)
Rev No 1 Status F Date 2006-05-22 Cont ID  
Sent By tgordon Date 2006-05-22 Time 11:19 Rev Time 0.45
Received By tgordon Date 2006-05-22 Time 11:19 Sent To B
Notes
2006-05-22 00:00:00*** DENIED ***
 1) ENERGY CAL'S. NEED TO BE SIGNED BY
 OWNER/AGENT.
  
 2) MECHANICAL PLANS ARE CALLING FOR A %
 KW HEATER, THE ELECTRICAL PLANS AND
 ENERGY CAL'S. ARE CALLING FOR 10 KW
 HEATER, PLEASE CORRECT.
  
 3) PLEASE SEE ELECTRICAL REVIEW NOTE #6
 (C.A. #).
  
 4) MASTER BEDROOM RETURN AIR TRANSFER
 DUCT IS TO SMALL, SEE NOTE #5 (C)EXCEPT.
  
 5)BALANCED RETURN AIR.
 THIS MAY BE ACHIEVED BY.
 (A)TRANSFER DUCTS MAY ACHIEVE THIS BY
 INCREASING THE RETURN TRANSFER ONE AND
 ONE HALF TIMES THE CROSS SECTIONAL AREA
 (SQUARE INCHES) OF THE SUPPLY DUCT
 ENTERING THE ROOM OR SPACE IT'S SERVING
 AND THE DOOR HAVING AT LEAST AN
 UNRESTRICTED 1 INCHUNDERCUT TO ACHIEVE
 PROPER RETURN AIR BALANCE.
 (B)TRANSFER GRILLES SHALL USE 50
 SQUARE INCHES (OF GRILLE AREA) TO 100
 CFM (OF SUPPLY AIR) FOR SIZING
 THROUGH-THE-WALL TRANSFER GRILLES AND
 USING AN UNRESTRICTED 1-INCH
 UNDERCUTTING OF DOORS TO ACHIEVE PROPER
 RETURN AIR BALANCE
 (C)HABITABLE ROOMS ONLY SHALL BE
 REQUIRED TO MEET THESE REQUIREMENTS FOR
 PROPER BALANCED RETURN AIR EXCLUDING
 BATHROOMS, CLOSETS, STORAGE ROOMS AND
 LAUNDRY ROOMS, EXCEPT THAT ALL SUPPLY
 AIR INTO THE MASTER SUITE SHALL BE
 INCLUDED. PER 2004 FBC/R M1602.4 .
  
 MECHANICAL PLAN REVIEW BY;
 TOM GORDON (561) 805-6729.
Review Stop P PLUMBING
Rev No 2 Status P Date 2006-08-14 Cont ID  
Sent By mperson Date 2006-08-14 Time 08:49 Rev Time 0.33
Received By mperson Date 2006-08-14 Time 08:49 Sent To M
Notes
***NONE***
Review Stop P PLUMBING
Rev No 1 Status F Date 2006-05-22 Cont ID  
Sent By mperson Date 2006-05-22 Time 08:29 Rev Time 1.00
Received By mperson Date 2006-05-22 Time 08:29 Sent To M
Notes
2006-05-22 00:00:00******DENIED******
 REFERENCE: FBC-2004 PLUMBING
 FLORIDA ADMINISTRATIVE CODE
  
 THE FOLLOWING INFORMATION IS REQUIRED
 FOR PLAN REVIEW FOR A PLUMBING PERMIT:
  
