Plan Review Details - Permit 05091266
Plan Review Stops For Permit 05091266
Review Stop B BUILDING (STRUCTURAL)
Rev No 2 Status F Date 2006-03-06 Cont ID  
Sent By alange Date 2006-03-06 Time 11:02 Rev Time 2.00
Received By alange Date 2006-03-06 Time 10:49 Sent To  
Notes
2006-03-06 00:00:00DENIED
  
 1. 713.13 F.S.A NOTICE OF COMMENCEMENT
 SHALL BE RECORDED AT PALM BEACH COUNTY
 COURTHOUSE AND A COPY SUBMITTED TO THIS
 OFFICE BEFORE A PERMIT CAN BE ISSUED.
 BLANK FORMS ARE AVAILABLE FROM THIS
 OFFICE.
 NOTE: THE NOTICE OF COMMENCEMENT MUST BE
 RE-RECORDED IF THE DESCRIBED IMPROVEMENT
 OR CONSTRUCTION IS NOT COMMENCED WITHIN
 90 DAYS OF RECORDING.
  
 2.BEFORE A PERMIT TO CONSTRUCT, MAY BE
 ISSUED, IMPACT FEES MUST BE PAID TO PALM
 BEACH COUNTY. THE ACTUAL PERMIT
 SET OF PLANS MUST BE STAMPED BY THAT
 OFFICE, AND A COPY OF THE PAID RECEIPT
 ATTACHED TO THE PERMIT APPLICATION.
 PLEASE CALL (561)233-5025 FOR MORE
 INFORMATION.
  
 3.SUBMIT TWO COPIES OF ORIGONAL SIGNED
 AND SEALED SURVEYS.FS 472.025
  
 5.BASED ON SBCCI BUILDING VALUATION
 DATA THE PERMIT VALUATION HAS BE REVISED
 AS FOLLOWS:
 829AC SQ.FT. X $76.96 = $63,799
 771 SQ. FT. X $41.60 = $32,073
 REVISED TOTAL $95,872.00 ADDITIONAL
 PERMIT FEES ARE DUE.
  
 6.THE MINIMUM FOOTING DEPTH SHALL BE
 NO LESS THAN A 12" FOOTING FBC 1804.1.3
  
 7.SHOW HOW EXISTING BUILDING WILL
 COMPLY WITH FBC 3401.7.1.2.1 FOR SMOKE
 DETECTORS AND GFCI OUTLETS.
  
 8.PRODUCT APPROVALS SUBMITTED ARE
 INCOMPLETE.SUBMIT TWO COPIES OF
 PRODUCT APPROVALS WITH QUALITY ASSURANCE
 (MIAMI-DADE) FOR EXAMPLE WITH THE
 FOLLOWING STATE PRODUCT APPROVAL
 INFORMATION ATTACHED.
 PRODUCT APPROVALS SUBMITTED WITH
 PERMIT APPLICATION AFTER OCTOBER 1, 2003
 ARE REQUIRED TO COMPLY WITH THE FLORIDA
 PRODUCT APPROVAL SYSTEM. FOR INFORMATION
 PLEASE SEE THE STATE WEBSITE AT
 WWW.FLORIDABUILDING.ORG. PRODUCTS WITH
 STATEWIDE APPROVAL ARE REQUIRED TO BE
 SUBMITTED WITH A COVER SHEET THAT LISTS
 THE PRODUCT IDENTITY NUMBER FROM THE
 STATE. IF THE PRODUCT DOES NOT HAVE
 STATEWIDE APPROVAL, SUBMIT AN APPLICA-
 TION FOR LOCAL PRODUCT APPROVAL OR SITE
 SPECIFIC FORM PER RULE 9B-72. SEE
 ATTACHMENT. WWW.FLORIDABUILDING.ORG
  
 WHEN RESUBMITTING PLANS PLEASE INDICATE
 THE REVISION & REMOVE & REPLACE ANY
 PAGES AS NECESSARY. A TRANSMITTAL LETTER
 LISTING THE ORIGINAL REVIEW COMMENT NUM-
 BER, WITH A DESCRIPTION OF THE REVISION
 MADE, IDENTIFYING THE SHEET OR SPECIFICA
 TION PAGE WHERE THE CHANGES CAN BE FOUND
 WILL HELP TO EXPEDITE YOUR PERMIT. THANK
 YOU FOR YOUR ANTICIPATED COOPERATION.
  
