City of West Palm Beach eGovPlus

Plan Review Details - Permit 05091410

Plan Review Stops For Permit 05091410

Review Stop	AD			ADDRESSING
Rev No	1	Status	P	Date	2006-05-16			Cont ID
Sent By	lursu			Date	2006-05-16	Time	15:25	Rev Time	0.00
Received By	lursu			Date	2006-05-16	Time	15:25	Sent To

Notes

2006-05-16 00:00:00	PERMIT ATTACHED TO EXT#0006 FOR BLDG 10
	:4565 MIRADOR LN
2006-05-15 00:00:00	NEEDS!!!

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2006-06-20			Cont ID
Sent By	rmcdouga			Date	2006-06-20	Time	10:40	Rev Time	0.00
Received By	rmcdouga			Date	2006-06-20	Time	10:40	Sent To	M

Notes

2006-06-20 00:00:00	DENIED

	1) THE PLANS MUST BE STAMPED BY PALM
	BEACH COUNTY FOR IMPACT FEES. THE PLAN
	REVIEW NUMBER ON THE PLANS MUST
	CORRESPOND WITH THE P.R. NUMBER ON THE
	IMPACT FEE RECEIPT.

	2) SUBMIT FIRE SPRINKLER PLANS FOR THE
	REQUIRED NFPA 13 SYSTEM. THIS IS
	REQUIRED BY FBC 104.3.1.1 OF THE CITY OF
	W.P.B. AMENDMENTS TO THE 2001 FBC.

	3) THE GARAGE FLOOR/CEILING ASSEMBLY IN
	DETAIL 17 ON A 10.0.0 DOES NOT
	CORRESPOND TO THE FC 5517 FIRE RATED
	ASSEMBLY LISTED IN THE GYPSUM
	ASSOCIATION MANUAL. PLEASE CORRECT.

	4) NUMBER 20 ON THE DOOR SCHEDULE
	SPECIFIES A VENTED GARAGE DOOR. THE
	PRODUCT APPROVAL FOR THE GARAGE DOOR
	DOES NOT INDICATE VENTS IN THE DOOR.

	5) REVISE DETAIL 11 ON A 10.0.0 TO
	SPECIFY THE 2001 FBC AND NOT THE CURRENT
	EDITION OF THE STANDARD BUILDING CODE.

	6) THE DRAWINGS ATTACHED TO THE STATE
	PRODUCT APPROVAL FOR THE STEEL DOOR FROM
	MASONITE INTERNATIONAL ARE FOR A 6'-8"
	DOOR AND THE PLAN SPECIFIES AN 8'-0"
	DOOR. SEE FL 4940.3 AND DRAWING
	DWG-MA-FLO 133-05.

	7) SUBMIT PRODUCT APPROVALS FOR THE
	TRUSS CONNECTORS. (SIMPSON-HETAL 12 &
	16, USP-USC) THE FL COVERSHEET SUBMITTED
	FOR THE USP HANGERS AND COLUMN BASES &
	CAPS HAS A WINDOW MULLION NOA ATTACHED
	TO IT.

	8) THE MIAMI-DADE NOA FOR THE SINGLE
	HUNG WINDOWS IS INCOMPLETE. THERE ARE
	SHEETS WITH ANOTHER NOA NUMBER ATTACHED
	AT THE REAR OF THE SH WINDOW NOA.

	9) THE DECORATIVE BAHAMA SHUTTERS WILL
	REQUIRE A SEPARATE PERMIT.

	10) FS 713.13 IF THE IMPROVEMENT
	DESCRIBED IN THE NOTICE OF COMMENCEMENT
	IS NOT ACTUALLY COMMENCED WITHIN 90 DAYS
	AFTER THE RECORDING THEREOF, SUCH NOTICE
	IS VOID AND OF NO FURTHER EFFECT.
	(THE NOC WILL NEED TO BE RE-RECORDED
	BEFORE THE PERMIT IS ISSUED.)

	11) FBC 13-600.3ABC.1.2 REQUIRES THE
	ENERGY CALCULATION FORMS TO BE SIGNED
	AND SEALED BY AN ARCHITECT OR AN
	ENGINEER.

	12) SUBMIT PRODUCT APPROVALS FOR THE
	8 X 8 IMPACT RESISTANT SLIDING GLASS
	DOORS.

