Plan Review Details - Permit 06010103
Plan Review Stops For Permit 06010103
Review Stop B BUILDING (STRUCTURAL)
Rev No 3 Status P Date 2006-03-22 Cont ID  
Sent By mjacobs Date 2006-03-22 Time 11:05 Rev Time 0.00
Received By mjacobs Date 2006-03-21 Time 15:34 Sent To Z
Notes
***NONE***
Review Stop B BUILDING (STRUCTURAL)
Rev No 2 Status F Date 2006-03-17 Cont ID  
Sent By mjacobs Date 2006-03-17 Time 14:44 Rev Time 0.00
Received By mjacobs Date 2006-03-17 Time 07:04 Sent To PC
Notes
2006-03-17 00:00:001) NOTE: THE PRODUCT APPROVAL FOR THE
 GARAGE DOOR IS EXPIRED. PLEASE SUBMIT AN
 APPROVED AND UPDATED PRODUCT FOR REVIEW.
 SEE MIAMI DADE NOA #01-0323.05 EXIRED
 2/14/06.
 THOSE PRODUCT APPROVALS WHICH ARE
 REGULATED BY DCA RULE 9B-72 SHALL BE
 REVIEWED AND APPROVED IN WRITING BY THE
 DESIGNER OF RECORD PRIOR TO SUBMITTAL
 FOR JURISDICTIONAL APPROVAL.WPB
 AMMENDMENT TO FBC 106.3.3
  
 2) INDICATE ON THE WHERE EACH FOOTING
 DETAIL IS USED ON SHEET A1. DETAILS
 F1,F2 AND F3 SHOULD BE SHOWN ON THE
 FOUNDATION PLANS.
  
 3) THE CONNECTION DETAIL SHOWS TAPCONS
 SCREWS. WHY WILL TAPCONS BE USED TO
 ATTATCH THE RAILINGAS TO THE WOOD FRAME
 INSTEAD OF WOOD SCREWS? PLEASE CLARIFY.
  
 4) STATE HOW THE ROOF TILES WILL BE
 ATTATCH TO THE DECK. WILL THE TILES BE
 NAILED,SCREWED OR FOAM TO THE DECK?
  
 5) THE F1 FOOTING DETAIL ON SHEET A1
 INDICATES A CC66.THIS IS A WOOD TO WOOD
 COLUM CAP NOT A WOOD TO CONCRETE. SEE
 SIMPSON STRONG-TIE CATALOG. SHOW THE
 PROPER CONNECTION FOR THIS DETAIL.
  
 6) THE ABU66 SHOULD BE USED ON CONCRETE
 SO, IF THIS ANCHR IS USED THE BASE SHALL
 BE CONCRETE. SEE SHEET A6.
  
 MYRON JACOBS
 BUILDING PLAN REVIEWER
 805-6726
  
Review Stop B BUILDING (STRUCTURAL)
Rev No 1 Status F Date 2006-02-21 Cont ID  
Sent By mjacobs Date 2006-02-21 Time 09:58 Rev Time 2.50
Received By mjacobs Date 2006-02-21 Time 07:10 Sent To PC
Notes
2006-02-10 00:00:001) 110.2* W. P. B. ADMINISTRATIVE CODE,
 INFORMATION THAT IS REQUIRED FOR RECORD
 KEEPING & FOR CERTIFICATE OF OCCUPANCY:
 A) THE EDITION OFTHE CODE UNDER WHICH
 THE PERMIT WAS ISSUED.
 B) THE USE AND OCCUPANCY, IN ACCORDANCE
 WITH THE PROVISIONS OF CHAPTER 3.
 C) THE TYPE OF CONSTRUCTION AS DEFINED
 IN CHAPTER 6, TABLE 601.
 D) THE DESIGN OCCUPANT LOAD, SEE 1004.
 E) IF AN AUTOMATIC SPRINKLER SYSTEM IS
 PROVIDED, WHETHER THE SPRINKLER SYSTEM
 IS REQUIRED.
 F) ANY SPECIAL STIPULATIONS & CONDITIONS
 OF THE BUILDING PERMIT.
  