 ART LANGE
 BUILDING PLANS EXAMINER
 805-6672
  
Review Stop B BUILDING (STRUCTURAL)
Rev No 1 Status F Date 2005-10-14 Cont ID  
Sent By alange Date 2005-10-14 Time 07:46 Rev Time 3.00
Received By alange Date 2005-10-14 Time 07:10 Sent To  
Notes
2005-10-14 00:00:00DENIED
  
 1. 713.13 F.S.A NOTICE OF COMMENCEMENT
 SHALL BE RECORDED AT PALM BEACH COUNTY
 COURTHOUSE AND A COPY SUBMITTED TO THIS
 OFFICE BEFORE A PERMIT CAN BE ISSUED.
 BLANK FORMS ARE AVAILABLE FROM THIS
 OFFICE.
 NOTE: THE NOTICE OF COMMENCEMENT MUST BE
 RE-RECORDED IF THE DESCRIBED IMPROVEMENT
 OR CONSTRUCTION IS NOT COMMENCED WITHIN
 90 DAYS OF RECORDING.
  
 2.BEFORE A PERMIT TO CONSTRUCT, MAY BE
 ISSUED, IMPACT FEES MUST BE PAID TO PALM
 BEACH COUNTY. THE ACTUAL PERMIT
 SET OF PLANS MUST BE STAMPED BY THAT
 OFFICE, AND A COPY OF THE PAID RECEIPT
 ATTACHED TO THE PERMIT APPLICATION.
 PLEASE CALL (561)233-5025 FOR MORE
 INFORMATION.
  
 3.SUBMIT TWO COPIES OF ORIGONAL SIGNED
 AND SEALED SURVEYS.FS 472.025
  
 4.SIGN OWNER/AGENT ON ENERGY CALCS.
  
 5.BASED ON SBCCI BUILDING VALUATION
 DATA THE PERMIT VALUATION HAS BE REVISED
 AS FOLLOWS:
 829AC SQ.FT. X $76.96 = $63,799
 771 SQ. FT. X $41.60 = $32,073
 REVISED TOTAL $95,872.00 ADDITIONAL
 PERMIT FEES ARE DUE.
  
 6.THE MINIMUM FOOTING DEPTH SHALL BE
 NO LESS THAN A 12" FOOTING FBC 1804.1.3
  
 7.SHOW HOW EXISTING BUILDING WILL
 COMPLY WITH FBC 3401.7.1.2.1 FOR SMOKE
 DETECTORS AND GFCI OUTLETS.
  
 8.PRODUCT APPROVALS SUBMITTED ARE
 INCOMPLETE.SUBMIT TWO COPIES OF
 PRODUCT APPROVALS WITH QUALITY ASSURANCE
 (MIAMI-DADE) FOR EXAMPLE WITH THE
 FOLLOWING STATE PRODUCT APPROVAL
 INFORMATION ATTACHED.
 PRODUCT APPROVALS SUBMITTED WITH
 PERMIT APPLICATION AFTER OCTOBER 1, 2003
 ARE REQUIRED TO COMPLY WITH THE FLORIDA
 PRODUCT APPROVAL SYSTEM. FOR INFORMATION
 PLEASE SEE THE STATE WEBSITE AT
 WWW.FLORIDABUILDING.ORG. PRODUCTS WITH
 STATEWIDE APPROVAL ARE REQUIRED TO BE
 SUBMITTED WITH A COVER SHEET THAT LISTS
 THE PRODUCT IDENTITY NUMBER FROM THE
 STATE. IF THE PRODUCT DOES NOT HAVE
 STATEWIDE APPROVAL, SUBMIT AN APPLICA-
 TION FOR LOCAL PRODUCT APPROVAL OR SITE
 SPECIFIC FORM PER RULE 9B-72. SEE
 ATTACHMENT. WWW.FLORIDABUILDING.ORG
  
 WHEN RESUBMITTING PLANS PLEASE INDICATE
 THE REVISION & REMOVE & REPLACE ANY
 PAGES AS NECESSARY. A TRANSMITTAL LETTER
 LISTING THE ORIGINAL REVIEW COMMENT NUM-
 BER, WITH A DESCRIPTION OF THE REVISION
 MADE, IDENTIFYING THE SHEET OR SPECIFICA
 TION PAGE WHERE THE CHANGES CAN BE FOUND
 WILL HELP TO EXPEDITE YOUR PERMIT. THANK
 YOU FOR YOUR ANTICIPATED COOPERATION.
  
 ART LANGE
 BUILDING PLANS EXAMINER
 805-6672
  
Review Stop E ELECTRICAL
Rev No 2 Status F Date 2006-03-01 Cont ID  
Sent By btrobaug Date 2006-03-01 Time 10:40 Rev Time 0.75
Received By btrobaug Date 2006-02-28 Time 17:03 Sent To M
Notes
2006-02-28 00:00:00 
 PLEASE MAKE THE FOLLOWING CORRECTIONS
 FOR CODE COMPLIANCE AND RESUBMIT FOR
 REVIEW.
  
 1} INDICATE THE CONDUIT AND CONDUCTOR
 SIZES FOR THE RISER. ALSO AIC RATING OF
 THE EQUIPMENT PER 110.9 & 10.
  
 2} THE BREAKER AND WIRE SIZE IS
 INCORRECT FOR THE LOAD INDICATED ON THE
 SCHEDULE. CIRCUIT #2-4 AHU.
  
 3} PLEASE NOTE THE OCP (60) IS TOO LARGE
 FOR THE CONDUCTOR SIZE (#8) FOR THE
 RANGE.
  
 4} CIRCUIT #28 , MASTER BATH, MUST
 COMPLY WITH 210.11(C)(3).
  
 5} PLEASE SEE NOTE #3 REGARDING KITCHEN
 GFI SHOULD INDICATE ALL COUNTERTOP
 RECEPTACLE PER 210.8(A)(6).
  
 6} THERE ARE RECEPTACLES LOCATED
 THROUGHOUT THE EXISTING HOUSE, BUT THEY
 DO NOT SHOW CODE COMPLIANCE WITH ARTICLE
 210.52. INDICATE IF THESE ARE NEW OR
 EXISTING. IF PART OF THIS APPLICATION
 SHOW EXISTING DEVICES AS WELL SO THAT
 COMPLIANCE MAY BE DETERMINED.
  
 7} THE ENGINEERING FIRM ADVERTISING AS A
 CORPORATION ON THE TITLE BLOCK, MUST
 INCLUDE THEIR REQUIRED CERTIFICATE OF
 AUTHORIZATION NUMBER ON THE TITLE BLOCK
 PER 61G15-23.002, FACODE.
  
 IF THERE ARE ANY QUESTIONS PLEASE CALL.
  
 BILL TROBAUGH
 ELECTRICAL PLAN REVIEW
 561/805-6718
 [email protected]
 FAX/:561/659-8026
  
Review Stop E ELECTRICAL
Rev No 1 Status F Date 2005-10-07 Cont ID  
Sent By btrobaug Date 2005-10-07 Time 16:34 Rev Time 0.50
Received By btrobaug Date 2005-10-06 Time 12:32 Sent To M
Notes
2005-10-07 00:00:00 
 PLEASE MAKE THE FOLLOWING CORRECTIONS
 FOR CODE COMPLIANCE AND RESUBMIT FOR
 REVIEW.
  
 1} INDICATE THE CONDUIT AND CONDUCTOR
 SIZES FOR THE RISER. ALSO AIC RATING OF
 THE EQUIPMENT PER 110.9 & 10.
  
 2} THERE MUST BE A DISCONNECT PER
 230.70(A)(1), PREFERABLY NEXT TO THE
 METER.
  
 3} PLEASE NOTE THE OCP (60) IS TOO LARGE
 FOR THE CONDUCTOR SIZE (#8) FOR THE
 RANGE.
  
 4} CIRCUIT # 27, MASTER BATH, MUST
 COMPLY WITH 210.11(C)(3).
  
 5} THE RECEPTACLES IN THE GARAGE MUST BE
 GFI PROTECTED PER 210.8(A)(2).
  
 6} THERE ARE RECEPTACLES LOCATED
 THROUGHOUT THE EXISTING HOUSE, BUT THEY
 DO NOT SHOW CODE COMPLIANCE WITH ARTICLE
 210.52. INDICATE IF THESE ARE NEW OR
 EXISTING. IF PART OF THIS APPLICATION
 SHOW EXISTING DEVICES AS WELL SO THAT
 COMPLIANCE MAY BE DETERMINED.
  
 7} THE ENGINEERING FIRM ADVERTISING AS A
 CORPORATION ON THE TITLE BLOCK, MUST
 INCLUDE THEIR REQUIRED CERTIFICATE OF
 AUTHORIZATION NUMBER ON THE TITLE BLOCK
 PER 61G15-23.002, FACODES.
  
 IF THERE ARE ANY QUESTIONS PLEASE CALL.
  
 BILL TROBAUGH
 ELECTRICAL PLAN REVIEW
 561/805-6718
 [email protected]
 FAX/:561/659-8026
  
  
Review Stop I INCOMING/PROCESSING
Rev No 4 Status N Date 2006-02-25 Cont ID  
Sent By adarroug Date 2006-02-25 Time 11:42 Rev Time 0.00
Received By adarroug Date 2006-02-25 Time 11:42 Sent To E
Notes
2006-02-25 00:00:00TO "BTROBAUG" DESK/RESUB
Review Stop I INCOMING/PROCESSING
Rev No 3 Status N Date 2006-02-17 Cont ID  
Sent By adarroug Date 2006-02-17 Time 16:11 Rev Time 0.00
Received By adarroug Date 2006-02-17 Time 16:11 Sent To Z
Notes
2006-02-17 00:00:00TO "Z" BOX/RESUB
Review Stop I INCOMING/PROCESSING
Rev No 2 Status N Date 2005-10-05 Cont ID  
Sent By adarroug Date 2005-10-05 Time 16:44 Rev Time 0.00
Received By adarroug Date 2005-10-05 Time 16:44 Sent To E
Notes
2005-10-05 00:00:00TO "E" BOX
Review Stop I INCOMING/PROCESSING
Rev No 1 Status N Date 2005-10-14 Cont ID  
Sent By mmclean Date 2005-10-14 Time 07:46 Rev Time 0.00
Received By alange Date 2005-09-27 Time 16:47 Sent To  
Notes
2005-09-27 00:00:00TO "Z" BOX
Review Stop M MECHANICAL (A/C)
Rev No 2 Status F Date 2006-03-01 Cont ID  
Sent By tgordon Date 2006-03-01 Time 13:37 Rev Time 0.45
Received By tgordon Date 2006-03-01 Time 13:37 Sent To B
Notes
2006-03-01 00:00:00*** DENIED ***
 1) ENERGY CALCULATIONS ARE CALLING FOR
 AN ELECTRIC HEAT PUMP UNIT, MECHANICAL
 PLANS ARE CALLING FOR A 5 KW ELECTRIC
 RESISTANCE HEATER, AND THE ELECTRICAL
 PLANS ARE CALLING FOR A 10 KW ELECTRIC
 RESISTANCE HEATER. PLEASE CORRECT SO ALL
 COINCIDE.
  