	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2006-02-07			Cont ID
Sent By	rmcdouga			Date	2006-02-07	Time	13:57	Rev Time	0.00
Received By	rmcdouga			Date	2006-02-07	Time	13:57	Sent To

Notes

2006-02-07 00:00:00	DENIED

	1)A RECORDED COPY OF THE NOTICE OF
	COMMENCEMENT MUST BE SUBMITTED BEFORE A
	PERMIT CAN BE ISSUED.

	2) THE PROPOSED PROJECT APPEARS TO
	COMPRISE MORE THAN ONE PARCEL. PLEASE
	SUBMIT A COPY OF THE REPLAT.

	3) IN ORDER TO DETERMINE THE PERCENTAGE
	OF WALL AREA ALLOWED AS OPENINGS BY FBC
	TABLE 600, SUBMIT A SURVEY INDICATING
	THE LOCATIONS OF THE ASSUMED PROPERTY
	LINES BETWEEN THE BUILDINGS.

	4) PROVIDE AN AREA CALCULATION TABLE
	LISTING THE FLOOR AREA BREAKDOWNS BY
	FLOOR FOR EACH UNIT AND THE TOTALS FOR
	ALL FOUR UNITS.

	5) THE FBC DOES NOT ALLOW HEIGHT AND
	AREA INCREASES FOR NFPA 13R SPRINKLER
	SYSTEMS. SEE FBC TABLE 500 FOOTNOTE (D).
	SPECIFY THE TYPE OF SPRINKLER SYSTEM ON
	THE PLANS. MUST BE A FULL NFPA 13 SYSTEM
	FOR HEIGHT INCREASE. SUBMIT FIRE
	SPRINKLER PLANS PER FBC 104.3.1.1.

	6) FBC 2504.4.1 AND GA 216 REQUIRE WOOD
	FURRING TO BE NOT LESS THAN 3/4" X
	1-1/2" ACTUAL SIZE. ALSO, THE SURFACE
	CAN NOT VARY MORE THAN 1/8" FROM THE
	PLANE OF ADJACENT FURRING MEMBERS.
	DETAIL 1 ON A10.0.0 SHOWS THE FURRING
	ATTACHED OVER 3/4" POLYSTYRENE. PLEASE
	REVISE DETAIL TO COMPLY WITH CODE.

	7) SPECIFY THE INSULATION THAT WILL BE
	USED IN THE FLOOR/CEILING ASSEMBLY ABOVE
	THE GARAGE.

	8) THE GUTTER DOWNSPOUTS ARE REQUIRED TO
	DISCHARGE ONE FOOT AWAY FROM THE
	STRUCTURE PER FBC 1503.4.4.

	9) SHOW COMPLIANCE WITH FBC MECH. TABLE
	403.3 FOR REQUIRED OUTDOOR AIR
	VENTILATION AT GARAGES OF 100 CFM PER
	CAR.

	10) ON SHEET A-4.8.1 TWO BEDROOMS ARE
	LABELED BEDROOM #2.

	11) SPECIFY THE EXTERIOR FINISH AT THE
	UNDERSIDE OF THE BAY WINDOW SHOWN ON
	A-7.1.2. SPECIFY THE EXTERIOR SHEATHING,
	LATH AND STUCCO. NOTE: SEE ASTM C 926
	FOR REQUIRED STUCCO THICKNESS.

	12) ASTM C 926 REQUIRES 7/8" OF STUCCO
	WHEN APPLIED VERTICALLY ON METAL PLASTER
	BASE OVER SOLID BASE. PLEASE REVISE NOTE
	#46 FOR SECTION 4 ON A-7.0.2.

	13) SPECIFY THE MEAN ROOF HEIGHT OF THE
	STRUCTURE. THIS IS THE VERTICAL DISTANCE
	FROM FINISHED GRADE TO THE A POINT AT
	THE AVERAGE HEIGHT OF THE ROOF.

	14) SUBMIT SHOP DRAWINGS FOR THE BALCONY
	GUARDRAILS. SPECIFY ATTACHMENTS, SPACING
	OF INTERMEDIATE RAILS, ETC.

	15) SPECIFY THE METHOD OF ATTACHMENT FOR
	THE ROOF TILES. THE PRODUCT APPROVAL
	THAT WAS SUBMITTED HAS AN ATTACHMENT
	RESISTANCE MOMENT OF 24.5 FT-LBF FOR
	MORTAR SET TILE. FOR 140 MPH EXPOSURE B
	WITH 40FT MRH, THE REQUIRED MOMENT IS
	28.3 FT-LBF. PLEASE REVISE ROOF TILE
	DETAILS TO COMPLY WITH CODE.