 2) 109.3.10* IMPACT OF CONSTRUCTION. ALL
 CONSTRUCTION ACTIVITY REGULATED BY THIS
 CODE SHALL BE PERMORMED IN A MANNER SO
 AS NOT TO ADVERSLY IMPACT THE CONDITION
 OF ADJACENT PROPERTY, UNLESS SUCH
 ACTIVITY IS PERMITTED TO AFFECT SAID
 PROPERTY PURSUANT TO A CONSENT BY THE
 APPLICABLE PROPERTY OWNER, UNDER TERMS &
 CONDITIONS AGREEABLE TO THE APPLICABLE
 PROPERTY OWNER.THIS INCLUDES BUT IS NOT
 LIMITED TO THE CONTROL OF DUST, NOISE,
 WATER OR DRAINAGE RUN-OFF, DEBRIS, AND
 THE STORAGE OF CONSTRUCTION MATERIALS.
 NEW CONSTRUCTION ACTIVITY SHALL NOT
 ADVERSELY IMPACT HISTORIC SURFACE WATER
 DRAINAGE FLOWS SERVING ADJACENT
 PROPERTIES, & MAY REQUIRE SPECIAL
 DRAINAGE DESIGN COMPLYING WITH
 ENGINEERING STANDARDS TO PRESERVE THE
 POSITIVE PATTERNS OF THE AFFECTED
 SITES.ACCORDINGLY, DEVELOPERS,
 CONTRACTORS, AND OWNERS OF ALL NEW
 RESIDENTIAL DEVELOPMENET, INCLUDING
 ADDITIONS, POOLS, PATIOS, DRIVEWAYS,
 DECKS, OR SIMILAR ITEMS, ON EXISTING
 PROPERTIES RESULTING IN A DECREASE IN
 EXCESS OF 800SQ FT OF PERMEABLE LAND
 AREA ON ANY PARCELL SHALL AS A PERMIT
 CONDITION, PROVIDE A PROFESSIONALY
 PREPARED DRAINAGE PLAN CLEARLY
 INDICATING COMPLIANCE WITH THIS
 PARAGRAPH. UPON COMPLETION OF THE
 IMPROVEMENT, A CERTIFICATE FROM A
 LICENSED ENGINEER SHALL BE SUBMITTED TO
 THE INSPECTOR IN ORDER TO RECEIVE
 APPROVAL OF THE FINAL INSPECTION.
  
 3)R313.1 SMOKE ALARMS.
 SMOKE ALARMS SHALL BE INSTALLED IN THE
 FOLLOWING LOCATIONS:
 1.IN EACH SLEEPING ROOM.
 2.OUTSIDE EACH SEPARATE SLEEPING
 AREA IN THE IMMEDIATE VICINITY OF THE
 BEDROOMS.
  
  
 4)R313.1.1 ALTERATIONS, REPAIRS AND
 ADDITIONS.
 WHEN INTERIOR ALTERATIONS, REPAIRS OR
 ADDITIONS REQUIRING A PERMIT OCCUR, OR
 WHEN ONE OR MORE SLEEPING ROOMS ARE
 ADDED OR CREATED IN EXISTING DWELLINGS,
 THE INDIVIDUAL DWELLING UNIT SHALL BE
 PROVIDED WITH SMOKE ALARMS LOCATED AS
 REQUIRED FOR NEW DWELLINGS; THE SMOKE
 ALARMS SHALL BE INTERCONNECTED AND HARD
 WIRED.
  
 5) FBC 13-103.1.2 BEFORE A BUILDING
 PERMIT CAN BE ISSUED, THE SUBMITTED
 ENERGY CODE COMPLIANCE FORMS SHALL BE
 SIGNED BY THE BUILDING OWNER, THE
 OWNER'S ARCHETECT OR OTHER AUTHORIZED
 AGENT LEGALLY DESIGNATED BY THE OWNER.
  
 6) FBC 1209.2ACCESS TO ATTIC SPACE
 EACH ATTIC SPACE WITH A CLEAR HEIGHT OF
 24" OR GREATER SHALL BE PROVIDED WITH AN
 INTERIOR ATTIC ACCESS OPENING NOT LESS
 THAN 20"X 30".
  
 7) FOR THE FLAT ROOF, PLEASE INDECATE BY
 HI-LIGHT OR CIRCLE WHICH SYSTEM WILL BE
 USED.IS THE ROOF INSULATED OR
 NON-INSULATED?
  
 MYRON JACOBS
 BUILDING PLAN REVIEWER
 805-6726
  
  
  
  
  
  
Review Stop E ELECTRICAL
Rev No 3 Status P Date 2006-05-03 Cont ID  
Sent By btrobaug Date 2006-05-03 Time 09:58 Rev Time 0.50
Received By btrobaug Date 2006-05-03 Time 08:56 Sent To PC
Notes
***NONE***
Review Stop E ELECTRICAL
Rev No 2 Status P Date 2006-03-09 Cont ID  
Sent By btrobaug Date 2006-03-09 Time 16:23 Rev Time 0.50
Received By btrobaug Date 2006-03-09 Time 15:02 Sent To M
Notes
2006-03-09 00:00:00 
 PROVISO
  
 PLEASE MAKE THE FOLLOWING CORRECTIONS
 FOR CODE COMPLIANCE AND RESUBMIT FOR
 REVIEW PRIOR TO ROUGH INSPECTIION.
  
 1} PLEASE SEE CIRCUIT #22 HAS THE WRONG
 OCP LISTED @ 30AMPS.
  
 2} VERIFY LOCATION OF PANEL "A",
 INDICATED AS METER. ALSO PANEL "B" IS
 INDICATED AS A METER. INDICATE THE
 LOCATION OF ALL SERVICE EQUIPMENT ON THE
 PLAN, AND CORRECTLY LABEL THEM.
  
 3} THE DISCONNECTS AT THE A/C UNITS NEED
 TO COMPLY WITH 110.26 CLEARANCE.
  
 4} IF THE GENERATOR LOCATED BEHIND THE
 GARAGE IS TO BE PART OF THIS PERMIT IT
 MUST BE PROPERLY LOCATED IN THE RISER,
 AND ALL NECESSARY PAPERWORK MUST BE
 SUBMITTED. SEE ATTACHED APPLICATION
 REQUIREMENTS
  
 IF THER ARE ANY QUESTIONS PLEASE CALL.
  
 BILL TROBAUGH
 ELECTRICAL PLAN REVIEW
 561/805-6718
 [email protected]
 FAX/:561/659-8026
  
Review Stop E ELECTRICAL
Rev No 1 Status F Date 2006-02-01 Cont ID  
Sent By btrobaug Date 2006-02-01 Time 18:49 Rev Time 0.75
Received By btrobaug Date 2006-01-27 Time 17:33 Sent To P
Notes
2006-02-01 00:00:00 
 PLEASE MAKE THE FOLLOWING CORRECTIONS
 FOR CODE COMPLIANCE AND RESUBMIT FOR
 REVIEW.
  
 1} PLEASE SEE CIRCUIT #22 HAS THE WRONG
 OCP LISTED @ 60AMPS.
  
 2} VERIFY LOCATION OF PANEL "A",
 INDICATED AS METER.THE SERVICE
 DISCONNECTING MEANS SHALL BE INSTALLED
 AT A READILY ACCESSIBLE LOCATION EITHER
 OUTSIDE OF A BUILDING OR STRUCTURE OR
 INSIDE NEAREST THE POINT OF ENTRANCE OF
 THE SERVICE CONDUCTORS.230.70(A)(1). A
 DISCONNECT IS REQUIRED OUTSIDE IF THE
 SERVICE IS RAN THROUGH THE RESIDENCE.
  