 1. ON SHEET 8 OF 9 PLEASE MAKE THE
 CORRECTIONS INDICATED ON CLEANOUTS FOR
 RESUBMITTAL.
 (A) 708.3.4 BASE OF STACK. A CLEANOUT
 SHALL BE PROVIDED AT THE BASE OF EACH
 WASTE OR SOIL STACK
 (B) 708.3.5 BUILDING DRAIN AND BUILDING
 SEWER JUNCTION. THERE SHALL BE A
 CLEANOUT NEAR THE JUNCTION OF THE
 BUILDING DRAIN AND THE BUILDING SEWER.
 (C) 708.7 MINIMUM SIZE. CLEANOUTS SHALL
 BE THE SAME NOMINAL SIZE AS THE PIPE
 THEY SERVE UP TO 4 INCHES (102MM)
 (D) 708.9 ACCESS. ACCESS SHALL BE
 PROVIDED TO ALL CLEANOUTS. PLEASE NOTE
 THE LOCATION OF THE CLEANOUT FOR THE
 WASHING MACHINE.
 2. ON SHEET 8 OF 9 PLEASE MAKE THE
 CORRECTIONS INDICATED ON WASHING
 MACHINES FOR RESUBMITTAL.
 (B) 802.4 STANDPIPES.STANDPIPES SHALL BE
 INDIVIDUALLY TRAPPED. STANDPIPES SHALL
 EXTEND A MINIMUM OF 18 INCHES (457MM)
 AND A MAXIMUM OF 42 INCHES (1066MM)
 ABOVE THE TRAP WEIR. ACCESS SHALL BE
 PROVIDED TO ALL STANDPIPES AND DRAINS
 FOR RODDING. PLEASE INDICATE THIS STAND-
 PIPE ON THE RESUBMITTED DRAWINGS.
 3. ON SHEET 8 OF 9 PLEASE CHANGE STUDOR
 VENT TO AIR ADMITTANCE VALVE FOR
 RESUBMITTAL PER SECTION 917
 4. ON SHEET 8 OF 9 PLEASE INDICATE ON
 THE WATER PIPING ISOMETRIC THE WATER-
 HAMMER ARRESTORS REQUIRED FOR QUICK-
 CLOSING VALVES PER SECTION 604.9 FOR
 RESUBMITTAL.
 5. ON SHEET 8 OF 9 PLEASE INDICATE ON
 THE WATER PIPING ISOMETRIC THE FULL-
 OPEN VALVE REQUIRED ON THE WATER
 DISTRIBUTION SUPPLY PIPE AT THE ENTRANCE
 INTO THE STRUCTURE PER SECTION 606.1 FOR
 RESUBMITTAL.
 6. PLEASE SEE ELECTRICAL NOTE #6
  
 END OF COMMENTS:
  
 REVIEW BY MIKE PERSON
 (561) 805-6730
 FAX (561) 805-6731
 E-MAIL [email protected]
 UNDER SUPERVISION OF K.STEVENS
 (561) 805-6721
  
  
Review Stop Z ZONING
Rev No 2 Status P Date 2006-08-05 Cont ID  
Sent By mmclean Date 2006-08-05 Time 08:27 Rev Time 0.00
Received By mmclean Date 2006-08-05 Time 08:27 Sent To I
Notes
***NONE***
Review Stop Z ZONING
Rev No 1 Status F Date 2006-05-16 Cont ID  
Sent By mmclean Date 2006-05-16 Time 15:53 Rev Time 0.00
Received By mmclean Date 2006-05-16 Time 15:53 Sent To E
Notes
2006-05-16 00:00:00DENIED,
 1. THE PROPOSED DRIVEWAY HAS TOO MUCH
 CONCRETE WITHIN THE FIRST 25FT FRONT
 SETBACK.
 2. NEED TO REDUCE THE PROPOSED DRIVEWAY
 TO MEET THE ALLOWED 305.25SQ FT WITHIN
 THE FIRST 25FT FRONT SETBACK. (DRIVEWAY
 CAN ONLY BE 12FT WIDE).
  
 NOTE: MUST MAINTAIN 1000SQ FT OR 75% OF
 LANDSCAPE, WHICHEVER IS LESS WITHIN THE
 FIRST 25FT FRONT SETBACK.
  
 MICHELLE MCLEAN
 ZONING TECHNICIAN
 805-6720
  


Account Summary | Usage Policy | Privacy Policy
Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved