City of West Palm Beach eGovPlus

Plan Review Details - Permit 00100051

Plan Review Stops For Permit 00100051

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	2	Status	F	Date	2001-02-09			Cont ID
Sent By	hpiskura			Date	2001-02-09	Time	07:14	Rev Time	0.00
Received By	hpiskura			Date	2001-02-05	Time	11:26	Sent To

Notes

2001-02-09 00:00:00	SECOND PAID PLAN REVIEW.
	1.THE CODE ANALYSIS ON SHEET G1.01 IS
	INCORRECT.TYPE II CONSTRUCTION BY ITS
	DEFINITION IS PROTECTED.SEE SBC 604.
	2.THE STATED FIRE RATINGS ARE INCORRECT.
	SEE SBC TABLE 600. THE STATED HEIGHT
	AND AREA ARE INCORRECT.SEE SBC TABLE
	500.
	3. THE GLASS DOOR BETWEEN THE LOBBY AND
	THE GARAGE IS REQUIRED TO BE FIRE RATED.
	A ROLLING SHUTTER SYSTEM IS NOT AN
	ACCEPTABLE SUBSTITUTE FOR A MEANS OF
	EGRESS.SEE SBC 1012.4 #5 AND SBC
	1012.1.
	4. SHEET A27.6DESIGNATE THE SPECIFIC
	SIZING OF THE ELEVATOR SHAFT VENT.SEE
	SBC 3003.6 AND SBC 3001.1.
	5.SPECIFIC CONSTRUCTION DETIALS ARE
	NECESSARY FOR THE SUSPENDED STUCCO
	CEILING AND THE SUSPENDED FRAMING SHOWN
	ON SHEETS A6.01 AND A6.22 RESPECTIVELY.
	SEE SBC 104.2.1.
	6.THE STATEMENT ON SHEET A75.1
	"GLAZING SYSTEM TO MEET LOCAL CODE" IS
	NOT AN ACCEPTABLE SUBSTITUTE FOR
	SPECIFIC DESIGN INFORMATION.SEE THE
	ATTACHED POLICY AND PROCEDURE STATEMENT.
	7.THE STRUCTURAL SHEET S1.01 SHOWS
	OPENINGS ON THE SOUTH ELEVATION THAT
	ARE NOT ON THE ARCHITECTURAL PLANS.
	THE #2 STAIRS HAVE NOT BEEN REVISED ON
	THE STRUCTURAL PLANS.
	8.SHEET S7.01 DESIGN PARAMETERS CITE A
	BUILDING LESS THAN 60' IN HEIGHT.THIS
	BUILDING IS MORE TAHN 60' IN HEIGHT.
	PLEASE REVISE THE DESIGN CRITERIA
	ACCORDING AND DEMOMSTRATE THE CHANGES.
	9.SHEET A1.01.WHAT IS THE MEANING OF
	THE STATEMENT "DELUGE ENTRY SYSTEM
	W/SPRINKLER HEAD ON EACH SIDE @ 4'
	O.C."?
	10.THE ATRIUM.HOW DOES THE 5600 CFM
	FAN PROVIDE AN EXHAUST CAPACITY OF
	40,000 CFM AS REQUIRED BY SBC 414.4?
	WHERE DOES THE MAKEUP AIR COME FROM?
	HOW IS THE OTHER SPACE VENTING
	REQUIREMENT OF SBC 412.5 ACCOMPLISHED?
	11.SHEET AC1.O1.PLEASE PROVIDE
	DIMENSIONS ON THE SITE PLAN TO LOCATE
	THE BUILDING ON THE PROPERTY.
	12.SHEET A5.01.THE NOTE SAYS "OPEN
	AREA CALCULATED BASED ON SBC 411.3.2."
	WHICH METHOD WAS USED?! OR 2?THE
	NOTES "51% OPEN" IMPLIES METHOD 1 WHICH
	REQUIRES OPEN AREA FOR THE FULL LENGTH
	OF THE SIDE.THE PORTION BETWEEN GRID
	LINES C AND E ON THE REAR ELEVATION AND
	3 AND 4 ON THE RIGHT ELEVATION DO NOT
	APPEAR TO COMPLY WITH THIS.PLEASE
	PROVIDE INFORMATION SHOWING HOW THIS
	AREA OF THE CODE WILL BE COMPLIED WITH.
	SEE ALSO THE NOTES ON THE FIRST REVIEW
	COMMENTS RE IMPACT FEES, THRESHOLD
	BUILDING, ZONING, ETC.

	HAROLD PISKURA
	(561) 659-8096 X 8219

Review Stop	B			BUILDING (STRUCTURAL)
Rev No	1	Status	F	Date	2000-11-08			Cont ID
Sent By	hpiskura			Date	2000-11-08	Time	10:53	Rev Time	0.00
Received By	hpiskura			Date	2000-11-03	Time	14:42	Sent To

Notes

2001-01-08 00:00:00

LETTER W/ APPLICATION

Review Stop	E			ELECTRICAL
Rev No	2	Status	F	Date	2001-02-14			Cont ID
Sent By	dpalmer			Date	2001-02-14	Time	19:12	Rev Time	0.00
Received By	dpalmer			Date	2001-02-14	Time	19:12	Sent To

Notes

2001-02-14 00:00:00	****************UNSAT *************

	1)NOTE: PLEASE SUBMIT A LARGE SCALE
	DETAIL FOR FIRE PUMP/ AND EQUIPMENT
	LOCATION.
	2)NOTE: PLEASE SUBMIT LOAD CALCULATIONS
	PER 220 AND 215.

	3)NOTE: PLEASE NOTE INLINE DISCONNECTS
	REQ`D FROM GENERATOR TO ATS`S.
	225-31/225-32 AND 230-72 FOR GROUPING
	OF DISC.

	4)NOTE: PLEASE SHOW SIZE OF CONDUCTORS
	AND CONDUITS FROM ATS`S/DISC TO GEN.

	5)NOTE:PLEASE SHOW GROUNDING ELECTRODE
	SYSTE. PLANS SAY TO SEE DETAIL?

	6)NOTE: PLEASE PROVIDE CLARIFICATION FOR
	695-4-B-1. AND OCP FOR SIZING OF FIRE
	PUMP. AT 125%

	7)NOTE: PLEASE PROVIDE PANEL SCHEDULES
	SHOWN ON RISER DIAGRAMS IN BOTHSETS OF
	PLANS.

	JUST NOTE THAT SHUNT TRIPS ARE
	NOT RATED FOR MEANS OF DISCONNECTS PER
	230-76 AND 230-79


	PLEASE SUBMIT CLARIFICATION ON THE ABOVE
	INFORMATION FOR REVEIW. IF THERE ARE
	ANY QUESTIONS PLEASE CALL.

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW
	561-659-8096 EXT 8372

Review Stop	E			ELECTRICAL
Rev No	1	Status	F	Date	2000-11-02			Cont ID
Sent By	dpalmer			Date	2000-11-02	Time	10:05	Rev Time	0.00
Received By	dpalmer			Date	2000-11-02	Time	10:05	Sent To

Notes

2001-01-08 00:00:00	************** UNSAT ***************

	1)NOTE: PLAN REVIEW WAS SUBMITTED FOR
	A 3 STORY OFFICE/MEDICAL BLDG AND GARAGE
	BUT PLANS ONLY REFLECT GARAGE?????

	2)NOTE: PLEASE SUBMIT LOAD CALCULATIONS
	, GROUNDING ELECTRODE SYSTEM. ETC.
	215-5

	3)NOTE: PLEASE CLARIFY LOADS SHOWN ON
	PANEL SCHEDULES. ONE SHOWS CKT KW THE
	OTHER PHASE KW .?

	PLEASE SUBMIT THE ABOVE INFORMATION
	FOR REVIEW. IF THERE ARE ANY QUESTIONS
	PLEASE CALL

	DEWEY PALMER
	ELECTRICAL PLAN REVIEW
	561-659-8096 EXT 8372

Review Stop	ENG			ENGINEERING CSD
Rev No	1	Status	N	Date	2000-11-02			Cont ID
Sent By	mgonzale			Date	2000-11-02	Time	15:43	Rev Time	0.50
Received By	mgonzale			Date		Time		Sent To

Notes

2001-01-08 00:00:00

PLANS DO NOT INCLUDED CIVIL DRAWINGS

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	2	Status	F	Date	2001-02-07			Cont ID
Sent By	mcarsill			Date	2001-02-07	Time	13:57	Rev Time	0.00
Received By	mcarsill			Date	2001-02-07	Time	13:56	Sent To

Notes

2001-02-07 00:00:00	1) CODE ANALYSIS BOX ON PAGE G1.01
	INDICATES A ONE HOUR FIRE SEPARATION
	BETWEEN THE OFFICE BUILDING AND PARKING
	STRUCTURE. PLAN REVIEW COMMENTS
	INDICATES A TWO HOUR FIRE SEPARATION.
	PLEASE CORRELATE INFORMATION.
	2) PLEASE INDICATE LOCATION OF FIRE
	DEPARTMENT CONNECTIONS. THESE DEVICES
	ARE TO BE LOCATED NO FARTHER 150 FEET
	FROM FIRE HYDRANTS.
	3) ONLY TWO EXITING FIRE HYDRANTS COULD
	BE LOCATED ON THE SURVEY. ADDITIONAL
	FIRE HYDRANTS APPEAR TO BE NEEDED. ALSO
	BE ADVISED THAT THE UTILITIES DEPARTMENT
	ARE TO REVIEW THE FIRE SPRINKLER PLANS
	AND UNDERGROUND UTILITIES PLANNED FOR
	THE SITE.
	4) PLEASE PROVIDE PRODUCT APPROVALS FOR
	TWO HOUR CONCEALED ROLL-UP SHUTTER AT
	DOOR ON PAGE A1.01.
	5) SEPARATE PERMIT REQUIRED FOR MEDICAL
	GAS SYSTEMS PLANNED FOR THE BUILDING.
	6) PLEASE EXPLAIN DELUGE FIRE SPRINKLER
	SYSTEM PLANNED FOR THE ENTRY SYSTEM ON
	PAGE A1.01.
	7) PLEASE PROVIDE MORE DETAILS ON
	GENERATOR.
	8) CABLE GUARDS TO COMPLY WITH LIFE
	SAFETY CODE REQUIREMENTS.
	9) THE ATRIUM TO COMPLY WITH NFPA 101,
	THE LIFE SAFETY CODE, 1985 EDITION,
	SECTION 6-2.2.3.5. PLEASE SHOW
	COMPLIANCE WITH ALL SECTIONS OF THIS
	CODE. PLEASE PROVIDE TETSING CRITERIA
	AND EXPECTED PERFORMANCE FOR THE
	ATRIUM.

	CAPTAIN MIKE CARSILLO
	659-8096,EXT.8497
	835-2910

Review Stop	FIRE			FIRE DEPARTMENT
Rev No	1	Status	F	Date	2000-10-06			Cont ID
Sent By	mcarsill			Date	2000-10-06	Time	13:29	Rev Time	0.00
Received By	mcarsill			Date	2000-10-06	Time	13:29	Sent To

Notes

2001-01-08 00:00:00	1) NO FIRE HYDRANTS SHOWN ON SITE PLAN.
	PLEASE INDICATE FIRE HYDRANT LOCATIONS
	ON SITE PLAN.
	2) BUILDING ADDRESS NOT SHOWN ON
	ELEVATION DRAWINGS. BUILDING ADDRESS
	TO BE INSTALLED IN ACCORDANCE WITH CITY
	CODE REQUIREMENTS.
	3) AN APPLICATION FOR A KNOX-BOX CAN
	BE RECEIVED FROM THE FIRE RESCUE
	DEPARTMENT.
	4) ELEVATORS TO COMPLY WITH ANSI A.17.1
	AND THE UNIFORM FIRE SAFETY RULES AND
	STANDARDS 4A-47. ELEVATORS ARE TO HAVE
	BOTH PHASE ONE AND PHASE TWO RECALL
	FUNCTIONS.
	5) NO FIRE SPRINKLER SYSTEM DRAWINGS
	OR HYDRAULIC CALCULATIONS PROVIDED FOR
	OFFICE BUILDING.
	6) NO OCCUPANT LOAD CALCULATIONS
	PROVIDED FOR LEASE SPACES.
	7) ADDITIONAL EXIT SIGNAGE IS NEEDED TO
	DIRECT PERSONS TO EXIT DOOR LOCATIONS.
	8) MECHANICAL ROOM DOORS (301) WHEN
	OPENED BLOCK EXIT DOOR.
	9) STAIRS TO COMPLY WITH NEW STAIRS,
	NFPA 101, THE LIFE SAFETY CODE, 1985
	EDITION.
	10) HANDRAILS AND GUARDS TO COMPLY WITH
	NFPA 101, THE LIFE SAFETY CODE, 1985
	EDITION.
	11) PLEASE INDICATE FIRE PROTECTION
	DETAILS FOR TOWER BETWEEN PARKING GARAGE
	AND OFFICE TOWER.
	12) PLEASE PROVIDE INTERIOR FINISH
	INFORMATION FOR EXITS AND OTHER AREAS OF
	THE OFFICE BUILDING.

	PARKING GARAGE
	1) NO FIRE SPRINKLER DRAWINGS OR
	HYDRAULIC CALCULATIONS PROVIDED WITH
	PLANS.
	2) NO FIRE STANDPIPE SYSTEM DRAWINGS
	INCLUDED WITH PLANS.
	3) PARKING GARAGE TO COMPLY WITH NFPA
	88, THE STANDARD FOR PARKING STRUCTURES
	AND NFPA 101, THE LIFE SAFETY CODE,
	1985 EDITION, SECTION 29.8, PARKING
	GARAGES.
	4) THE FIRE SPRINKLER AND FIRE ALARM
	SYSTEMS IN BOTH BUILDINGS ARE TO BE
	MONITORED BY A LICENSED UL LISTED
	CENTRAL STATION APPROVED BY THE FIRE
	RESCUE DEPARTMENT.
	5) PLEASE PROVIDE MORE DETAILS ON STEEL
	CABLE GUARDRAIL SYSTEM.
	6) CLEARLY IDENTIFY THE REQUIRED TWO
	MEANS OF EGRESS FROM EVERY LEVEL OF
	THE PARKING GARAGE.
	7) PROVIDE OCCUPANT LOAD CALCULATIONS
	FOR THE PARKING GARAGE.
	8) PLEASE PROVIDE INTERIOR FINISH
	INFORMATION FOR THE PARKING GARAGE.

Review Stop	M			MECHANICAL (A/C)
Rev No	2	Status	F	Date	2001-02-07			Cont ID
Sent By	ndenmark			Date	2001-02-07	Time	12:50	Rev Time	2.00
Received By	ndenmark			Date	2001-02-07	Time	12:47	Sent To

Notes

2001-02-07 00:00:00	**********DENIED********************
	1. PLAN SHOWS 3 STORY ATRIUM. SHOW
	COMPLIANCE WITH 1997 SBC 414.4.2 "IN
	ATRIUMS 55FT OR LESS IN HEIGHT WITH A
	VOLUME OF 600,000 CU. FT. OR LESS, A
	SMOKE EXHAUST SYSTEM SHALL BE LOCATED
	AT THE CEILING OF THE ATRIUM. SUCH
	SYSTEMS SHALL EXHAUST 40,000 CFM.
	414.4.3 REQUIRES SUPPLY AIR INLETS
	PROVIDING 75% OF THE EXHAUST. THE
	INLETS MAY BE LOCATED AT THE LOWEST
	LEVEL OF THE ATRIUM.
	2. 414.8 REQUIRES SMOKE CONTROL IN ANY
	OCCUPIED SPACE THAT DOES NOT DIRECTLY
	OPEN INTO THE ATRIUM SHALL BE DESIGNED
	TO PROVIDE NATURAL OR MECHANICAL
	VENTILATION IN ACCORDANCE WITH SMC
	412.5. SHOW COMPLIANCE WITH THIS
	SECTION.
	3. PROVIDE SEQUENCE OF OPERATION FOR
	ATRRIUM SMOKE CONTROL SYSTEM.
	4. ALL SECTIONS OF 1997 SBC 414 THAT
	APPLY TO THIS BUILDING NEED TO HAVE
	COMPLIANCE INDICATED ON THE PLAN FOR
	REVIEW PURPOSES.
	5. PROVIDE DETAIL ON EXHAUST SYSTEM FOR
	THE ATRIUM (EF#5) INCLUDING SHAFT
	PROTECTION AND CFM TO COMPLY WITH NOTE
	1 ABOVE. NOTE PLAN SHOWS FIRE DAMPER AT
	OUTLET .ON M-1.03. IF CODE REQUIRES A
	FIRE DAMPER IN THIS LOCATION IT SHALL
	BE ABLE TO BE OVERRIDDEN FROM A FIRE
	PANEL TO ALLOW THE SMOKE CONTROL SYSTEM
	TO FUNCTION AS REQUIRED BY THE BUILDING
	CODE. PLEASE INDICATE COMPLIANCE WITH
	THIS IN THE SEQUENCE OF OPERATION.
	6. PROVIDE DETAIL FOR MECHANICAL ROOMS
	SHOWING MAUFACTURES REQUIRED CLEARANCE
	AREAS FOR COIL PULL, SERVICE ACCESS,
	ETC. 1997 SMC 304.2 REQUIRES
	ACCESSIBILITY OF ALL EQUIPMENT WITH
	RESPECT TO BUILDING CONSTRUCTION. THE
	NATIONAL ELECTRIC CODE HAS MINIMUM
	REQUIREMENTS WHICH WILL HAVE TO BE
	COMPLIED TO FOR THIS EQUIPMENT. CLEARLY
	SHOW THESE DEDICATED AREAS IN THE
	DETAIL.
	7. PROVIDE INFORMATION ON CONDENSATE
	DRAIN SYSTEM FOR AIR HANDLER EQUIPMENT
	AND OVERFLOW PER 1997 SMC 304.8
	8. PROVIDE INFORMATION FOR VENTILATION
	IN THE MECHANICAL AND MEDICAL GAS
	STORAGEROOMS ON THE FIRST LEVEL PARKING
	GARAGE.

Review Stop	M			MECHANICAL (A/C)
Rev No	1	Status	F	Date	2000-11-01			Cont ID
Sent By	ndenmark			Date	2000-10-31	Time	12:02	Rev Time	5.00
Received By	ndenmark			Date	2000-10-31	Time	12:02	Sent To

Notes

2001-01-08 00:00:00	*********DENIED*********************
	1.MECHANICAL DRAWINGS ARE REQUIRED TO BE
	SIGNED AND SEALED BY THE ENGINEER OF
	RECORD. SUBMIT SIGNED ANS SEALED PLANS.

	2.SHAFTLOCATED BETWEEN ELEVATOR LOBBY
	AND STAIRS HAS SEVERAL DUCTS EXITING.
	ALL DUCTS PENETRATING SHAFT SHALL BE

	3.1997 SMC 610.1.2 REQUIRES FIRE DAMPERS
	TO BE LOCATED WHERE DUCTS PENETRATE ALL
	RATED WALLS AND PARTITIONS.
	SMC 610.6 REQUIRES LOCATION AND INSTALL-
	ATION DETAILS TO BE SHOWN AND PROPERLY
	IDENTIFIED ON BUILDINGS BY THE DESIGNER.

	4. MECH DUCTS ARE SHOWN RUNNING THROUGH
	ELECTRIC ROOM. NEC DOES NOT PERMIT

	5. IDENTIFY AHU CORE AS SHOWN ON M2.01
	LOCATION.
	6. LOCAL AMENDMENTS REQUIRE A MINIMUM OF
	18" CLEARANCE BETWEEN ROOF SURFACE AND
	BOTTOM OF SUPPORT STRUCTURE OF EQUIPMENT
	STAND.

	7. PROVIDE ELEVATION SHOWING SHAFT AND
	DUCT DETAIL INCLUDING LOCATION OF FIRE
	DAMPERS.

	8. PROVIDE OUTSIDE AIR SCHEDULE PER
	ASHRAE 62-89

	9. PROVIDE AIR BALANCE SCHEDULE SHOWING
	COMPLIANCE WITH 1997 SMC 501.2

Review Stop	P		PLUMBING
Rev No	3	Status	Date		Cont ID
Sent By			Date	Time	Rev Time	0.00
Received By			Date	Time	Sent To

Notes

***NONE***

Review Stop	P			PLUMBING
Rev No	2	Status	F	Date	2001-02-26			Cont ID
Sent By	jleech			Date	2001-02-26	Time	13:53	Rev Time	6.00
Received By	jleech			Date	2001-02-26	Time	13:53	Sent To

Notes

2001-02-26 00:00:00	DENIED;

	1.BATHROOM FACILITIES ARE REQUIRED ON
	EACH FLOOR OF SHELL. 94 SPC SEC. 402
	(PUBLIC USE) AND 407.1.4.
	2.AHCA SHOULD BE INVALVED. THIS IS A
	MEDICAL BUILDING.
	3.P3.01 WASTE AND VENT RISER. MAIN VENT
	NOT TIED BACK INTO SANITARY DRAINAGE
	SYSTEM.
	4.FLOOR SINK REQUIRED FOR W/H ON 3RD FL.
	NOT SHOWN ON SANITARY RISER DIAGRAM.
	5.P3.01 FLOOR DRAINS REQUIRED IN 3RD FL.
	BATHROOMS.
	6.FLOOR DRAINS IN BATHROOMS MUST HAVE
	TRAP PRIMERS. TRAP PRIMERS ARE LISTED
	IN PROJECT MANUAL BUT NOT SHOWN ON
	PLANS.
	7.A2.01 2-M.TLC304 AND 303.DOOR SWING
	INFRINGES ON LAVITORYS CLEAR FLOOR
	SPACE. DOORS SHOULD SWING OUT. M AND K
	ALSO INFRINGES ON LAVITORY CLF. FACBC
	4.19.3 AND 4.17.5.
	8.FLUSH VALVES SHALL BE MOUNTED ON THE
	WIDE SIDE OF THE TOILET AREA. FACBC
	4.16.5
	9.P0.01 DELETE GAS CONNECTION DETAIL IF
	NO FUEL GAS WILL BE USED.
	10.P0.01 WATER HEATER DETAIL, CHANGE
	FLOOR DRAIN NOTATIONTO FLOOR SINK.
	11.IF NO MEDICAL GAS WILL BE INSTALLED
	IN SHELL ADD A NOTE TO THAT AFFECT.
	12.P3.01 SHOW LOCATION AND SIZE OF AIR-
	CHAMBER IN ACCORDANCE WITH SPC 607.8.
	2.
	13.FOR ROOF DRAIN CALCULATIONS FOLLOW 94
	SPC CHAPTER 11.ROOF AREA INCLUDES THE
	ROOF AND 1/2 OF THE PARAPET WALL,
	ALSO ROOF OVER MECHANICAL ROOM.PER.
	FIG.1108.4 RAIN IN THIS AREA IS BAST
	ON 4.5 INCHS OF RAIN PER HOUR.
	14.SHOW CHILL WATER SUPPLY LINE ON WATER
	RISER AND LOCATION IN MECH. ROOM.
	15.PARKING GARAGE. SHOW SQ. FT. AREA FOR
	EACH FLOOR DRAIN. SHOW ACCUMULATION
	OF AREA AS PIPES GO FROM 6TH FLOOR TO
	UNDERGROUND. A RISER DIAGRAM WOULD BE
	A GOOD WAY TO ACCOMPLISH THIS.
	16.NO WATER SHOWN IN GARAGE AREA. IS
	THIS TRUE?
	PLUMBING PLAN REVIEW BY;
	JOHN LEECH
	659-8096 EXT.8377

Review Stop	P			PLUMBING
Rev No	1	Status	F	Date	2000-10-16			Cont ID
Sent By	tlarge			Date	2000-10-16	Time	09:00	Rev Time	6.00
Received By	tlarge			Date	2000-10-15	Time	11:57	Sent To

Notes

2001-01-08 00:00:00	1)SUBMIT COPY OF AHCA APPROVAL.SPC SEC.
	101.4.7.

	2)JOB SPEC.15430-PART 3.2-CALCULATED AIR
	CHAMBERS(IF USED)SHALL COMPLY W/STANDARD
	PDI-WH201

	3)JOB SPEC.15440-PART 1.1-PLUMBING
	FIXTURES SHALL BE WATER CONSERVATION
	TYPE PER SPC 406.

	4)SUBMIT OCCUPANT LOAD PER TABLE 407 OF
	THE SPC.SEE SPC SEC.407.1.3.FOR ALLOWED
	DEDUCTIBLE AREAS.COMPLY W/SPC TABLE 407
	FOR MIN.FIXTURE REQS.

	5)LAVATORIESARE REQD.INTHE
	HANDICAP STALLS PER FACBC SEC.4.17.3.
	SIZE OF STALL AND REQD.CLEAR FLOOR SPACE
	OF FIXTURES SHALL COMPLY W/FACBC SECS.
	4.17,FIG.30,4.19 AND FIG.32.

	6)SUBMIT SANITARY AND WATER ISOMETRICS
	FOR ALL PLUMBING WORK FOR THE SHELL
	BUILDING AND THE GARAGE.COUNTYWIDE
	AMENDMENTS TO SPC SEC.104.2.1.

	7)SUBMIT COMPLETE STORM RISER DIAGRAM
	FOR REVIEW.INCLUDE REQS.FOR SECONDARY
	DRAINAGE.COMPLY W/SPC SECS.1108.1 THRU
	1108.4,1109 AND APPENDIX "A".

	8)SUBMIT ROOF PLAN SHOWING ROOF DRAINS
	AND SHOW SQUARE FOOTAGE DRAINED BY EACH
	ROOF DRAIN.COMPLY W/SPC TABLES 1108.1,
	1108.2.INCLUDE 1/2 AREA OF PARAPET WALL.

	9)ALL TOILET ROOMS SHALL BE EQUIPPED W/
	FLOOR DRAINS PER SPC SEC.409.4.1.1.

	10)SUBMIT COMPLETE GAS DRAWING FOR
	REVIEW.COMPLY W/ATTACHED REQS.

	11)P&T DRAIN FROM WATER HEATER SHALL
	DRAIN TO FLOOR SINK.SPC SEC.807.1.3.

	12)VACUUM RELIEF LINE SHALL BE INSTALLED
	PER MANUF.RECOMMENDATIONS AND ANSI
	Z21.22.

	13)EWH SHALL BE READILY ACCESSIBLE PER
	SPC SEC.501.7.SUPPLY SHIP'S LADDER AND
	PLATFORM OR RELOCATE HEATER TO FLOOR.

	14)HEATER SHALL BE EQUIPPED W/PAN AND
	DRAIN PER COUNTYWIDE AMENDMENTS TO SPC
	SEC.507.8.1.

	15)SUBMIT COMPLETE SIGNED AND SEALED
	PLANS FOR THE MEDICAL GAS SYSTEM.
	COUNTYWIDE AMENDMENTS TO SPC SEC.104.2.3

	CALL 561-659-8096,EXT.8377 IF YOU HAVE
	QUESTIONS.
	TIMOTHY LARGE
	PLUMBING PLANS EXAMINER

Review Stop	Z		ZONING
Rev No	1	Status	Date		Cont ID
Sent By			Date	Time	Rev Time
Received By			Date	Time	Sent To

Notes

***NONE***