 3} A SMOKE DETECTOR IS REQUIRED IN THE
 ROOM DESIGNATED AS "OFFICE" AND ALSO
 OUTSIDE PER R313.1 FBC (RESIDENTIAL).
 THIS ROOM IS A BEDROOM BY DEFINITION.
  
 4} BEDROOM#1,2, SITTING AREA, AND THE
 MASTER BEDROOM ALL NEED ADDED
 RECEPTACLES TO COMPLY WITH 210.52.ALSO
 SMOKE DETECTORS PER 313.1 FBC
  
 IF THERE ARE ANY QUESTIONS PLEASE CALL.
  
 BILL TROBAUGH
 ELECTRICAL PLAN REVIEW
 561/805-6718
 [email protected]
 FAX/:561/659-8026
  
  
  
Review Stop I INCOMING/PROCESSING
Rev No 6 Status N Date 2006-10-11 Cont ID  
Sent By adarroug Date 2006-10-11 Time 13:51 Rev Time 0.00
Received By adarroug Date 2006-10-11 Time 13:51 Sent To P
Notes
2006-10-11 13:51:36TO "P" BOX/REV
Review Stop I INCOMING/PROCESSING
Rev No 5 Status N Date 2006-05-17 Cont ID  
Sent By adarroug Date 2006-05-17 Time 15:20 Rev Time 0.00
Received By adarroug Date 2006-05-17 Time 15:20 Sent To M
Notes
2006-05-17 00:00:00TO "M" BOX/REV
Review Stop I INCOMING/PROCESSING
Rev No 4 Status N Date 2006-05-17 Cont ID  
Sent By adarroug Date 2006-05-17 Time 15:00 Rev Time 0.00
Received By adarroug Date 2006-05-17 Time 14:55 Sent To P
Notes
2006-05-17 00:00:00TO "P" BOX/REV
Review Stop I INCOMING/PROCESSING
Rev No 3 Status N Date 2006-03-06 Cont ID  
Sent By adarroug Date 2006-03-06 Time 16:28 Rev Time 0.00
Received By adarroug Date 2006-03-06 Time 16:28 Sent To Z
Notes
2006-03-06 00:00:00TO "Z" BOX/RESUB
Review Stop I INCOMING/PROCESSING
Rev No 2 Status N Date 2006-01-27 Cont ID  
Sent By adarroug Date 2006-01-27 Time 09:00 Rev Time 0.00
Received By adarroug Date 2006-01-27 Time 09:00 Sent To E
Notes
2006-01-27 00:00:00TO "E" BOX
Review Stop I INCOMING/PROCESSING
Rev No 1 Status N Date   Cont ID  
Sent By   Date 2006-02-21 Time   Rev Time 0.00
Received By adarroug Date 2006-01-05 Time 10:37 Sent To  
Notes
2006-01-05 00:00:00TO "Z" BOX
Review Stop M MECHANICAL (A/C)
Rev No 4 Status F Date 2006-06-07 Cont ID  
Sent By tgordon Date 2006-06-07 Time 14:45 Rev Time 0.30
Received By tgordon Date 2006-06-07 Time 14:45 Sent To  
Notes
2006-06-07 00:00:00*** DENIED ***
 (REVISION TO MECH. PLANS PAGE M-2.)
 1) THE RETURN AIR DUCT NEEDS TO BE AS
 LARGE OR LARGER THEN THE TWO SUPPLY AIR
 DUCTS ADDED TOGETHER.
  
 2) ARE YOU INSTALLING A TOTAL OF FOUR
 12"X12" RETURN AIR GRILLS TO AIR HANDLER
 # 2. PLEASE CLARIFY.
  
 3) PLEASE SHOW LOCATION OF AIR HANDLER
 #2 ON PLANS.
  
 MECHANICAL PLAN REVIEW BY;
 TOM GORDON (561) 805-6729.
Review Stop M MECHANICAL (A/C)
Rev No 3 Status F Date 2006-05-18 Cont ID  
Sent By tgordon Date 2006-05-18 Time 10:47 Rev Time 0.30
Received By tgordon Date 2006-05-18 Time 10:47 Sent To  
Notes
2006-05-18 00:00:00*** DENIED ***
 1) PLEASE SUBMITMANUAL J CALCULATIONS,
 PER 2004 FBC 13-607.1.ABC.1 .
  
 2) PLEASE SHOW LOCATIONOF CONDENSER
 UNITS AND DRAIN LINES ON MECHANICAL
 PLANS.
  
 3)CONSTRUCTION DOCUMENTS SHALL BE OF
 SUFFICIENT CLARITY. PER 2004 FBC 106.1.1
 .
  
 MECHANICAL PLAN REVIEW BY;
 TOM GORDON (561) 805-6729.
  
Review Stop M MECHANICAL (A/C)
Rev No 2 Status P Date 2006-03-10 Cont ID  
Sent By tgordon Date 2006-03-10 Time 12:14 Rev Time 0.45
Received By tgordon Date 2006-03-10 Time 12:14 Sent To Z
Notes
***NONE***
Review Stop M MECHANICAL (A/C)
Rev No 1 Status F Date 2006-02-02 Cont ID  
Sent By tgordon Date 2006-02-02 Time 15:24 Rev Time 1.00
Received By tgordon Date 2006-02-02 Time 15:24 Sent To B
Notes
2006-02-02 00:00:00*** DENIED ***
 1) ENERGY CALCULATIONS ARE MISSING THE
 MANUAL J SECTION OF THEM, NEED MANUAL J
 SHOWING THE DUCT SIZE.
  
 2) ENERGY CALCULATIONS NEED TO BE SIGNED
 BY OWNER/AGENT.
  
 3) ENERGY CAL'S ARE CALLING FOR TWO
 55,000 TOTAL BTU SYSTEMS, MECHANICAL
 PLANS ARE SHOWING TWO 36,000 TOTAL BTU
 SYSTEMS PLEASE CORRECT & PROVIDE MANUAL
 J.
  
 4) MECHANICAL PLANS MUST SHOW JOB
 ADDRESS, NAME OF COMPANY THAT DESIGNED
 MECH. PLANS, CO. ADDRESS, CO. TELEPHONE
 NUMBER, CO. LICENSE NUMBER, AND NAME &
 SIGNATURE OF THE PERSON RESPONSIBLE FOR
 THE DESIGN ,ON THEM.
  
 5) 1ST. FLOOR BATHROOM AND MASTER
 BATHROOM WHERE TUB IS, MAY NEED AN
 EXHUST FAN PLEASE SEE 2004 FBC/R303.3 .
  
 6) NEED TO SHOW CLOTHES DRYER EXHUST
 DUCT ON MECH. PLANS.
  
 7) AHU #1. NO RETURN AIR PROVIDED FOR
 DINING ROOM, KITCHEN, FAMILY ROOM, &
 LIVING ROOM DUE TO DOOR IN HALLWAY, SEE
 NOTE #11.
  
 8) AHU #1 & 2. RETURN AIR GRILL AND DUCT
 (FLEX) IS TO SMALL FOR A 3 TON UNIT.
  
 9) AHU #2. NO RETURN AIR PROVIDE FOR
 MASTER SUITE DUE TO DOORS, SEE NOTE #11.
  
 10) RETURN AIR TRANSFER DUCT TO BEDROOM
 #1 IS TO SMALL, SEE NOTE #11.
  
 11)BALANCED RETURN AIR.
 THIS MAY BE ACHIEVED BY.
 (A)TRANSFER DUCTS MAY ACHIEVE THIS BY
 INCREASING THE RETURN TRANSFER ONE AND
 ONE HALF TIMES THE CROSS SECTIONAL AREA
 (SQUARE INCHES) OF THE SUPPLY DUCT
 ENTERING THE ROOM OR SPACE IT'S SERVING
 AND THE DOOR HAVING AT LEAST AN
 UNRESTRICTED 1 INCHUNDERCUT TO ACHIEVE
 PROPER RETURN AIR BALANCE.
 (B)TRANSFER GRILLES SHALL USE 50
 SQUARE INCHES (OF GRILLE AREA) TO 100
 CFM (OF SUPPLY AIR) FOR SIZING
 THROUGH-THE-WALL TRANSFER GRILLES AND
 USING AN UNRESTRICTED 1-INCH
 UNDERCUTTING OF DOORS TO ACHIEVE PROPER
 RETURN AIR BALANCE
 (C)HABITABLE ROOMS ONLY SHALL BE
 REQUIRED TO MEET THESE REQUIREMENTS FOR
 PROPER BALANCED RETURN AIR EXCLUDING
 BATHROOMS, CLOSETS, STORAGE ROOMS AND
 LAUNDRY ROOMS, EXCEPT THAT ALL SUPPLY
 AIR INTO THE MASTER SUITE SHALL BE
 INCLUDED. PER 2004 FBC/R M1602.4 .
  
 MECHANICAL PLAN REVIEW BY;
 TOM GORDON (561) 805-6729.
  
Review Stop P PLUMBING
Rev No 3 Status P Date 2006-06-06 Cont ID  
Sent By jleech Date 2006-06-06 Time 18:06 Rev Time 0.00
Received By jleech Date 2006-06-06 Time 18:06 Sent To M
Notes
2006-06-06 00:00:00REVISED SANITARY RISER DIAGRAM.
Review Stop P PLUMBING
Rev No 2 Status P Date 2006-03-08 Cont ID  
Sent By jleech Date 2006-03-08 Time 14:57 Rev Time 0.00
Received By jleech Date 2006-03-08 Time 14:56 Sent To E
Notes
***NONE***
Review Stop P PLUMBING
Rev No 1 Status P Date 2006-02-02 Cont ID  
Sent By jleech Date 2006-02-02 Time 07:32 Rev Time 0.33
Received By jleech Date 2006-02-02 Time 07:32 Sent To M
Notes
***NONE***
Review Stop Z ZONING
Rev No 2 Status P Date 2006-03-22 Cont ID  
Sent By mmclean Date 2006-03-22 Time 11:47 Rev Time 0.00
Received By mmclean Date 2006-03-22 Time 11:47 Sent To  
Notes
***NONE***
Review Stop Z ZONING
Rev No 1 Status F Date 2006-01-26 Cont ID  
Sent By mmclean Date 2006-01-26 Time 18:17 Rev Time 0.00
Received By mmclean Date 2006-01-26 Time 18:17 Sent To I
Notes
2006-01-26 00:00:00DENIED,
 1. NEED TO PROVIDE THE LOCATION OF THE
 DRIVEWAY WITH DIMENSION (LENGTH & WIDTH
 ON TWO COPY OF SURVEY.
 2. HISTORIC PROVISO THAT THE CIRCULAR
 DRIVEWAY BE REMOVED.PLEASE ADDRESS ON
 TWO COPY OF SURVEY.
  
  
 NOTE: MUST MAINTAIN 1000SQ FT OR 75% OF
 LANDSCAPE, WHICHEVER IS LESS WITHIN THE
 FIRST 25FT FRONT SETBACK.
  
  
 MICHELLE MCLEAN
 ZONING TECHNICIAN
 805-6720


Account Summary | Usage Policy | Privacy Policy
Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved