City of West Palm Beach eGovPlus

Plan Review Details - Permit 06020892

Plan Review Stops For Permit 06020892

Notes

2006-04-27 00:00:00

	TOM GORDON IS WALKING PLANS THROUGH SEND
	TO ELEC

Notes

2006-04-25 00:00:00

	DENIED

	1) ONLY 2 PRODUCT APPROVALS WERE
	APPROVED BY DESIGNER OF RECORD. PLEASE
	STAMP ALL COPIES OF ALL PRODUCTS

	2) PRODUCT APPROVALS WERE SUBMITTED FOR
	STORM PANELS. PLEASE SPECIFY WHERE THEY
	ARE TO BE USED AS THE WINDOWS DO NOT
	REQUIRE THEM BECAUSE PRODUCT APPROVALS
	ARE FOR IMPACT WINDOWS. PLEASE CLARIFY

	3) WE REQUIRE 2 COPIES OF ALL SUBMITTALS
	THIS INCLUDES ENERGY CALC'S AND MANUAL
	J,S (SEE MECHANICAL NOTES)

	BLDG PLAN REVIEW
	ADRIAN MORSE
	561-805-6716

Notes

2006-03-28 00:00:00

	DENIED

	1) BEFORE A PERMIT TO CONSTRUCT, MAY
	BE ISSUED, IMPACT FEES MUST BE PAID TO
	PALM BEACH COUNTY. THE ACTUAL PERMIT
	SETS OF PLANS MUST BE STAMPED BY THAT
	OFFICE, AND A COPY OF THE PAID RECEIPT
	ATTACHED TO THE PERMIT APPLICATION.
	PLEASE CALL (561)233-5025 FOR MORE

	2) THE CLAIMED VALUATION ON THE PERMIT
	APPLICATION IS LOW. FOR PERMITTING
	PURPOSES, VALUATION OF BUILDINGS AND
	SYSTEMS SHALL BE THE TOTAL REPLACEMENT
	COST EXCLUDING LAND VALUE. OUR VALUATION
	REFERENCE IS ICC (BVD), MARSHALL-SWIFT
	AND MEANS COST ANALYSIS SERVICES PER
	108.3 FBC* THE VALUE HAS BEEN ADJUSTED
	AND FEE ARE DUE

	3) THE STATE OF FLORIDA REQUIRES
	COLLECTION OF A RADON SURCHARGE ON ALL
	NEW CONSTRUCTION COMPUTED ON UNDER ROOF
	FLOOR SPACE

	4) SUBMIT ENGINEERED TRUSS DRAWINGS THAT
	COMPLY WITH R802.10.1 FBC WITH PERMIT
	APPLICATION OR BEFORE INSTALLATION

	5) THOSE PRODUCTS WHICH ARE REGULATED BY
	DCA RULE 9B-72 SHALL BE REVIEWED AND
	APPROVED IN WRITING BY THE DESIGNER OF
	RECORD PRIOR TO SUBMITTAL FOR
	JURISDICTIONAL APPROVAL PER 106.3.3 FBC*

	6) AMEND DRAWINGS TO COMPLY WITH THE
	DESIGN PARAMETERS FROM 1609 AND
	ASCE 7-02

	7) A RECORDED COPY OF THE NOTICE OF
	COMMENCEMENT IS REQUIRED PRIOR TO
	A PERMIT BEING ISSUED



	8) PRODUCT APPROVAL NOA'S FOR SHINGLES
	ARE OUTDATED PLEASE SUBMIT NEW NOA'S

	* WEST PALM BEACH ADMINISTRATIVE AMMEND.


	BLDG PLAN REVIEW
	ADRIAN MORSE
	561-805-6716

Notes

2006-04-25 00:00:00
	ENGINEER MUST COMPLY WITH 16G15-23.002
	FAC.

	THE ELECTRICAL PLAN IS O.K. PLEASE
	RESUBMIT AFTER ENGINEER CORRECTS.

	BILL TROBAUGH
	ELECTRICAL PLAN REVIEW
	561/805-6718
	[email protected]
	FAX/:561/659-8026

Notes

2006-03-13 00:00:00
	PLEASE MAKE THE FOLLOWING CORRECTIONS
	FOR CODE COMPLIANCE AND RESUBMIT FOR
	REVIEW.

	1} PLEASE INDICATE THE AIC RATING OF THE
	EQUIPMENT PER 110.9 & 110.10.

	2} THE CURRENT NEC CYCLE IS 2002. SEE
	NOTE #1.

	3} BEDROOMS 1,3,4 AND LIVING ROOM NEED
	RECEPTACLES ADDED TO COMPLY WITH
	210.52(A)(1)&(2). SEE REVIEWED SET OF
	PLANS.

	4} THE RECEPTACLE ON THE KITCHEN ISLAND
	MUST COMPLY WITH 210.8(A)(6)

	5} A RECEPTACLE MUST BE LOCATED OUTSIDE
	AT THE FRONT OF THE RESIDENCE TO COMPLY
	WITH 210.52(E).

	6} THE OCP FOR THE AHU @ 80 (CIRCUIT
	1/3), IS TOO LARGE FOR THE #6 CONDUCTOR,
	SEE 210.16.

	IF THERE ARE ANY QUESTIONS PLEASE CALL.

	BILL TROBAUGH
	ELECTRICAL PLAN REVIEW
	561/805-6718
	[email protected]
	FAX/:561/659-8026

Notes

2006-04-17 00:00:00

TO "BTROBAUG" DESK/RESUB

Notes

2006-03-09 00:00:00

TO "E" BOX

Notes

2006-02-22 00:00:00

TO "Z" BOX

Notes

2006-04-27 00:00:00	MECHANICAL PLANS REMOVED AND WILL APPLY
	FOR MECH. LATER.

Notes

2006-04-25 00:00:00	* DENIED *
	1) ENGINEER'S NAME, ADDRESS, AND LICENSE
	NUMBER MUST BE LEGIBLY INDICATED ON ALL
	PLANS THAT HAVE HIS SEAL ON THEM, PER
	FAC 61G15-23.002 .

	2) RETURN AIR DUCTS TO BEDROOMS DO NOT
	RETURN TO TRUNK LINE OR A/C UNIT PLEASE
	CORRECT.

	3) RETURN AIR TRUNK LINE TO AIR HANDLER
	UNIT IS NOT SIZED.

	4) MANUAL J CAL'S. ARE SHOWING 110
	CFM'S. TO EACH AND EVERY ROOM REGARDLESS
	OF ROOM SIZE PLEASE CORRECT.

	5) MANUAL J CAL'S. DO NOT SHOW NAME OF
	ROOMS AND NEED TO.

	6) MECHANICAL PLANS CFM'S. TO EACH ROOM
	AND MANUAL J CAL'S. CFM'S. TO EACH ROOM
	DO NOT MATCH PLEASE CORRECT.

	MECHANICAL PLAN REVIEW BY;
	TOM GORDON (561) 805-6729.

Notes

2006-03-13 00:00:00	* DENIED *
	1) NEED TO SUBMIT A NEW MANUAL J (LONG
	FORM) FOR THE ENTIRE HOUSE, SHOWING
	CFM'S FOR EACH ROOM.

	2) NEED TO SHOW ALL DUCT SIZES, GRILL
	SIZES, AND CFM'S ON MECHANICAL PLANS.

	3) PLEASE SHOW CLOTHS DRYER VENT ON
	MECHANICAL PLANS.

	4) PLEASE PROVIDE RETURN AIR TO ALL
	BEDROOMS SEE NOTE #5.

	5)BALANCED RETURN AIR.
	THIS MAY BE ACHIEVED BY.
	(A)TRANSFER DUCTS MAY ACHIEVE THIS BY
	INCREASING THE RETURN TRANSFER ONE AND
	ONE HALF TIMES THE CROSS SECTIONAL AREA
	(SQUARE INCHES) OF THE SUPPLY DUCT
	ENTERING THE ROOM OR SPACE IT'S SERVING
	AND THE DOOR HAVING AT LEAST AN
	UNRESTRICTED 1 INCHUNDERCUT TO ACHIEVE
	PROPER RETURN AIR BALANCE.
	(B)TRANSFER GRILLES SHALL USE 50
	SQUARE INCHES (OF GRILLE AREA) TO 100
	CFM (OF SUPPLY AIR) FOR SIZING
	THROUGH-THE-WALL TRANSFER GRILLES AND
	USING AN UNRESTRICTED 1-INCH
	UNDERCUTTING OF DOORS TO ACHIEVE PROPER
	RETURN AIR BALANCE
	(C)HABITABLE ROOMS ONLY SHALL BE
	REQUIRED TO MEET THESE REQUIREMENTS FOR
	PROPER BALANCED RETURN AIR EXCLUDING
	BATHROOMS, CLOSETS, STORAGE ROOMS AND
	LAUNDRY ROOMS, EXCEPT THAT ALL SUPPLY
	AIR INTO THE MASTER SUITE SHALL BE
	INCLUDED. PER 2004 FBC/R M1602.4 .

	MECHANICAL PLAN REVIEW BY;
	TOM GORDON (561) 805-6729.

Notes

***NONE***

Notes

***NONE***