	16) UL ASSEMBLY U 906 HAS A 2 HOUR FIRE
	RATING NOT ONE HOUR AS SPECIFIED ON THE
	PLANS FOR WALL TYPES IN DETAILS 2 AND 6
	ON A-10.00.

	17) SPECIFY DRAFTSTOPPING IN THE ROOF
	OVERHANGS IN LINE WITH THE TENANT
	SEPARATION WALLS AS REQUIRED BY FBC
	2305.2.3.

	18)705.7.1 JOINTS INSTALLED IN OR
	BE- TWEEN FIRE RESISTANT WALLS, FIRE
	RESIS- TANT FLOORS OR FLOOR/ CEILING
	ASSEMBLIES AND FIRE RESISTANT ROOFS OR
	ROOF/ CEILING ASSEMBLIES SHALL BE
	PROTECTED BY AN APPROVED FIRE RESISTANT
	JOINT SYSTEM DESIGNED TO RESIST THE
	PASSAGE OF FIRE FOR A PERIOD NOT LESS
	THAN THE REQUIRED FIRE RESISTANCE RATING
	OF THE WALL, FLOOR OR FLOOR IN OR
	BETWEEN WHICH IT IS INSTALLED. SPECIFY
	THE JOINT SYSTEM AT THE TOP OF THE
	TENANT SEPARATION WALLS.

	19) DETAIL 17 ON A-10 DOES NOT
	CORRESPOND TO GA ASSEMBLY FC 5517
	SPECIFIED ON SHEET A 10.2.0.

	20) SUBMIT SIGNED AND SEALED TRUSS
	LAYOUTS AND DRAWINGS THAT HAVE BEEN
	REVIEWED AND APPROVED BY THE DESIGNER OF
	RECORD FOR THE STRUCTURE.

	21) THE UPLIFT LOAD VALUES LISTED IN THE
	TRUSS ANCHOR SCHEDULE ON S-3 FOR THE
	SIMPSON HETAL 16 & 20 ARE INCORRECT.THE
	ONE THIRD STRESS INCREASE FOR STEEL
	CALCULATIONS IS NO LONGER ALLOWED. SEE
	THE 2005 SIMPSON CATALOG.

	22) THE HUGHES "USC" CONNECTORS ALSO
	HAVE INCORRECT UPLIFT VALUES. HUGHES WAS
	PURCHASED BY USP SEVERAL YEARS AGO AND
	IS LONGER IN BUSINESS. SEE THE 2005 USP
	CATALOG FOR VALUES. UPDATE THE TRUSS
	ANCHOR SCHEDULE.

	23) UNDER KEY NOTES/ LEGEND ON A-4.0 AND
	OTHER SHEETS REFERENCE IS MADE TO SHEET
	A-13 FOR THE WALL TYPES. HOWEVER, THERE
	IS NO SHEET A-13.

	24) THE ENERGY CALCULATIONS CONTAIN
	SEVERAL ERRORS. THESE ARE CONSIDERED
	MULTIFAMILY NOT SINLE FAMILY. THE
	ADJACENT WALL AT THE GARAGE IS METAL
	FRAME AND THE CEILING INSULATION IS
	SPECIFIED AS R-20 ICYENE.

	25)PROVIDE MANUFACTURER'S SPECIFICATIONS
	FOR THE ICYENE INSULATION.

	26) PRODUCT APPROVALS SUBMITTED
	WITH PERMIT APPLICATION AFTER OCTOBER 1,
	2003 ARE REQUIRED TO COMPLY WITH THE
	FLORIDA PRODUCT APPROVAL SYSTEM. FOR
	INFORMATION PLEASE SEE THE STATE WEBSITE
	AT WWW.FLORIDABUILDING.ORG. PRODUCTS
	WITH STATEWIDE APPROVAL ARE REQUIRED TO
	BE SUBMITTED WITH A COVER SHEET THAT
	LISTS THE PRODUCT IDENTITY NUMBER FROM
	THE STATE. IF THE PRODUCT DOES NOT HAVE
	STATEWIDE APPROVAL, SUBMIT AN APPLICA-
	TION FOR LOCAL PRODUCT APPROVAL OR SITE
	SPECIFIC FORM PER RULE 9B-72. SUBMIT
	FLORIDA COVER SHEETS FOR ALL PRODUCT
	APPROVALS. IN ADDITION TO THE COVERSHEET
	THE INSTALLATION INSTRUCTIONS OR PRODUCT
	EVALUATION AS LISTED ON THE STATE
	WEBSITE IS ALSO REQUIRED. TWO (2) COPIES
	ARE REQUIRED.

	27) SUBMIT STATE PRODUCT APPROVALS FOR
	THE TRUSS CONNECTORS.

	28) THE MIAMI-DADE NOA FOR THE SINGLE
	HUNG WINDOWS HAS THE INFO FROM THE FIXED
	GLASS WINDOWS ATTACHED TO THE NOA
	COVERSHEET.

	29) THE DESIGN PRESSURES LISTED IN THE
	GARAGE DOOR PRODUCT APPROVALS DO NOT
	MEET THE PRESSURES SPECIFIED ON THE
	PLANS. SEE S-6.

	30) SUBMIT MANUFACTURER'S SPECS. FOR THE
	DOOR CLOSERS.


	ROBERT MCDOUGAL
	BLDG. PLAN REVIEW
	(561)805-6714

Review Stop	E			ELECTRICAL
Rev No	2	Status	P	Date	2006-05-15			Cont ID
Sent By	dpalmer			Date	2006-05-15	Time	12:46	Rev Time	0.00
Received By	dpalmer			Date	2006-05-15	Time	12:17	Sent To

Notes

2006-05-15 00:00:00	*** NOTES REDLINED *****

	** PLANS MUST BE REVISED IF PLANS COME
	BACK FOR ANY OTHER COMMENTS FROM OTHER
	TRADES. IF ALL REVIEWS PASS, THEN PLANS
	ARE TO BE REVISED "BEFORE SLAB
	INSPECTION">


	** PLEASE SEE NO, SERVICE ENTRANCE
	CONDUIT OR SERVICE ENTRANCE CONDUCTORS
	ARE SHOWN ON RISER FROM FPL TO 1000A
	SERVICE MAIN.
	PLEASE SEE SEC'S ARE NOTED IN FAULT
	CURRENT CALCS ONLY.

	** PLEASE SEE #4 GEC SHOWN, WHERE A 3/0
	MIN IS REQUIRED PER 250.66.



	IF THERE ARE ANY QUESTIONS, PLEASE CALL.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW
	561-805-6717
	[email protected]

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2005-10-17			Cont ID
Sent By	dpalmer			Date	2005-10-17	Time	13:19	Rev Time	0.00
Received By	dpalmer			Date	2005-10-17	Time	13:18	Sent To

Notes

2005-10-17 00:00:00	******* UNSAT *******


	1)NOTE: PLEASE SEE PROJECT IS SUBMITTED
	AS CONDO'S YET ELECTRICALSERVICES
	PROVIDED IS SHOWN AS EACH WOULD BE A
	TOWNHOUSE (FEE SIMPLE).
	PLEASE SEE WATER SERVICE SHOWS
	MULTI-FAMILY BLDG.
	PLEASE KNOW, IF THESE AS MULTI-FAMILY
	CONDO BLDGS; ONE SERVICE FOR EACH BLDG
	IS PERMITTED,230.2,230.70MAINS WILL BE
	REQUIRED TO BE GROUPED PER 230.72.
	MCB'S SHOWN IN EACH GARAGE PANEL IS
	PERMITTED.
	PLEASE ADJUST SERVICE FOR BLDG.

	2)NOTE: PLEASE SUBMIT AIC RATINGS FOR
	ALL NEW SERVICE EQUIPMENT BEING INSTALL-
	ED. MAINS/BRKRS AND PANELS ARE ALL TO BE
	RATED FOR THE AVAILABLE FAULT CURRENT.
	PER 110.9/215.5
	AIC RATINGS ARE SHOWN FOR EACH PANEL,
	BUT WILL ALSO BE REQUIRED FOR MAINS.(NEW
	SERVICE).

	3)NOTE: PLEASE CLARIFY LOCATION OF
	DISHWASHER RECEPT. APPEARS TO BE SHOWN
	BEHIND UNIT? THIS IS ONLY A NOTE:

	4))NOTE: PLEASE SEE RECEPTS SERVING
	KITCHEN COUNTERSPACE TO MEET 210.52C-
	SEC'S 1,2,3,4 AND 5
	PLEASE SEE PLANS REDLINED FOR SOME
	MISSING

	5)NOTE: PLEASE SHOW OUTLET SPACING PER
	210.52.DFOR MISSING BATH WITH 3' OF
	LAV EDGE. PLEASE ADD ONE OR MORE
	EXISTING TO CENTER.

	6)NOTE: PLEASE SEE LOCATION WASHER/DRYER
	APPEARS TO SHOW ONLY ONE RECEPTS FOR
	DRYER, ALTHOUGH PANEL SCHEDULES SHOWS
	WASHER CIRUIT ALSO.

	7 )NOTE: PLEASE SEE 220.3B4.
	PLEASE SHOW ALL RECESSED LTS BASED ON
	MAX WATTAGE FOR FIXTURE(S). THIS NEEDS
	TO BE SHOWN ABOVE THE GEN. KT/RECEPT
	LOADS. THIS SHOULD BE ABOVE THE FIGURED
	3W/PER SQ FT.
	PLEASE PROVIDE FIXTURE INFORMATION ON
	LEGEND.

	8)NOTE: PLEASE LIST ALL THE REQUIRD ARC
	FAULT PROECTED CIRCUITS AS REQUIRED PER
	2002 210.12
	PLEASE KNOW, SD'S ARE BEING SHOWN
	CIRCUITED TO KITCHEN LIGHTING CIRCUIT,
	THIS IS OK, HOWEVER PLEASE KNOW, THIS
	WOULD ALSO REQUIRE ARC FAULT PROTECTION
	FOR THIS ADDITIONAL CIRCUIT.
	THIS IS ONLY A NOTE:

	9)NOTE: PLEEASE SEE NFPA-72 (2002)
	EDITION,11.8.3.5.
	PLEASE PLACE NOTE ON PLANS WHICH STATES
	LOCATIONS OF SD'S TO BE A MIN OF 3' FROM
	BATH(S) AND KITCHEN DOORS AND 20' FROM
	KITCHEN COOKING APPLIANCES.
	** PLEASE SEE EXCEPTION TO 20' FROM
	COOKING WITH TYPE OF SD USED.**
	PLEASE SEE PLANS SHOWS A SD IN KITCHEN
	AREA AT THIS TIME.

	10)NOTE: PLEASE SEE MECHANICAL NOTES
	PERTAINING TO "DRYER BOOSTER FANS".
	AS PER MECHANICAL THESE MAY NOT BE
	PERMITTED AND ANY COMMENT THEY MAY HAVE
	WILL DIRECTLY AFFECT ELECTRICAL PLANS.
	THIS IS A NOTE, AS IT IS NOT AN NEC
	ISSUE.
	PLEASE SEE ALL SYSTEMS DO HAVE BE
	LISTED.110.3,90.7
	PLEASE KNOW, THESE COULD NOT LOCATED ON
	THESE PLANS FOR UNITS "C" AND "D".

	11)NOTE: PLEASE VERIFY OCP FOR AHU HEAT,
	PER 424.3B, MIN 125%.

	12)NOTE: PLEASE SEE RECEPTS SHOWN IN
	CLOSET SBOVE SHELF AREA WILL NOT BE
	PERMITTED. THE RECEPT FOR LV PANEL MAY
	BE OCER DOOR OR OUT OF ROOM ONLY.
	THIS IS RELATED TO LIFE SAFTEY ISSUE AND
	CLOSE PROXIMITY TO EASILY IGNITIBLE
	MATERIALS.240.24D


	13)NOTE: PLEASE SEE PLANS DO NOT
	INDICATE ANY ACCESIBLITY TO GFI RECEPTS
	SHOWN FOR JACUZZI/WHIRLPOOL TUB.

	14)NOTE: PLEASE SEE 406.2B,210.21B3&4
	WHICH REQUIRES THE MAX OCP FOR A 50A
	RANGE RECEPT TO BE 50A'S. PLEASE SEE A
	2P-60A BRKR IS SHOWN.

	15)NOTE: PLEASE PROVIDE AREA AND ROOM
	DESIGNATIONS ON PLANS. PLEASE SEE SOME
	ARE MISSING.
	THIS WILL ALSO BE REQUIRED TO DETERMINE
	CIRCUITING FOR DINING AREAS.

	16)NOTE: PLEASE SEE PLANS REFERENCE THE
	2000 NFPA 101, WHEN AS OF JAN 1ST 2005,
	THE 2003 NFPA-101 IS IN EFFECT.

	** PLEASE KNOW, MANY ITEMS HAVE BEEN
	REDLINED ON PLANS FOR LOCATIONS OF
	NOTES.

	** PLEASE KNOW, A REVIEW OF MAIN
	ELECTRICAL SERVICECAN NOT BE DONE AT
	THIS TIME, AS SERVICE WILL BE CHANGING.

	PLEASE SEE ANY OTHER POSSIBLE COMMENTS
	FROM OTHER TRADES WHICH MAY AFFECT
	ELECTRICAL PLANS.

	PLEASE REMOVE ALL OLD/VOIDED SHEETS AND
	ONLY INSERT NEW REVISED SHEETS INTO
	COMPLETE SETS FOR REVIEW AND STAMPING.

	** PLEASE SEE THIS MAY BE CONSIDERED A
	"THRESHOLD" PROJECT. IF SO, THREE SETS
	OF PLANS WILL BE REQUIRED.

	PLEASE SUBMIT THE ABOVE INFORMATION FOR
	REVIEW. IF THERE ARE ANY QUESTIONS,
	PLEASE DO NOT HESITATE IN CONTACTING
	THIS OFFICE.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW
	CITY OF WEST PALM BEACH
	CONSTUCTION SERVICES DEPT.
	561-805-6717
	[email protected]

Review Stop	ENG			ENGINEERING CSD
Rev No	1	Status	P	Date	2005-09-30			Cont ID
Sent By	mamini			Date	2005-09-30	Time	10:26	Rev Time	0.50
Received By	mamini			Date	2005-09-30	Time	10:26	Sent To

Notes

2005-09-30 00:00:00	PASSED:

	1. SEE PERMIT # 04120439 FOR UNDERGROUND
	UTILITIES AND SITE WORK.

	IF ANY QUESTION PLEASE CONTACT 805-6723
	MOHAMMAD R. AMINI

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	2	Status	P	Date	2006-06-27			Cont ID
Sent By	mwennerg			Date	2006-06-27	Time	13:51	Rev Time	0.00
Received By	mwennerg			Date	2006-06-27	Time	13:51	Sent To

Notes

2006-06-27 00:00:00	*PROVISO*

	1) FLORIDA FIRE PREVENTION CODE, 2004
	EDITION SHALL BE REFERENCED. 2001
	EDITION IS CALLED OUT ON A-0.0.0.

	2) PLEASE SEE BUILDING REVIEW COMMENT
	(2) REGARDING THE SUBMITTAL OF FIRE
	PROTECTION SHEETS FOR REVIEW. THE
	SEPARATE SHOP DRAWINGS AND PERMIT WILL
	ALSO BE REQUIRED PRIOR TO SYSTEM
	INSTALLATION.

	PLANS NOT STAMPED UNTIL COMPLIANCE IS
	MET.


	MIKE WENNERGREN, CAPTAIN/WPBFR
	FIRE PLAN REVIEW (561) 805-6722

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	P	Date	2006-02-07			Cont ID
Sent By	mwennerg			Date	2006-02-07	Time	14:39	Rev Time	0.00
Received By	mwennerg			Date	2006-02-07	Time	14:39	Sent To

Notes

2006-02-07 00:00:00	****PROVISO****

	1) LIFE SAFETY TO COMPLY WITH NFPA 101,
	2003 EDITION.

	2) SEPARATE SHOP DRAWINGS AND PERMIT
	REQUIRED FOR FIRE SPRINKLER SYSTEM, THAT
	SHALL BE UL CERTIFIED FOR CENTRAL
	STATION.

	3) MULTI-PURPOSE FIRE EXTINGUISHERS ARE
	REQUIRED FOR EACH UNIT.

	4) AN ADDRESS IS REQUIRED FOR EACH UNIT,
	AND SHALL BE AT LEAST 3" IN HEIGHT AND
	CONTRASTING TO BACKGROUND.

	5) PLANS INDICATE THAT SHOP DRAWINGS FOR
	PRE-ENGINEERED STAIRS WILL BE PROVIDED,
	THAT SHALL BE IN COMPLIANCE WITH NFPA
	101, AND FBC REQUIREMENTS.


	MIKE WENNERGREN, CAPTAIN/WPBFR
	FIRE PLAN REVIEW (561) 805-6722

Review Stop	I			INCOMING/PROCESSING
Rev No	2	Status	N	Date	2006-03-30			Cont ID
Sent By	adarroug			Date	2006-03-30	Time	11:10	Rev Time	0.00
Received By	adarroug			Date	2006-03-30	Time	11:10	Sent To

Notes

2006-04-11 00:00:00	TO "COMM" BD#4
2006-03-30 00:00:00	WAITING FOR "COMM" BD/PLANS ON RACK

Review Stop	I			INCOMING/PROCESSING
Rev No	1	Status	N	Date	2006-02-07			Cont ID
Sent By	rmcdouga			Date	2006-02-07	Time	13:57	Rev Time	0.00
Received By	rmcdouga			Date	2005-09-29	Time	17:54	Sent To

Notes

2005-09-29 00:00:00	TO "COMM" BD#46/PLANS ON
	RACK/APPLICATIONS AND 8 ROLLS

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	P	Date	2006-06-26			Cont ID
Sent By	pkrauss			Date	2006-06-26	Time	07:28	Rev Time	0.00
Received By	pkrauss			Date	2006-06-26	Time	07:28	Sent To	FIRE

Notes

2006-06-26 00:00:00	PROVISO:2001 FBC/BUILDING 10/4 UNIT
	PLEASE REVISE PLANS TO REFLECT THE
	IMPLEMENTATION OF THE PROVISO'S.

	COMMENT #6:SPECIFIC DRYER TO BE
	INSTALLED WHICH WILL ELIMINATE THE NEED
	OF THE BOOSTER FAN.PLEASE NOTE,
	SPECIFIC DRYER IS TO BE INSTALLED FOR
	FINAL INSPECTION 2001 FMC 504.6.

	COMMENT #7:PLAN SHEET M0.1 THE OUTSIDE
	AIR CALCULATIONS ARE BASED ON
	"INFILTRATION RATES".THE INFILTRATION
	RATES ARE "MAXIMUM RATES" ALLOWED BY
	CODE AND MAY NOT ACTUALLY EXIST.THE
	"ACTUAL" RATE IS NOT KNOWN UNLESS
	TESTED.OUTSIDE AIR CALCULATIONS ARE TO
	BE PER 2001 FMC 402.2, 402.2.1 OR TABLE
	403.3.PLEASE PROVIDE CALCULATIONS.
	PLEASE NOTE, PLAN SHEET M2 INDICATES 6"
	OUTSIDE AIR DUCT, PLEASE REMOVE FROM THE
	PLANS IF THIS DUCT IS NOT GOING TO BE
	INSTALLED.

	COMMENT #8:AHU CLOSET IS USED AS A
	RETURN AIR PLENUM.PLAN SHEET M0.1 AHU
	DETAIL 15 ANNOTATES "NO COMBUSTIBLES
	ALLOWED IN THE RETURN AIR PLENUM".
	HOWEVER, PLAN SHEETS A-4.0.2 THROUGH
	A-4.5.3, THE DOOR SCHEDULE INDICATES THE
	AHU CLOSET DOOR WILL BE A WOOD LOUVERED
	DOOR.PLEASE NOTE, THE DOOR AND FRAME
	ARE REQUIRED TO MEET THE 25 FLAME/50
	SMOKE INDEX WHEN TESTED UNDER ASTM 84.
	PLEASE VERIFY THE DOOR & FRAME MEET THIS
	REQUIREMENT PER 2001 FMC 602.2.1.

	IF YOU HAVE ANY QUESTIONS, PLEASE
	CONTACT PATTY KRAUSS AT (561)805-6719.

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2005-11-22			Cont ID
Sent By	pkrauss			Date	2005-11-22	Time	14:47	Rev Time	0.00
Received By	pkrauss			Date	2005-11-22	Time	14:17	Sent To

Notes

2005-11-22 00:00:00	DENIED:BUILDING 10 / 2001 FBC
	1.PLAN SHEET A-0.0.0 PRODUCT
	INFORMATION INDICATES TYPE VI,
	UNPROTECTED SPRINKLERED.PLEASE
	INDICATE WHICH SYSTEM WILL BE UTILIZED -
	(13, 13R, 13D, ETC).PLEASE NOTE,
	ADDITIONAL COMMENTS MAY BE GENERATED BY
	THE RESPONSE GIVEN.

	2.PLAN SHEET M1 INDICATES EXHAUST DUCT
	PENETRATING FIRE RATED WALLS.PLEASE
	SHOW COMPLIANCE WITH 2001 FMC 607.1.3 #3
	ITEMS 1 THROUGH 4.

	3.PLAN SHEET M1 UNIT #88 R/A JUMPER
	FROM THE GUEST SUITE IS NOT SIZED
	PROPERLY.R/A SHOULD BE A MINIMUM OF
	12".PLEASE REVISE.

	4.R/A TRANSFER GRILLES ARE NOT SIZE
	PROPERLY.PLEASE REFERENCE 2001 FMC
	601.4 EXCEPTION #2 & 3 AND SIZE GRILLES
	ACCORDINGLY.

	3.PLAN SHEET M3 THE DRYER EXHAUST
	DUCTS EXCEED THE 25FT REQUIREMENT WITH
	REDUCTIONS FOR THE 90'S PER 2001 FMC
	504.6.

	5.PLEASE PROVIDE OUTSIDE AIR
	CALCULATIONS IN ACCORDANCE WITH 2001 FMC
	TABLE 403.3.

	6.PLEASE PROVIDE DETAIL FOR THE AHU
	LOCATED IN THE CLOSET.PLEASE NOTE,
	MECHANICAL CLOSET SHALL COMPLY WITH 2001
	FMC 603.9 & 610.1.ABC.3.7 OF CHAPTER 13
	OF THE 2001 FBC.

	7.CONDENSATE SHALL TERMINATE A MINIMUM
	OF 12" AWAY FROM THE BUILDING STRUCTURE
	PER 2001 FBC 1503.4.4.

	8.AUXILIARY DRAIN PAN WITH OVERFLOW
	PROTECTION REQUIRED PER 2001 FMC
	307.2.3.

	IF YOU HAVE ANY QUESTIONS, PLEASE
	CONTACT PATTY KRAUSS AT (561)805-6719.

Review Stop	P			PLUMBING
Rev No	2	Status	P	Date	2006-06-20			Cont ID
Sent By	kstevens			Date	2006-05-27	Time	16:37	Rev Time	0.00
Received By	kstevens			Date	2006-05-27	Time	16:37	Sent To

Notes

2006-05-27 00:00:00


	************PASSED/PROVISO**********


	SANITARY BUILDING DRAIN SHALL BE A
	MINIMUM OF 4 FT OFF THE FOOTER PER
	SECTION 307.4








	.

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2005-11-28			Cont ID
Sent By	kstevens			Date	2005-11-28	Time	17:11	Rev Time	0.00
Received By	kstevens			Date	2005-11-28	Time	17:11	Sent To

Notes

2005-11-28 00:00:00	DENIED
	REFERENCE: FBC-2001 PLUMBING

	1. SHTS P2.1.1, P-2.2.4, P-3.1.1, P-3.2
	AND P-3.2.4 WATER HAMMER ARRESTORS ARE
	REQUIRED AT THE WASH MACHINES OF ALL
	UNITS. PER SECTION 604.9. - ALL WATER
	HAMMER ARRESTORS SHALL BE LOCATED NEAR
	THE FIXTURES IN AN "EFFECTIVE RANGE",
	NOT IN THE CEILING AS SHOWN IN SOME
	CASES. PDI-WH 201 AND MANUF INSTALLATION
	INSTRUCTIONS.
	2. IF INDIVIDUAL METERS NO BACKFLOW
	DEVISE IS REQUIRED, BUT IF SINGLE METER
	AN RPZV BACKFLOW WILL BE REQUIRED ON THE
	WATER SERVICE. PLEASE CLARIFY. SECTION
	608.13.2.

	REVIEW BY KEN STEVENS
	(561) 805-6721
	FAX (561) 653-2692
	E-MAIL [email protected]

Review Stop	Z			ZONING
Rev No	1	Status	P	Date	2006-01-20			Cont ID
Sent By	mmclean			Date	2006-01-20	Time	17:34	Rev Time	0.00
Received By	mmclean			Date	2006-01-20	Time	17:34	Sent To

Notes

***NONE***