 2) ENERGY CALCULATIONS ARE CALLING FOR A
 9.80 SEER A/C SYSTEM (THE MINIMUM
 ALLOWABLE IS 10 SEER), THE MECHANICAL
 PLANS EQUIPMENT LIST IS CALLING FOR A 18
 SEER. THE TWO MUST COINCIDE PLEASE
 CORRECT.
  
 3) NEED TO SHOW ON MECH. PLANS THE
 RETURN AIR GRILL SIZE (A 5 TON SYSTEM
 REQUIRES ABOUGHT 725 SQUARE INCHES).
  
 4) CHECK WITH THE MANUFACTURE'S
 SPECIFICATION'S A 7/8 SUCTION LINE MAY
 BE TO SMALL FOR A 5 TON SYSTEM, CORRECT
 IF NECESSARY.
  
 5) THE MECHANICAL PLANS NEED THE
 ENGINEER'S SEAL ON THEM, PER F.S.
 61G1-16.002 .
  
 MECHANICAL PLAN REVIEW BY;
 TOM GORDON (561) 805-6729.
Review Stop M MECHANICAL (A/C)
Rev No 1 Status F Date 2005-10-11 Cont ID  
Sent By tgordon Date 2005-10-11 Time 14:33 Rev Time 0.30
Received By tgordon Date 2005-10-11 Time 14:33 Sent To P
Notes
2005-10-11 00:00:00*** DENIED ***
 1) SUPPLY AIR DUCT FROM A.H.U. TO MIXING
 BOX NOT SIZED.
 2) NO VISIBLE MEANS OF RETURN AIR FROM
 FAMILY ROOM TO A.H.U..
 3) DRYER VENT CAN NOT DISCHARGE AT
 CONDENSER UNIT.
 4) PLANS DO NOT STATE IF A/C EQUIPMENT
 IS NEW OR EXISTING.
 IF YOU HAVE ANY QUESTIONS PLEASE CALL
 TOM GORDON 805-6729 OR PATTY KRAUSS
 805-6719.
Review Stop P PLUMBING
Rev No 1 Status N Date 2005-10-12 Cont ID  
Sent By jleech Date 2005-10-12 Time 15:06 Rev Time 0.25
Received By jleech Date 2005-10-12 Time 15:05 Sent To B
Notes
2005-10-12 00:00:00NOT ENOUGH INFORMATION TO DO A PLUMBING
 PLAN REVIEW. IS THE WASHING MACHINE A
 NEW ADDITION OR MOVED FROM ANOTHER
 LOCATION. WASHER IS ON BLOCK WALL HOW
 WILL IT BE PIPED. VENT REQUIRED SHOW HOW
 W/M WILL TIE INTO SEWER SYSTEM AND WERE
 CLEANOUTS WILL BE LOCATED.
Review Stop Z ZONING
Rev No 2 Status P Date 2006-02-24 Cont ID  
Sent By mmclean Date 2006-02-24 Time 17:32 Rev Time 0.00
Received By mmclean Date 2006-02-24 Time 17:31 Sent To I
Notes
2006-02-24 00:00:00NOTE: THE PROPOSED ADDITION MUST MEET
 THE FRONT SETBACK OF 25FT ON PASEO DE
 NAVARRA.
 NOTE: THE PROPOSED PORTICO MUST BE
 12.5FT ON THE SIDE.
 NOTE: THE A/C MUST SIT BACK 25FT WITHIN
 THE FRONT SETBACK.
Review Stop Z ZONING
Rev No 1 Status P Date 2005-10-04 Cont ID  
Sent By mmclean Date 2005-10-04 Time 16:07 Rev Time 0.00
Received By mmclean Date 2005-10-04 Time 16:07 Sent To I
Notes
2005-10-04 00:00:00THE PROPOSED ADDITION MUST MEET THE
 FRONT SETBACK OF 25FT PASEO DE NAVARRA.
 THE PROPOSED PORTICO MUST BE 12.5FT ON
 THE SIDE.


Account Summary | Usage Policy | Privacy Policy
Copyright © 2005 – 2014, SunGard Pentamation, Inc & City of West Palm Beach, FL – All Rights Reserved